Rane SM 26B Manual

Rane Ikke kategoriseret SM 26B

Læs gratis den danske manual til Rane SM 26B (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Rane SM 26B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Manual-1

OPERATORS MANUAL SM 26B

SPLITTER MIXER

SM 26B CONNECTION

When connecting the SM 26B to other components in

your system for the first time, leave the power supply for last.

This gives you a chance to make mistakes and correct them

before damage is done to anything fragile.

As you have no doubt noticed, all Inputs and Outputs on

the SM 26B’s rear panel are ¼" connectors. The Inputs and

Outputs are active balanced on Tip-Ring-Sleeve (TRS) jacks

which allow the flexibility of connecting in either a balanced

or unbalanced fashion. If unbalanced operation is your

preference, the simplest way to accomplish this is through the

use of tip and sleeve ¼" connectors. The ring is not essential

unless balanced operation is required. You should be aware

that if you are running unbalanced and using TRS connectors

with both ring and tip, the ring and sleeve must be shorted

together. Failure to do so on the inputs results in a gain loss of

6 dB.

Balanced operation requires that TRS plugs be used. The

tip is hot (+), the ring is return (–) and the sleeve is ground.

RaneNote 110, “Sound System Interconnection” (included

here) contains some great pictures to aid your interconnect

ventures.

QUICK START

Realizing that in most areas there are laws against reading owners manuals, and that reading them under the blankets at

night with a flashlight makes you feel stupid, we therefore provide this brief, yet informative, description of how to use the

SM 26B just in case your batteries are low and your mother is about to come in the room.

To achieve a quick understanding of the SM 26B, think of it as a six channel mixer with faders and pans only. Or think

of it as a 2-to-6 channel splitter with output level controls and a mix knob (to control how much of which input goes to

which output). If you get that, you may stop here as long as you know how to hook up the power supply.

As a six channel mixer, MONO IN 1 through 6 may be placed on the Right or Left bus or both, in any amount. The

respective LEVEL knobs on the front of the unit serve as the mixer’s faders, the adjacent PAN controls place the channel’s

signal into the stereo field. As an effects mixer or line level expander for a larger mixer, set up the LEVELS and adjust the

PANS. The MASTER OUTPUT LEVEL adjusts the overall level of the mix at the Master Outputs.

As a splitter, place one or both input signals into the LEFT and/or RIGHT Inputs. Select the Input(s) to be placed at

each of the six MONO OUTs by rotating the MIX/PAN control to the proper position. Set the individual CHANNEL

LEVEL controls for proper output level. The MASTER INPUT LEVEL control on the front adjusts both Right and Left

Input signal levels together.

Never connect anthing except an RS 1 or other approved Rane AC power supply to the red thing that looks like a

telephone jack on the rear of the SM 26B. This is an AC input and requires some special attention if you do not have an

operational power supply exactly like the one that was originally packed with your unit. See the full explanation of the

power supply requirements elsewhere in this manual.

WEAR PARTS: This product contains no wear parts.

Manual-2

FRONT PANEL DESCRIPTION

햲 POWER switch: Two guesses ......

햳 POWER indicator: When this yellow LED is lit, the SM 26B is ready to go.

햴 MASTER OUTPUT LEVEL controls the amount of signal at the MIX OUTPUT jacks. It does not affect the level of any

of the six MONO OUTs. This control changes the gain of the output stages. This allows an increase in headroom to elimi-

nate overloading due to excessive combined signal from one or more Inputs. Range of gain is from Off to 0dB (unity). Refer

to the block diagram in the SM 26B Data Sheet and/or schematics.

햵 MONO INPUT LEVEL controls the Level of signal through each particular channel. When fed from the MONO IN jack,

each stage has a gain range from Off to +12 dB minimum, allowing level matching of -10 dBV equipment to +4 dBu gear.

When fed via the LEFT & RIGHT INPUT(s), these CHANNEL LEVEL controls automatically limit to a maximum of

unity gain to accommodate the +12dB available from the Left & Right Input gain stages.

햶 MIX/PAN serves two different functions:

MIX: When used as a SPLITTER, this controls the mix of Left and Right Master Input program to each Channel’s MONO

OUTPUT.

PAN: When used as a MIXER, this control pans the Mono Channel Input between the LEFT and RIGHT MIX OUTPUTS.

햷 MASTER INPUT LEVEL sets the gain of the Left & Right Master Input stages, with a range of Off to +12 dB. In the

splitting mode, this controls the Level of all Mono Channel Outputs at once (i.e., those which do not have a separate input).

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	SM 26B

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane SM 26B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025

AMX DVX-2250HD Manual

14 September 2025

AMX Vision² Manual

14 September 2025

AMX NMX-ENC-1100 Manual

14 September 2025

AMX UPC20+ Manual

14 September 2025