Rane AC 23 Manual

Rane Ikke kategoriseret AC 23

Læs gratis den danske manual til Rane AC 23 (18 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Rane AC 23, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/18

Manual-1

AC 23

ACTIVE CROSSOVER

OPERATORS MANUAL

AC 23 CONNECTION

Balanced/Unbalanced Inputs

The ¼" Input jacks on the AC 23 are TRS (tip-ring-

sleeve). We recommend connecting the AC 23 with a bal-

anced cable from the balanced output of a mixer or equalizer.

If a balanced output is not available, and the cable run is

less than ten feet (three meters), inserting an unbalanced ¼"

TS (tip-sleeve) plug works in most situations.

Unbalanced Outputs

The ¼" Output jacks on the AC 23 are unbalanced TS

(tip-sleeve). We recommend that cables to the amplifiers be

no longer than ten feet (three meters).

See the “Sound System Interconnection” RaneNote

included with this manual for more information on cabling

and grounding requirements.

QUICK START

This is an automatic crossover! By automatic, we mean that the AC 23 is smart enough to know whether you want to

run it as a two channel crossover, or as a single channel unit. It knows by the way the plugs are inserted how your system is

to be configured. However, just because it is automatic, doesn’t mean that it will not automatically confuse you when you

try to connect it in a bench test situation. Note: Labels above the controls refer to the unit being operated in the 2- or 3-

Way Stereo mode. Labels below the controls refer to the unit being operated in the 4- or 5-Way Mono mode.

Plugging a signal into the CHANNEL 1 INPUT and nothing into the CHANNEL 2 INPUT tells the unit that you are

running a single channel system in Mono 4- or 5-Way mode, and therefore sets the unit up to be a single channel device.

This can lead one to think that there are some dead channels in the unit when looking for output in places where there

shouldn’t be any. The even more automatically confusing part is the way that the Output connectors decide whether the unit

is a 4-Way or 5-Way crossover. It is actually rather straightforward.

To test the unit as a Mono 4-Way, first slide the CHANNEL 1 and 2 switches on the back to 3-WAY. Connect the

INPUT source to CHANNEL 1 only. Following the labels below the jacks, look at SUB OUT, then look at LOW OUT,

now go back to MID OUT, and then proceed to the HIGH OUT. So far, so good.

To test the AC 23 as a Mono 5-Way, the only precaution required is there must be a “dummy” plug (¼" unconnected

plug) inserted into the HI MID OUT to program the crossover properly. When you reach the point where you want to

measure the output of the channel with the dummy in it, simply remove it and insert your test output plug in that location.

When operating the AC 23 as a Stereo 3-Way, follow the diagram on page Manual-5, reading the labels above the jacks

and controls. To drive both Channels with a mono signal, connect only to the CHANNEL 2 INPUT. This approach is the

same as if you used a wye cable to both Inputs.

The AC 23B is available as a fully balanced output version equipped with XLR connectors (for inputs and outputs)

instead of the ¼" jacks. If you are connecting to balanced amplifiers from the AC 23 or are running crossover output cable

lengths greater than 10 feet (or 3 meters), we highly recommmend you purchase an AC 23B.

Never connect anything except an RS 1 or other approved Rane AC power supply to the thing that looks like a

telephone jack on the rear. This is an 18 VAC center-tapped power unit. Consult the Rane factory for replacement or

substitution.

WEAR PARTS: This product contains no wear parts.

Manual-2

FRONT PANEL: STEREO 2-WAY CONFIGURATION

Observe the labels screened above the controls for stereo operation.

NOTE: In the 2-Way mode, the AC 23 crossover range is from 190 Hz to 7 kHz. The model AC 22 crossover in

stereo 2-Way mode is recommended when the crossover point needs to be outside of this range.

* Not used in 2-Channel 2-Way Mode

햲 POWER switch: Two guesses.

햳 POWER indicator: When this yellow LED is lit the unit is ready to operate.

햴 CHANNEL 1 MASTER LEVEL control: Sets the overall Level of Channel 1 without altering the relative settings of the

Low and High frequency Outputs. Unity gain for all level controls is at “7”.

햵 LOW LEVEL control: Sets the Level of signal going to the Low Frequency output in this channel. Refer to ‘Setting the

Output Level Controls’ on page Manual-15.

햶 LOW MUTE switch: When pressed to the in position, all signal is removed from the Low Frequency Output. This eases

tune-up procedures as described on pages Manual-11-16.

햷 LOW DELAY control: Adds from 0 to 2 ms of time Delay to the Low Frequency Output only. This allows a low fre-

quency driver to be electronically phase-aligned with a mid frequency driver whose diaphragm is situated behind the low

frequency diaphragm. Refer to ‘Time Delay Adjustment Procedure’ on page Manual-10.

햸 LOW/HIGH crossover frequency selector: This 41-detent selector sets the crossover frequency between the Low and

High frequency Outputs. Refer to ‘Selecting Crossover Frequencies’ on page Manual-10.

햹 HIGH LEVEL control: Sets the Level of signal going to the High frequency Output only.

햺 CHANNEL 2 MASTER LEVEL control: Sets the overall Level of Channel 2 without altering the relative settings of the

Low and High Outputs.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	AC 23

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane AC 23 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JILONG JL097205NPF Manual

14 September 2025

Brandson 306570 Manual

14 September 2025

Nedis PIM30012EGY Manual

14 September 2025

Neutrik SCD-W Manual

14 September 2025

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025