PRV Audio MDX1800.1 Manual

PRV Audio Modtager MDX1800.1

Læs gratis den danske manual til PRV Audio MDX1800.1 (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 3 anmeldelser. Har du et spørgsmål om PRV Audio MDX1800.1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Before connecting your ampliﬁer review all recommendation. Any connection to the ampliﬁer input or output must be performed only when ampliﬁer is OFF.

The gauge of the power supply wiring is extremely important to reach the desired ampliﬁer output and for the ampliﬁer’s safety. Not using the recommended wire gauge will result in power loss and overheating

of cables. It is important that the power supply cables are the shortest possible length, maximum recommended length is 10 feet. Always use 100% Cooper cables and good quality connectors. This guarantees

the sound’s quality and ﬁdelity; To avoid damaging the cables, make sure that they do not touch sharp metal edges. Important: Use a fuse 12 inches away from the battery as a safety precaution.

In order to avoid interferences, the signal cables ( RCA) must be kept away from the original wiring of vehicle and from any other power supply cable.

Ampliﬁer must be installed in a solid and ventilated area. Do not mount ampliﬁer to the back of a subwoofer box; excess vibration may cause damage to the ampliﬁer.

The power rated data are based on equipment from the PRV Audio Group laboratory.

Frequency reference of 100Hz to 1kHz with THD+N to ≤1 % in impedances referring to the indicated in each measurement. The electronic components and the

manufacturing process can present manufacturing variations, thus leading to a variation in the measurements made. This ampliﬁer is designed to perform on music

applications ( with speakers ), any load test ( resistant load ) is not recommended.

Model

Channels

Rated RMS Power at 14.0 V at 1 Ohm

Rated RMS Power at 14.0 V at 2 Ohm

Rated RMS Power at 14.0 V at 4 Ohm

Average Efﬁciency

Operating Voltage

Musical Current Draw

Minimal Power Wire Input

Built-in Crossover

Minimal Speaker Wire Output

Frequency Response (-3dB)

RCA Min/Max Voltage Input

Speaker Wire Min/Max Voltage Input

Signal Input

Signal To Noise

Protection System

Heat Sink Type

Dimensions ( Width x Depth x Height )

Weight

Never use speakers with impedance under the nominal impedance of the ampliﬁer.

Warranty will be voided if ran below their rated ohm load.

HPF / Subsonic

LPF

Variable High Pass Filter at 12dB/Oct slope allows adjustment from:

MDX1800.1 - 10Hz to 120Hz MDX2500.1 - 10Hz to 160Hz

It determines the beginning of the ampliﬁer operating frequency. Allows the elimination of low

frequency sounds, delivering the right frequency range to avoid damage to the components.

Variable Low Pass Filter allows adjustment from 50Hz to 1,000Hz at 12dB/Oct Slope, when

switch is Turn On. When switch is turn Of f ampliﬁer will be at full range up to 25,000Hz.

It determines the end of the ampliﬁer operating frequency. This ensures that only the lowest

frequencies are reproduced by the ampliﬁer.

Crossover / Filter

MDX2500.1 2Ω

----

1x 2700 Watts RMS

1x 2000 Watts RMS

86%

9 - 16 volts

140A

10 - 25,000 Hz

8.50” x 5.90” x 2.60”

4.00 Lbs

MDX1800.1 2Ω

----

1x 1800 Watts RMS

1x 1100 Watts RMS

86%

9 - 16 volts

72A

10 - 25,000 Hz

6.60” x 5.90” x 2.60”

2.80 Lbs

LED Indicator

CLIPPING YELLOW LED Occasionally with Strong Music Notes

- Indicates when ampliﬁer output begins to distort the sound.

The clipping LED is a tool to diagnose when you have reached the limit of the ampliﬁer output.

It will blink if you have exceeded the max output power on the true working impedance of the

ampliﬁer or due to the lack of battery power in the system.

-Ampliﬁer must not operate with excessive ﬂashing of the clipping LED.

Abuse may cause damage to ampliﬁer or speakers.

- If Audio CUT-OFF and the YELLOW LED is “FLASHING” this indicates a protection system

against Short-circuit or impedance lower than supported by the output.

ON BLUE LED

- When LED is “ON”indicates ampliﬁer is ON, ready to operate.

- When LED is “FLASHING” indicates Low/High battery voltage

protection. Ampliﬁer must operates between 9 to 16 volts.

- When LED is “ON”indicates High Temperature Protection for excessive temperature. Audio

stops and the fans run at maximum speed to cool internal components.

- When LED is “FLASHING” indicates Damage Ampliﬁer Protection.

This means the ampliﬁer has some damage, can no longer operate, and must be sent to one

of our technical repair centers for review.

PROTECTION RED LED

MDX1800.1 1Ω

1x 1800 Watts RMS

1x 1100 Watts RMS

----

86%

9 - 16 volts

75A

Variable HPF 10Hz - 120Hz & LPF 50Hz - 1kHz

14 Gauge

10 - 25,000 Hz

6.60” x 5.90” x 2.60”

2.85 Lbs

MDX2500.1 1Ω

1x 2600 Watts RMS

1x 1850 Watts RMS

----

84%

9 - 16 volts

149A

Variable HPF 10Hz - 160Hz & LPF 50Hz - 1kHz

12 Gauge

8.50” x 5.90” x 2.60”

4.05 Lbs

(OFC) 4 Gauge wires

10 - 25,000 Hz

0.2 to 2v

1.5 to 15v

RCA Cables OR Speaker Wire Inputs

>90dB

Low & High Supply Voltage / Shortage on Output / Low Impedance on Output

Mini Heavy Duty Cast Aluminum

MINI AMPLIFIER

Produkt Specifikationer

Mærke:	PRV Audio
Kategori:	Modtager
Model:	MDX1800.1

Har du brug for hjælp?

Hvis du har brug for hjælp til PRV Audio MDX1800.1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager PRV Audio Manualer

PRV Audio MDX1800.1 Manual

3 December 2025

Modtager Manualer

Nyeste Modtager Manualer

AIYIMA T5 Manual

3 December 2025

Topping MX5 Manual

30 November 2025

Topping Mini 300 Manual

29 November 2025

Diamond Audio HX600.4 Manual

29 November 2025

Diamond Audio HX1600.1D Manual

28 November 2025

Topping PA3s Manual

28 November 2025

Topping B100 Manual

27 November 2025

Hifonics Titan Evolution TXE2000/1 Manual

27 November 2025

Topping Pre90 Manual

27 November 2025

Diamond Audio HX800.1D Manual

27 November 2025