PSB CustomSound CW50R Manual
Læs gratis den danske manual til PSB CustomSound CW50R (19 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 17 anmeldelser. Har du et spørgsmål om PSB CustomSound CW50R, eller vil du spørge andre brugere om produktet?
Side 1/19
®
In-Wall Loudspeaker
Installation Guide
I.
II.
CONTENTS
Materials And Tools
A. Required Tools
B. Other Tools
Layout
A. Listening Locations
B. Speaker Locations
C. System and Supply
D. Obstructions
E. Weather Resistance
F. Tricks of the Trades—Nothing's Plumb, Square, or True
III. Installation
A. New Construction
B. Enclosure Volume and Insulation
IV. Wiring
A. Rough-in Wiring
B. Finish Wiring
C. Tricks of the Trades—Drilling
V. Grilles
A. Installing and Removing
B. Grille Alternatives—Scrims, Hole Shapes and Sizes
Painting
A. Construction Dust and Paint Shield
VI.
B. Painting Finish Frames
C. Painting Grilles
VII. Setup
B. High and Mid Frequencies Switches
C. Bipole and Dipole Switches
A. Swivel Tweeter
2
D. Listening—Balance, Range, and Imaging
I. MATERIALS AND TOOLS
The only other materials necessary to install CustomSound speakers are paint
and extra fine sandpaper if you wish to change the color of Grills and/or Finish
Frames from their standard white. Of course, wire cable of appropriate length and
size will be necessary to connect speakers to amplifiers (or volume controls) in
the music system.
A. Required Tools
The following tools are needed for normal, simple installations:
Tape Measure, Pencil, and Level
Utility Knife and Wallboard Saw (and extra blades)
Philips Screwdriver and Putty Knife
Drill and Bits (smaller for lead holes and larger for cabling)
Probe Wire (a heavy coat hanger can substitute for a short fish-tape)
Flashlight
B. Other Tools
Particularly when installing a quantity of speakers, or installing in wood paneling
or other wall materials, the following tools are desirable for neater and more
efficient installations:
Stud Finder (helpful—particularly with simple, wallboard-on-studs
construction)
Metal Straight Edge (Ruler or Framing Square) and Masking Tape
Wallboard Rasp/Sanding Block (or a piece of wire lath around a block)
Awl or Worn Screwdriver (for initial, exploratory holes) and Hammer
Wire Cutters/Strippers and Electrical Tape
Battery Screwdriver and Power Drill and Extensions (with extra bits)
Jig Saw and Blades
Wallboard Router and Cutout Bits
II. LAYOUT
A. Listening Locations
Consider the desired, intended, and probable locations of listeners when
considering speaker locations. Ideally, listeners should have a clear line-of-
sight/hearing to all speakers in their listening area—not too far off axis and not
obstructed by structure or furnishings—for most balanced frequency response.
Where will listeners be—primary and secondary? Where will listeners’ ears
be—sitting, standing, walking? No installation is absolutely ideal, but considering
listener locations with speaker location can greatly improve the final result—and
simplify the effort and expense to achieve it.
3
Produkt Specifikationer
| Mærke: | PSB |
| Kategori: | Højttaler |
| Model: | CustomSound CW50R |
Har du brug for hjælp?
Hvis du har brug for hjælp til PSB CustomSound CW50R stil et spørgsmål nedenfor, og andre brugere vil svare dig
Højttaler PSB Manualer
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
17 August 2024
Højttaler Manualer
- Victrola
- Raymarine
- Xvive
- NUU Mobile
- Autotek
- Teac
- Ices
- Klip Xtreme
- Canon
- PRIME3
- Audiotec Fischer
- Nest
- BlueAnt
- Innovative Technology
- Boynq
Nyeste Højttaler Manualer
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
20 Juni 2025