Pro-Ject AD Box 52 Phono Manual

Pro-Ject Hi-Fi system AD Box 52 Phono

Læs gratis den danske manual til Pro-Ject AD Box 52 Phono (5 sider) i kategorien Hi-Fi system. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Pro-Ject AD Box 52 Phono, eller vil du spørge andre brugere om produktet?

Side 1/5
BY
PRO-JECT
AUDIO
SYSTEMS
INSTRUCTIONS
FOR
USE
Pro-Ject
AD
Box
52
Phono
Dear music lover,
thank you
for
purchasing this
AD
Box
S2
Phono from
Pro
-
Ject
Audio
Systems.
In order
to
achieve maximum performance and reliability you should study these instructions for use caref ully.
"\L7
Warning
of
o hazard
for
the
user,
the
unit
or
possible misuse
~
Important
notice
Safety instructions
AC
outlet voltages
vary
from country
to
country.
Before connecting
to
the mains, make sure
that
the
voltage
in
your area meets the voltage requirements printed on the power supply.
The
power supply is used
lo
disconnect the
unit
from
the
mains.
Make
sure that the power supply is ieas ly
accessible
at
all
times
. Never handle
the
device,
the
power supply
while
your hands
ore
wet
or
damp.
Avoid
letting
liquids
enter the device or the power supply. Never place any item
con1oining
liquid,
such as a
flower
vase on
or
near the device. Never spill any
liquid
on the device or the power supply.
Never
place
any
naked flame
sources,
such
as
lighted
rondles
on
or
near the device.
The
produd
shall
not
be
used
in
damp or wet
locations,
next
to
a
bathtub,
sink,
swimming
pool
or
any other
similar
condi . tions
Connectors
Phonotn
Left
,
+unetn n
\__j
Make
all
connections
whilst
the phono amplifier
is
disconnected from the power supply.
Take
care
lo
conned the left and
right
channels
correctly
.
The
right
channel
is
usually marked red, the
left channel black
or
white.
Do
not connect
the
phono
amplifiers
outpvt to o phono input (sometimes labelled gram, disc
or
RIM)
on the amplifier.
Never use any other power supply
than
the one supplied
with
the
unit
.
Connecting
the
record
player
or
a
line
level source
Conned
the tonearm signal lead
to
the
sockets
Phono
In of the phono amplifier. The earthing wire
of
the
tonearm signal lead may be connected
to
the screw terminal
if
you encounter hum problems when using the
record player.
The
signal lead
of
a line level source has
to
be
connected
to
the socket Une ln.
Setting
the
cartridge
mode
The phono amplifier con be used in either
MM
(for moving magnet and high-output
MC
cartridges)
or
MC
(for
low-output
MC
cartridges) mode according
to
the construction principle
of
the pickup cartridge
to
be
used.
Since most cartridges use the
MM
principle the phono amplifier
is
factory
set
to operate in this mode. To find
out which type your your cartridge is please consult the literature accompanying cartridge.
If
in
doubt please
consult your dealer.
A switch ot the bock
of
the phono amplifier
sets
the correct level
of
amplification for the cartridge.
W
Before
setting
MM
I
MC
mode the unit must
be
disconnected from
the
power supply and
amplifier
.
Connection
to
the
amplifier
Connect the
Out
of the phono amplifier to a (sline input uch as AUX, CD, Tuner, Tape
or
Video)
on
your
amplifier.
2 ©
Pro
-J t ec
Audio
System
s ·
Pro
-
Je
ct
AD
Box
52 · Phono
Rev
isio
n
2017
.6. 15


Produkt Specifikationer

Mærke: Pro-Ject
Kategori: Hi-Fi system
Model: AD Box 52 Phono

Har du brug for hjælp?

Hvis du har brug for hjælp til Pro-Ject AD Box 52 Phono stil et spørgsmål nedenfor, og andre brugere vil svare dig