Premier Mounts MM-BH284 Manual

Premier Mounts Vægophæng MM-BH284

Læs gratis den danske manual til Premier Mounts MM-BH284 (2 sider) i kategorien Vægophæng. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Premier Mounts MM-BH284, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Page 1 Installation Instructions

Installation Instructions

9531-000-041-00

Parts List

MM-CB2

Dual Multi-Monitor Mounting Arm

(Qty 1)

The MM-CB2 is a dual multimonitor mount arm that works with any

2” tubing. Each mounting head provides 90° of omnidirectional tilt.

The mounting heads include both 75x75mm and 100x100mm VESA

mounting patterns. The arm includes integrated cable management

tabs to keep wires and cables protected and organized. The mounting

heads can be horizontally adjusted.

Step 1

1. Slide your mounting arm over the pole and base (Figure 1)

(not included, but should be previously installed).

Determine the position on the pole desired for your mounting arm.

2. Once in desired position,tighten the two (2)

pre-intalled M8 x 6mm set screws in the

holes in the back of the MM-CB2. Tighten

with included allen key (Figure 2).

Step 2

M4 x 10mm Combo Screws

(Qty 8)

Introduction

MM-CB2

(Figure 1)

(Figure 3)

Are you installing to a 75x75mm or

100x100mm VESA moutning pattern?

For 75x75mm, use mounting points A. For

100x100mm use points B in gure 3.

1) Thread the M4 screws to one-half of their

length into the top two mounting holes on

each display, but do not tighten the M4

screws at this time.

Step 3

(Figure 2)

A A

B B

Thread Insert in Flat

Panel or Adapter Plate

M4 Screw Partially

Threaded Into Flat Panel

Keyhole Slot

MM-CB2 Mount

1) Insert the heads of the M4 screws through the keyhole slots on the

mounting head (Figure 5).

2) Insert the remaining two (2) M4x10mm screws, into the bottom mounting

points (Figure 4)

3) Repeat sub-steps 1 & 2 for the second display.

4) Tighten all M4 screws.

Do not overtighten the mounting hardware

Figure 4

Figure 5

Step 4

To adjust the position of your displays horizontally

1. Turn the mounting head adjustment knob counter clockwise until the

mounting head is lose enough to slide easily along the pole.

2. Slide the display (or mounting head) to the desired position.

3. When in place, turn the adjustment head clockwise to tighten it. Make sure

it is completely secure and does not move before you move on to the next

display or nish.

4. Repeat steps for other displays if desired.

Loosen

& Adjust

Tighten

& Secure

5/32” Allen Key

(Qty 1)

Socket Wrench

(Qty 1)

4” Cable Ties (Qty 2)

3100 E. Miraloma Avenue, Anaheim, CA 92806 | 800.368.9700 USA | F 800.832.4888 | www.mounts.com

Unit 3, The Moorings Business Park, Channel Way | Longford, Conventry, CV6 6RH, UK | +44 (0) 2476 644105 | F +44 (0) 2476 644165

Produkt Specifikationer

Mærke:	Premier Mounts
Kategori:	Vægophæng
Model:	MM-BH284
Bredde:	686 mm
Dybde:	711 mm
Højde:	508 mm
Vægt:	11400 g
Produktfarve:	Sort
Monteringstype:	Væg
Hældningsvinkelområde:	-90 - 90 °
Rotationsvinkel:	360 °
Maksimal vægtkapacitet:	45.5 kg
Pivot vinkel:	-90 - 90 °
Maksimal skærmstørrelse kompatibilitet:	24 "
Antal understøttede skærme:	4
Minimal skærmstørrelse kompatibilitet:	10 "
Montering interface kompatibilitet (min.):	75 x 75 mm
Montering interface kompatibilitet (maks.):	100 x 100 mm