Radial Engineering StageBug SB-15 Manual

Radial Engineering Ikke kategoriseret StageBug SB-15

Læs gratis den danske manual til Radial Engineering StageBug SB-15 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Radial Engineering StageBug SB-15, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Thank you for purchasing your very own StageBug SB-15 Tailbone voltage converter

with active instrument buffer! We are excited about producing a personal device that

can fit in your instrument case and be ‘at the ready’ anytime you need to power your

Tonebone pedals with common 9 volt power bricks. Although the SB-15 is designed

to be plug & play easy to use, please take a minute to read this short manual. It will

give you insight on how to get the most out of your SB-15 Tailbone.

OVERVIEW

The Radial StageBug SB-15 Tailbone is a combination voltage converter and buffer

that enables the user to power any Tonebone pedal from two 9 volt DC power

supplies. It is designed to work with standard 9 volt ‘center-negative’ pedal power

supplies that feature multiple power outputs. The SB-15 Tailbone also features a built

in instrument buffer with DRAG ™ control.

USING THE VOLTAGE CONVERTER

Before making connections, it is good practice to turn your amp’s volume down to

ensure loud transients are not passed on to sensitive loudspeakers. Like the majority

of guitar pedals, the SB-15 uses standard 2.1mm barrel jacks for the DC

connections. Connect two DC cables from your power brick to the SB-15’s IN-1 &

IN-2 jacks. Next, connect a DC cable from the 15 volt OUT jack to your Tonebone

pedal and you’re set to go.

9V IN1: Accepts 9 volt

center-negative power

supply.

9V IN2: Accepts a

second 9 volt power

supply.

¼” BUFFER IN: High-Z

instrument input for

guitar and bass.

15V OUT: Power

output for Radial

Tonebone pedal.

DRAG

™:

Load correction

for the buffer

¼” BUFFER OUT:

High-Z buffered

instrument output.

FILT ER LEVEL DRIVE

HIGH LOW FILTER

TOP END

BRIGHT

FLAT

DARK

OUTPUT

LEVEL-2 DRIVE -2LEVEL-1 DRIVE -1

INSERT

12AX7

TUBE

DRIVE

CH.1 I NTERME DIATE DRIVE

TOGGLE

15VDC · 400mA

HIGH

MED

12dB

7dB

INPUT

TRUE BYPASS

LOWOUT

MID BOOST

DRIVE GAIN1

21Made in Canada

9V9V9V9V

DC OUTPUTS

FILT ER LEVEL DRIVE

9V Pedals15V Tonebone Pedal

BrighterDarker

DRAG™

USING THE INSTRUMENT BUFFER

When driving very long cables or a chain of true bypass effect pedals, you may notice

your guitar sounds dull compared to a straight connection to your amp with a short

cable. This high frequency loss is caused by high capacitance and resistance from

the cables in your signal chain and the various connections through your pedals.

Insert the SB-15 buffer using standard ¼” cables. Placing it ahead of these loads will

restore the clarity and impact of your instrument for a much more natural tone.

Drive a chain of true bypass pedals and a long cable to your amp.

FILTER LE V E L DRIVEFILTER LE V E L DRIVEFILTER LE V E L DRIVE

FILTER LEVEL DRIVE FILTER LEVEL DRIVE

HIGH LOW FILTER

TOP END

BRIGHT

FLAT

DARK

OUTPU T

LEVEL-2 DRIVE-2LEVEL-1 DRIVE-1

INSERT

12AX7

TUBE

DRIVE

CH.1 INTERME DIATE DRIV E

TOG GL E

15VDC · 40 0 mA

HIGH

MED

12dB

7dB

INP

TRUE BY PASS

LOWOUT

MID BOOST

DRIVE GAIN

21Mad e in Can a da

True bypass pedals SB-15 Buffer

Amp

FILTER LEVEL DRIVE FILTER LEVEL DRIVE

FILTER LEVEL DRIVE LTER LEVEL DRIVE

Drive two amps and a tuner through a Radial BigShot AB/Y switcher.

SB-15 Buffer

Electronic Tuner

AB/Y Switcher

Amp 1

Amp 2

USING THE DRAG CONTROL

Radial’s DRAG™

load correction allows you to dial in just the

right amount of loading for your pickups to create the same

impedance relationship as when plugging directly into your

amplifier. Start with the DRAG™ control set to the 12 o’clock

position. Turning it clockwise will brighten the tone while

turning it counter-clockwise will darken it. Strum a chord and

slowly turn the DRAG control until the tone sounds right to

you. Use your guitar pick like a screwdriver to easily adjust

the recessed control.

StageBug™ SB-15 Tailbone

USER GUIDE

To view the 3-year transferable warranty details and

product specifications please visit www.radialeng.com

Produkt Specifikationer

Mærke:	Radial Engineering
Kategori:	Ikke kategoriseret
Model:	StageBug SB-15

Har du brug for hjælp?

Hvis du har brug for hjælp til Radial Engineering StageBug SB-15 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Radial Engineering Manualer

Radial Engineering PhazeQ Manual

18 Februar 2025

Radial Engineering J-Rak 8 Manual

11 Februar 2025

Radial Engineering Workhorse PowerStrip Manual

11 Februar 2025

Radial Engineering PreComp Manual

11 Februar 2025

Radial Engineering Tonebone PZ-Select Manual

11 Februar 2025

Radial Engineering Bones Hollywood Manual

23 December 2024

Radial Engineering 4-Play Manual

21 December 2024

Radial Engineering BigShot SW2 Manual

21 December 2024

Radial Engineering BigShot i/o Manual

21 December 2024

Radial Engineering Catapult Rack Manual

21 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Simrad Active Imaging HD (Thru-Hull) Manual

14 Juni 2025

Garritan Harps Manual

14 Juni 2025

Marshall CV-H20-HF Manual

14 Juni 2025

Aiphone IXW-MAA Manual

14 Juni 2025

Rival HM-743 Manual

14 Juni 2025

Lutec Avony Manual

14 Juni 2025

Giordani G-SAFE & PLAY Manual

14 Juni 2025

Gourmia GAF799 Manual

14 Juni 2025

Arendo 307503 Manual

14 Juni 2025

Hughes & Kettner Tube 100 Manual

14 Juni 2025