Radial Engineering Bones London Manual

Radial Engineering Ikke kategoriseret Bones London

Læs gratis den danske manual til Radial Engineering Bones London (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Radial Engineering Bones London, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

True to the Music

LONDON DISTORTION

OWNER’S MANUAL

Radial Engineering Ltd.

Part # R800 7105

Bones London Distortion

FEATURES AND FUNCTIONS

1. : 1/4" input jack for your guitar.IN

2. : 1/4” output jack connection to your amp.OUT

3. : Connection for 9-12 volt DC (center pin negative ).PSU

4. BYPASS: Footswitch toggles between distortion and clean bypass. An

on/off LED status indicator illuminates when the distortion is active.

5. TOGGLE: Choose between the two output LEVEL controls by depressing

the footswitch. LEVEL-1 is voiced for rhythm guitar while LEVEL-2 is

augmented in the mid-range to increase sustain and cut for solos. An

LED status indicator illuminates when channel-2 is active.

6. : Used to adjust overall amount of distortion.DRIVE

7. : Two-band EQ shapes treble and bass response. HIGH & LOW

8. BITE : Three position BITE switch controls the overall high-end character.

Choose between ﬂ at response ( ), high-end boost ( ) or high-end

cut ( ).

9. KICK: Three position KICK switch is a mid-range control that can be called

upon to add +7dB or +12dB of mid-range boost for sustain.

10. LEVEL 1 & 2: Both channels are equipped with a level control that lets

you adjust the overall output volume of each channel separately. Think of

these like the master volume control on a guitar ampliﬁ er.

CONGRATULATIONS on your purchase of the Bones London distortion.

The London is a solid-state distortion pedal with a multi-stage drive circuit

that produces high-gain tones reminiscent of Plexi-style tube ampliﬁ ers. The

key to this pedal is how well the circuit retains note clarity even when driven

to extreme levels of saturation. Like the English Navy the London Bones will

never get soggy or sink into the mud.

For maximum on-stage efﬁ ciency, the London is conﬁ gured for clean,

rhythm & lead playability. In bypass mode, you get the natural clean sound

of your guitar. When the London is activated, you can select between two

variable LEVEL controls. Use LEVEL-1 to set a volume for rhythm guitar and

LEVEL-2 for soloing. To increase sustain and cut for solos, the second drive

circuit is augmented in the mid-range.

The tone and drive controls work together to deliver a shepherd’s pie of

British tones. The variable DRIVE control lets you dial-in the perfect amount

of distortion and the powerful dual-band equalizer with Radial’s distinctive

passive-interactive circuit shapes the overall sound. A 3-position KICK

switch can add extra mid-range drive or fatten up single coil pickups. A 3-

position BITE switch controls high-end character of the sound and lets you

compensate for overly bright amps or add extra sizzle.

The London is a high-gain distortion pedal that delivers decades of Plexi-

style sounds in a compact and easy to use format. God save the Queen!

POWERING THE LONDON DISTORTION

Bones pedals require an external power adapter that outputs 9 to 12 volts

DC with a 2.1mm barrel jack wired center pin negative

. Bones

pedals will draw a max of 100mA. Possible damage may occur if another

type of power adapter is used. Consult your dealer for more information.

CONNECTIONS AND SETUP

Before you begin, turn your guitar ampliﬁ er OFF. Connect the power supply

adaptor. The LEDs illuminate when a footswitch is depressed indicating the

pedal is powered up and ready for use.

To start, place the pedal in bypass mode by

depressing the BYPASS footswitch (LED

off) and set the controls as pictured. This will

give you a good starting sound while getting

to know your London distortion.

Connect your guitar to the IN jack.

Connect the OUT jack to your ampliﬁ er.

Always test your connections with your amp set at a low volume level. Turn

your amp on. If no sound is heard check the guitar and power connections.

Turn your amp up to a comfortable playing level. While in bypass mode set

up your clean (or not so clean) sound on your amp.

Activate the pedal by depressing the BYPASS footswitch (LED on). Select

channel-1 by depressing the TOGGLE footswitch (LED off). Adjust the

LEVEL-1 control so the volume is a little louder than the bypassed volume.

Depress the TOGGLE footswitch again and set up the LEVEL-2 control a

little louder for solos and you’re ready to rock.

You will ﬁ nd that most of the controls are intuitive and extremely sensitive

to changes. Small control adjustments will make big changes in the sound.

Take your time, experiment and have fun.

www.radialeng.com

Radial Engineering Ltd. • 1588 Kebet Way, Port Coquitlam, BC Canada V3C 5M5

Tel: 604-942-1001 • Fax: 604-942-1010 • email: info@radialeng.com

RADIAL LIMITED THREE YEAR TRANSFERABLE WARRANTY

Radial Engineering Ltd. warrants this product to be free from defects in material and workmanship and will remedy any such

defects free of charge according to the terms of this warranty. Radial Engineering will repair or replace at its option any defec-

tive component(s) of this product, excluding the ﬁ nish, the footswitch (tubes and footswitches are warranted for 90 days) and

wear and tear from normal use, for a period of three (3) years from the original date of purchase. In the event that a particular

product is no longer available, Radial Engineering reserves the right to replace the product with a similar product of equal or

greater value. In the unlikely event that a defect is uncovered, please call 1-800-942-1001 or email service@radialeng.com

to obtain an RA number (Return Authorization number) before the 3 year warranty period expires. Once you have obtained

an RA number you must return the product, freight prepaid, within ﬁ fteen (15) days after the date the RA number is issued. To

make a request or claim under this limited warranty, the product must be returned prepaid in the original shipping container (or

equivalent) to Radial Engineering or to an authorized repair centre and you must assume the risk of loss or damage. A copy

of the original invoice showing date of purchase and the dealer name must accompany any request for work to be performed

under this limited warranty. This limited warranty shall not apply if the product has been damaged due to abuse, misuse,

misapplication, accident or as a result of service or modiﬁ cation by any other than an authorized repair centre.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE HEREOF AND DESCRIBED ABOVE.

NO WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRAN-

TIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL EXTEND BEYOND THE RESPEC-

TIVE WARRANTY PERIOD DESCRIBED ABOVE OF THREE YEARS. RADIAL ENGINEERING SHALL NOT BE RESPON-

SIBLE OR LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE

USE OF THIS PRODUCT. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER

RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU LIVE AND WHERE THE PRODUCT WAS PURCHASED.

FREQUENTLY ASKED QUESTIONS

Can I use any 9 volt adapter to power the Bones?

There are many adapters that can supply 9-12 volts DC but to be compatible the adapter must also have a 2.1mm barrel plug wired center pin negative. The Bones draw

100mA of current to operate. Your adapter can be rated higher, for example 500mA, but not lower.

I hear a high frequency “whine”. What causes this and how do I get rid of it?

Most likely this is caused by the power adapter you are using. Some switching type power adapters can make noise that bleeds into the guitar signal. If you encounter high

frequency noise try a different adapter. We recommend standard linear adapters although we have successfully tested the Bones with both types.

Is the London a true bypass pedal?

No. The London features active buffering in bypass mode that lowers the output impedance allowing longer cables without noise or tone loss. This also enables us to

employ EIS - Electronic Impulse Switching that eliminates certain problems with true bypass designs. True bypass switching can be noisy when switching pedals on and

off producing pops and clicks. If used in conjunction with high-gain amps that “pop” can become a loud “bang”. The EIS switch is 100% noiseless.

Which is better, True Bypass or Buffered Bypass?

Buffers are a good thing to have in your signal chain. They regulate your signal and lower the output impedance to drive long cables and dirty (oxidized) jack contacts.

However, buffers have received a bad reputation because some manufacturers design their buffer circuits to save money. That design strategy limits overall sound quality

of the bypassed signal and has created a demand for a better system. The simplest alternative was to do away with the buffer and provide a hard-wired bypass via a me-

chanical switch and the term “true bypass” was born. But this arrangement has a downside too. Mechanical switches can make noise and are less reliable than electronic

switching. The Bones are designed with a great sounding class-A buffer that emulates the input impedance of a typical tube amp. With a well designed buffer you get less

noise and great tone.

Why can’t the London be powered by a battery?

It’s because of the class-A topology. Class-A circuits sound best but are power hungry and will drain a battery in no time.

How should I set the sound on my amp?

The London is a two channel pedal based on the “clean, rhythm, lead” concept. The two channels in the London can supply the chunky rhythm tones and searing lead

sounds while your amp provides a base “clean” sound. Think of your amp as a blank canvas and the London as a pallet full of paints.

I use several pedals. Where’s the best place to put the London in my signal chain?

There are no rules but there are general guidelines when it comes to distortion pedals. If you place a booster before a distortion it will increase the amount of saturation but

your guitar volume will stay about the same. If the booster is placed after it will increase your guitar volume without changing the tone of the pedal. Placing the London be-

fore pedals like a chorus, ﬂ anger and phaser will make their effects more prominent because of the increased harmonics the distortion adds. Experiment and have fun.

DECLARATION

OF CONFORMITY

Radial Engineering Ltd. declares that

this product conforms to the following

speciﬁ cations:

Safety: IEC 60065 (1998), EMC: EN

55013 (1990), EN 55020 (1991)

Supplementary information: The

product herewith complies with the

requirements of the Low Voltage Direc-

tive 72/23/EEC and the EMC Directive

89/336/EEC as amended by Directive