Powerplus VI 2200 RLE Manual

Powerplus Ikke kategoriseret VI 2200 RLE

Læs gratis den danske manual til Powerplus VI 2200 RLE (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Powerplus VI 2200 RLE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Line-interactive UPS

PowerWalker VI 1200- RLE 3000

User Manual

IMPORTANT SAFETY INSTRUCTIONS

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this

manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION! T prevent the risk of re or electric shock, install in a temperature a humidity controlled indoor area free of conductive contaminants. (See the ond

specications for the acceptable temperature and humidity range.)

CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid exposing the unit to direct sunlight or installing the unit

near heat emitting appliances such as space heaters or furnaces.

CAUTION! Do not attach non-computer-related items, such as medical equipment life-support equipment, microwave ovens, or vacuum cleaners to UPS. ,

CAUTION! Do not plug the UPS input into its own output.

CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-containing vessels on or near the unit.

CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS.

CAUTION! Do not attach a power strip or surge suppressor to the UPS.

CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.

INSTALLING YOUR UPS SYSTEM

UNPACKING

The box should contain the following:

(1) UPS Unit x 1 (2) User Manual; 1; (3) USB Cable x 1; (4) RS232 Cable x 1;

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the battery power-supplied outlets does not exceed the UPS unit’s rated capacity. If rated unit capacities are

exceeded, an overload condition may occur and cause the UPS unit to shut down or the fuse blow.

2. There are many factors that can aect the amount of power that your computer system will require. For optimal system performance keep the load

below 80% of the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least 8 hours is recommended to ensure that the battery's

maximum charge capacity is achieved. Charge loss may occur during shipping and storage. To recharge the battery, simply leave the unit plugged into

an AC outlet. The unit will charge in both the on and o position.

2. With the UPS unit o and unplugged, connect the computer, monitor, and any externally powered data storage device.

3. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is protected by a fuse or circuit breaker and does

not service equipment with large electrical demands.

4. Depress the power switch to turn the unit on. The LCD indicator light will illuminate and the unit will "beep".

5. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

6. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to ensure battery

life.

ROUTINE MAINTENANCE AND STORAGE

ROUTINE MAINTENANCE

1. Use dry soft clothes to clean the front panel and plastic parts. Do not use any detergent that contains alcoholic ingredient.

2. The expected lifetime of the battery is around 3 years. Improper operation and harsh environment will reduce the actual lifetime.

3. Unplug the UPS from power inlet if the UPS will not operate for long period of time.

STORAGE

1. First turn o your UPS and disconnect its power cord from the wall outlet. Disconnect all cables connected the UPS to avoid battery drain.

2. The UPS should be stored in a cool dry location.

3. Make sure the battery is fully charged before the UPS is stored.

4. For extended storage in moderate climates, the battery should be charged for 12 hours every 3 months by plugging the power cord into the wall

receptacle and turning on the main switch. Repeat it every 2 months in high temperature locations.

BASIC OPERATION

FRONT AND TOP PANEL DESCRIPTION

PowerWalker VI 1200/ 2200 RLE Front View

PowerWalker VI 3000 RLE

1. Input Circuit Breaker

The circuit breaker provides optimal overload protection.

2. AC Inlet

Connect to utility power through the input power cord.

3. AC outlet

The UPS provides outlets for connected equipment to insure temporary uninterrupted operation during a power failure and against surges and spikes.

4. SNMP/HTTP Network Port

The SNMP/HTTP port provides remote monitoring and management of your UPS over a network.

5. RJ45/11 Communication Protection Ports

Communication protection ports will protect any standard modem, fax, telephone line, or network cable.

6. EPO Port

Enables an emergency UPS Power-O from a remote location. EPO terminal open, the UPS will turn off and the output shutdown immediately.

7. USB Port

This port allows connection and communication form the USB port on the computer to the UPS unit.

8. Serial Port

This port allows connection and communication from the DB9 serial on the computer to the UPS unit. The UPS communicates its status to the

software.

9. Not used

10. Power On/O Switch

Press the power switch to turn the UPS ON or OFF.

11. Mute Button

The audible alarm can be turned o/on by pressing this button.

12. LCD Display

The LCD will display the UPS status including input voltage, output voltage, runtime, percentage of load and battery, etc.

SOFTWARE DOWNLOAD

Power Master management software provides a user-friendly interface for your power systems. The graphic user-interface is intuitive and displays essential

power information at a glance. Please follow procedure below to install the software.

Installation procedure:

1.Download Power Master from the website:

http://www.powermaster. powerwalker.com

2.Double-click the le and follow the installation steps.

3.When your computer restarts, the Power Master

software will appear as a blue icon located in the

system tray.

TECHNICAL SPECIFICATIONS

LCD Indication

Line mode

Bat-mode

Alarm/Fault

Sound disable

(Press the mute key 3s to disable

and enable the buzzer sound)

Bat mode: battery capacity

Line mode:

1. Battery charging: cycle lighting

2. Battery full charged: lighting

3. Line mode without charger:

battery capacity

Load capacity

Setting Item

PV Mode

Initial

AC INPUT(Voltage)

OUTPUT

(Voltage)

TROUBLE SHOOTING

Problem

Possible Cause

Solution

The UPS does not perform

expected runtime.

Batteries are not fully charged.

Recharge the battery by leaving the UPS plugged in.

Battery is slightly worn out.

Contact Technical Support.

The UPS will not turn on.

The on/off switch is designed to prevent

damage by rapidly turning it o and on.

Turn the UPS o. Wait 10 seconds and then turn the UPS on.

The unit is not connected to an AC outlet.

The unit must be connected to a 220-240V 50Hz outlet.

The battery is worn out.

Contact Technical Support.

Mechanical problem.

Contact Technical Support.

Outlets do not provide power to

equipment

Fuse is blown due to overload

Turn the UPS o and unplug at least one piece connected

equipment. Unplug the power cord of the UPS then remove the fuse

compartment beneath the power inlet of the UPS and replace the

blown fuse with a spare one. Lock the compartment back to the UPS.

Connect power cord then turn the UPS on. Make sure that your spare

fuse meets the specication.

Batteries are discharged

Allow the unit to recharge for at least 4 hours.

Unit has been damaged by a surge or spike.

Contact Technical Support.

Software is inactive

The network cable is not connected.

Connect the network cable to the UPS unit and a network port on the

hub.

Software setting problem.

Please read and follow NetAgent utility instruction during installation

and operation of the NetAgent software, or contact technical support.

Fault

Fault code F09

Output Short :

Output circuit short.

1. Shut down the UPS

2. Your attached equipment may have problems, please remove

them and check again.

Fault code F11

Battery high: Battery voltage is too high.

1 Shut down the UPS .

2.Check the counts of Battery

Fault code F12

Battery Low :

Battery voltage is too low.

1. Shut down the UPS

2. Check the counts of Battery

3.Check battery connector when use battery packages.

Fault code F14

Overload in line Mode:

Your equipment requires more power than the

UPS can provide. It will transfer to Bypass

Mode.

Shut o non-essential equipment.If this solves the overload problem,

the UPS will transfer to normal operation.

Fault code F14

Overload in Battery Mode : Your equipment

requires more power than the UPS can provide.

It will shutdown.

Shut o non-essential equipment.If this solves the overload problem,

the UPS will transfer to normal operation.

Fault code F18

Fan fail :

Fan has been damaged.

1.Shut down the UPS

2.Replace the fan

Fault code F19

Over Temperature :

High ambient temperature The LCD will display

E11

1. Shut down the UPS. Restart the UPS to Check the fan for operation

and if the ventilation hole has been covered

2. Contact Technical Support.

Model

PowerWalker

VI 1200 RLE

PowerWalker

VI 2200 RLE

PowerWalker

VI3000 RLE

Capacity (VA)

1200VA

2200VA

3000VA

Capacity (Watts)

720W

1320W

1800W

Input

Input Voltage Range

165V~29 0V

Frequency Range

50Hz +/- 5 Hz

Output

On Battery Output Voltage

Sine Wave at 230Vac +/-10%

On Battery Output Frequency

50Hz - +/ 1%

Overload Protection

On Utility: Fuse, On Battery: Internal Current Limiting

AVR Function

Boost Function

Yes

Buck Function

Yes

Physical

Total # of UPS Receptacles

IEC C13 x 4

IEC C13 x 8

Maximum Dimensions (H x W) D x

88mm x 430mm x 438 mm

Weight (Kg)

11.93

16.47

21.78

Battery

Sealed Maintenance Free Lead Acid Battery

24V (2x12V/7.2Ah)

24V (2x12V/9Ah)

24V (4x12V/7.2Ah)

Typical Recharge Time

4 Hours

Warning Diagnostics

Indicators

Using AC / Using Battery / Fault

Communication

Software

Yes

Environmental

Operating Temperature

0 C to 40  C

Operating Relative Humidity

0 to 90% NON-CONDENSING

Management

Auto-Charger

Yes

Auto-Restart

Yes

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

Produkt Specifikationer

Mærke:	Powerplus
Kategori:	Ikke kategoriseret
Model:	VI 2200 RLE
Bredde:	438 mm
Dybde:	430 mm
Højde:	88 mm
Vægt:	16700 g
Produktfarve:	Sort
Batterispænding:	12 V
Batterikapacitet:	9 At
USB-port:	Ja
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Driftstemperatur (T-T):	0 - 40 °C
Støjniveau:	50 dB
Udgangseffekt:	1320 W
Harmoniseret systemkode (HS):	85078000
Antal understøttede batterier:	2
Indgangsfrekvens:	45/55 Hz
RS-232-porte:	1
Strømbeskyttelsesfunktioner:	Overbelastning
Strømstik:	C14 forbinder
AC udgange, antal:	4 AC stikkontakt(er)
AC stikkontakt typer:	C13 forbinder
Indgående driftsspænding (maks.):	290 V
Output strømkapacitet (VA):	2.2 kVA
Indgående driftsspænding (min.):	165 V
Udgangs driftsspænding (min.):	230 V
Udgangs driftsspænding (maks.):	230 V
UPS topologi:	Interaktivt indgangsstik
Typisk backup tid ved halv styrke:	7.1 min.
Typisk backup tid ved fuld styrke:	1.1 min.
Udgående strømfaktor:	0.6
Batteri genopladningstid (90 %):	4 t