Radial Engineering Elevator Manual

Radial Engineering Ikke kategoriseret Elevator

Læs gratis den danske manual til Radial Engineering Elevator (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Radial Engineering Elevator, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

www.radialeng.com

True to the Music

Radial Engineering Ltd.

True to the Music

USER GUIDE

Radial Engineering Ltd.

Elevator

™

Elevator

™

FEATURES

RADIAL ENGINEERING 3 YEAR

TRANSFERABLE LIMITED WARRANTY

RADIAL ENGINEERING LTD. (“Radial”) warrants this product to be free from defects in

material and workmanship and will remedy any such defects free of charge according to the

terms of this warranty. Radial will repair or replace (at its option) any defective component(s)

of this product (excluding nish and wear and tear on components under normal use) for

a period of three (3) years from the original date of purchase. In the event that a particular

product is no longer available, Radial reserves the right to replace the product with a similar

product of equal or greater value. In the unlikely event that a defect is uncovered, please call

604-942-1001 or email service@radialeng.com to obtain a RA number (Return Authorization

number) before the 3 year warranty period expires. The product must be returned prepaid

in the original shipping container (or equivalent) to Radial or to an authorized Radial repair

center and you must assume the risk of loss or damage. A copy of the original invoice showing

date of purchase and the dealer name must accompany any request for work to be performed

under this limited and transferable warranty. This warranty shall not apply if the product has

been damaged due to abuse, misuse, misapplication, accident or as a result of service or

modication by any other than an authorized Radial repair center.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE

HEREOF AND DESCRIBED ABOVE. NO WARRANTIES WHETHER EXPRESSED

OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL EXTEND

BEYOND THE RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE OF THREE

YEARS. RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE USE OF

THIS PRODUCT. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU

MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU

LIVE AND WHERE THE PRODUCT WAS PURCHASED.

Elevator

™

Specications and appearance are subject to change without notice.

Radial Engineering Ltd.

1588 Kebet Way, Port Coquitlam BC V3C 5M5

tel: 604-942-1001 • fax: 604-942-1010

info@radialeng.com • www.radialeng.com

Circuit type ..................................................................100% discrete Class-A

Drag Control ............................................... Variable from 22k ~ 1 meg-Ohms

Baseline gain .......................................................Variable from unity to +9dB

Boost gain ..........................................................Variable from unity to +18dB

Mid boost ...................................................... +5dB at 1kHz, +9.5dB at 800Hz

Footswitch ............................................................ Momentary (controls relay)

Relay type .............................................................. Sealed with gold contacts

Power ..................................................................9VDC, adapter not included

Radial Elevator Specications

G U I TA R B O O S T E R A N D L I N E D R I V E R

1. 9VDC POWER: Connection for 9 volt (center negative) power adapter.

Includes a cable clamp to prevent accidental power disconnection.

2. OUTPUT: High-Z ¼” connection to your amplier.

3. INPUT: High-Z ¼” connection from your instrument.

4. BASELINE SELECTOR: Three position switch sets the way the Elevator

handles your instrument signal when the power booster is not in use.

• TRUE-BYPASS: Takes the Elevator completely out of the signal path.

• BUFFER: Uses a unity gain buffer to drive long cables without added

noise or signal loss. Also activates the DRAG™ control.

• DRIVE PRESET: Lets you preset a baseline amount of gain.

5. DRAG: Load Correction circuit lets you replicate the tone and feel as if

connected directly to your amp.

6. DRIVE: Lets you dial-in a little extra punch and push your amp harder.

7. FOOTSWITCH: Activates the power BOOSTER. An LED indicator

illuminates when the BOOSTER is active.

8. GAIN: Controls the amount of boost applied when the BOOST footswitch

is active. Adds up to 15dB of clean gain.

9. MID BOOST: Three position switch lets you add extra mid-range for

greater sustain and stage presence.

• Position 1: OFF: No mid-range boost is applied.

• Position 2: 5dB: Applies a small amount of mid-range boost.

• Position 3: 10dB: Applies a big mid-range boost.

10. STEEL ENCLOSURE: Heavy-duty 14-gauge steel enclosure for long life.

123

OvERvIEW

The Elevator is a combination buffer and power booster and designed to be

the driving force on your pedalboard. What makes it unique is that you can

set up the Elevator to work in a variety of ways, depending on your personal

preference and playing style.

The Elevator has two basic sections, the baseline and the power booster. The

baseline section controls how the Elevator handles your instrument signal

when the power booster is bypassed. The power booster section lets you

kick up the gain for solos and includes a mid-range switch that further helps

to cut through the mix.

Baseline

Section

Booster

Section

Booster

Footswitch

& LED

MAkING cONNEcTIONS

Before you make any connections, it is a good idea to set your amp to

standby or turn it off. This will avoid loud power and connection transients

from reaching the loudspeakers and your ears. There is no power switch for

the Elevator. As soon as you plug in your power supply, it will spring to life. A

handy cable clamp next to the power jack can be used to prevent accidental

disconnection. The Elevator does not come with a power supply nor can it

be powered by an internal battery. You will need to purchase a ‘Boss’ style

9 Volt supply or use a multi-pedal power source.

Normally, the Elevator will be the rst pedal in your chain. For testing it is a

good idea to start without other effect pedals in the signal chain. This way

you will get a good sense of how each function works and sounds on its own.

Connecting to the Elevator is done using a standard high impedance guitar

cable with ¼” connectors. It is a good

idea to keep the cable between your

guitar and the Elevator as short as

possible to reduce the potential for noise.

High impedance cables work best when

less than 6 meters (20’) in length.

Connecting from the Elevator to your

amp is done using a second high

impedance guitar cable. The length of

this cable can vary depending on which

baseline setting you choose.

START-Up SETTINGS

Before turning on your amp, set up the Elevator controls as follows:

Baseline settings

• Baseline: set to TRUE BYPASS.

• DRIVE: turned fully counter-clockwise.

• DRAG: set to the 12 o’clock position.

Power booster settings

• Mid-range switch: set to OFF.

• GAIN: turned fully counter-clockwise.

• Footswitch: set to bypass (LED off).

ESTABLIShING ThE BASELINE

Power on your amp and slowly turn up the volume to a comfortable volume level.

Set your amp to a clean sound to begin with. The Baseline section gives you a

3-position switch and two set & forget controls that let you control how the Elevator

works when the power booster is bypassed ( ). footswitch LED off

TRUE BYpASS: At this setting the Elevator will have no effect on your sound

when the booster is bypassed. Some guitarists prefer the TRUE BYPASS setting

because the Elevator is taken completely out of the signal path when not using the

power booster. This has the benet of being a ‘true’ straight wire connection but

tends to introduce switching noise when used with high gain amps. If you choose

the TRUE BYPASS setting its important the total length of your high impedance

cables is limited to 8 meters (25’) or less for good results.

INPUT

OUTPUT

BUFFER

DRIVE

GAIN

BOOST

FOOTSWITCH

DRAG

BOOSTER

GAIN

MID

BOOST

BUFFER

DRIVE PRESET

TRUE BYPASS

BASELINE SWITCH

BUFFER: Moving the Baseline switch to the middle position activates the unity

gain buffer and the DRAG™ Control. A unity gain buffer is basically an amplier

that does not add or take away any gain. It is designed to condition the signal and

lower it’s output impedance in order to drive longer cables without noise or signal

loss. The BUFFER setting lets you employ high impedance cables as long as 16

meters (50’) between the Elevator and your amp with good results.

BOOST

FOOTSWITCH

OUTPUT

DRIVE

GAIN

BOOSTER

GAIN

MID

BOOST

BASELINE SWITCH

INPUT

BUFFER

DRAG

BUFFER

DRIVE PRESET

TRUE BYPASS

DRAG cONTROL: Radial’s DRAG Control load correction allows you to dial

in just the right amount of loading for your pickups to create the same tone

as if plugging directly into your amplier. With DRAG set at the 12 o’clock

position, strum a chord and use a small screwdriver or guitar pick to slowly

turn the DRAG control until the tone sounds right to you.

DRIvE pRESET: If you move the Baseline switch all the way to the right,

you will activate the DRIVE control. This innovative control lets you increase

the level and drive your amp harder when the power booster is bypassed

( ). The idea is that you can use the set & forget DRIVE footswitch LED off

control to preset just the right amount of baseline gain for your setup.

BOOST

FOOTSWITCH

OUTPUT

DRIVE

GAIN

BOOSTER

GAIN

MID

BOOST

INPUT

BUFFER

DRAG

BUFFER

DRIVE PRESET

TRUE BYPASS

BASELINE SWITCH

Try setting your amp to a slightly dirty sound and then use a small screwdriver

or guitar pick to slowly turn the DRIVE control clockwise. As you increase

the gain, it will drive your amps input harder enhancing the harmonics and

saturation. There’s enough gain on tap here to make your amp do a whole

lotta shakin’ so tread lightly at rst.

pOWER BOOSTER

The power booster section has three controls, the

GAIN knob, the mid-range switch and the footswitch.

Start with the 3-position mid-range switch set to the

OFF position. Depress the BOOST footswitch and

bring up the power booster level by rotating the GAIN

knob clockwise. The footswitch LED illuminates to let

you know that the power booster is active. Note that

with a clean amp sound, the booster can get very loud. You may have to turn

your amp’s master volume down. When using an already distorted sound,

the power booster will add harmonics and sustain to your guitar. Adjust the

GAIN control to nd the boost level that works best.

MID-RANGE SWITch: The power boost section is equipped with a 3-position

switch that lets you increase the mid-range content of the signal. Move the

switch to the middle 5dB position for a little mid-range boost. The 10dB

position further boosts the mid-range increasing the sustain and presence of

your guitar on stage and in the room. Keep in mind that electric guitar lives

in the mid-range so boosting it can really help dene your sound in a busy

mix. This can be particularly useful with single coil pickups that are not as

fat sounding as their humbucker counterparts.

BALANcING ThE BUFFER AND BOOSTER: Go back and compare the

tone when using a baseline buffer versus the true bypass setting. Work at

balancing the gain between the baseline and the power booster until you

decide what works best for you. Have fun and experiment. The Elevator is

very exible and there are no rules.

Radial Engineering Ltd. Radial Engineering Ltd. Radial Engineering Ltd.

Elevator

™

Elevator

™

Elevator

™

Produkt Specifikationer

Mærke:	Radial Engineering
Kategori:	Ikke kategoriseret
Model:	Elevator

Har du brug for hjælp?

Hvis du har brug for hjælp til Radial Engineering Elevator stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Radial Engineering Manualer

Radial Engineering JS3 Manual

20 Juli 2025

Radial Engineering Loopbone Manual

18 Juli 2025

Radial Engineering JS2 Manual

18 Juli 2025

Radial Engineering JR-5 Manual

18 Juli 2025

Radial Engineering JX62 Manual

17 Juli 2025

Radial Engineering North-Star Manual

17 Juli 2025

Radial Engineering PreMax Manual

15 Juli 2025

Radial Engineering Workhorse WR-8 Manual

14 Juli 2025

Radial Engineering SGI-44 Manual

14 Juli 2025

Radial Engineering Catapult Rack TX Manual

2 April 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MSW -JJS-E1K Manual

17 August 2025

Bellari BA525 Manual

17 August 2025

YA-MAN Deep Skin Clear Manual

17 August 2025

Singercon SIN-ALD-3000 Manual

17 August 2025

LG 32LQ631C0ZA Manual

17 August 2025

Vivax TS-7504G Manual

17 August 2025

MSW -ECJ-12-02 Manual

17 August 2025

CSL 300963 Manual

17 August 2025

Mars Gaming MCPU-VR Manual

17 August 2025

MSW -PLO-1350 Manual

17 August 2025