Rane SP 13 Manual

Rane Ikke kategoriseret SP 13

Læs gratis den danske manual til Rane SP 13 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Rane SP 13, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Manual-1

OPERATORS MANUAL SP 13

STICK PREAMP

QUICK START

The SP 13 accommodates the signals from two pickups from a Stick® instrument, where the pickups are wired to the

tip and ring of a standard stereo ¼" TRS (Tip, Ring, Sleeve) plug. You do not need internal preamps when using the SP 13.

1. Slide the Input Wiring switch to the correct position agreeing with your pickup wiring situation.

2. Turn the MAIN OUT LEVEL controls down.

3. Connect the SP 13 to your amplifier using the ¼" MAIN OUTPUTS or use the HEADPHONE jack.

4. Initially, turn the A and B INSTRUMENT GAIN TRIM controls half way up.

6. Move each LOW CUT slider to the top (15 Hz); center all EQ sliders; center the PAN sliders; leave the INVERT

pushbuttons out; and position the LEVEL sliders to “4”

7. Plug in the instrument to the INPUT jack on the front of the SP 13 with a stereo ¼" TRS cable.

8. Power up the SP 13, then turn on your amplifier.

9. Play your instrument and slowly turn up the MAIN OUT LEVEL controls. You should hear sound from your speakers.

If not, recheck all settings and wiring, and read the next few pages.

Never connnect anything except an approved Rane power supply to the red thing that looks like a telephone jack on the

rear of the unit. This is an AC input and requires special attention if you do not have a power supply exactly like the one

originally packed with your unit. See the full explanation of the power supply requirements elsewhere in this manual.

WEAR PARTS: This product contains no wear parts.

Manual-2

FRONT PANEL DESCRIPTION

 Stick® INSTRUMENT INPUT: is a stereo ¼" TRS (Tip-Ring-Sleeve) INPUT jack for use with a Stick instrument with

two pickups; Use a balanced or stereo ¼" shielded cable to connect your instrument to this Input. However, this also accepts

a mono input. When using a mono cable, signal is routed to the TIP selected by the Input Wiring Switch (see ).

 A & B Input OVERLOAD indicators: are useful in monitoring pickup level and initially in setting PICKUP GAIN TRIM

controls. These indicators light approximately 4 dB before actual clipping, so occasional flickering is okay, but they should

never be allowed to light steadily.

 Input wiring switch: allows choice of Input wiring. Either TIP=A and RING=B, or vice-versa.

 Input INSTRUMENT GAIN trims: set the proper Gain for each pickup. Range is from 6 dB minimum to 60 dB maxi-

mum.

 INVERT switches: Invert the polarity (phase) of the A pickup with respect to the B pickup. Either A or B PICKUPS may

be individually Inverted.

 LOW CUT frequency: adjusts the corner frequency of the LOW CUT (high-pass) filter from 15 Hz to 250 Hz. Use to

reduce unwanted low frequencies in either A or B Pickups.

 7-band graphic equalizer boost/cut controls: set the amount of boost/cut for each of the indicated bands in both Pickups

A and B. A grounded center detent guarantees flat response for filters not used.

 PICKUP A OUT control: adjusts the level of the AUX OUTPUT jack. This Output is independent of the LEVEL and

MAIN OUT LEVEL controls.

 PAN controls: for both PICKUPS A and B allow signal routing anywhere between MAIN OUT A and B.

 LEVEL controls: for both PICKUPS A and B set the overall Level of each signal.

 SEND A/B controls: adjust the amount of signal at each of the SEND jacks (to external signal processing).

 RETURN control: is a “stereo” Return. Controls the amount of A and B entering the RETURN jacks.

 MAIN OUT MUTE button: cuts off the signal to both A and B Main Outputs. Does not affect the Headphone Output. The

red LED indicates Muted Output.

 MAIN OUT A & B LEVELS: are concentric controls used to separately set the Main A & B Output Levels.

 MAIN OUT OVERLOAD indicator: monitors both A and B Main Outputs. An overload condition (within 4 dB of

clipping) on either Output causes this red indicator to light.

 HEADPHONE LEVEL: controls the volume of the HEADPHONE Output jack.

 POWER indicator: glows yellow when the proper power supply is connected and powered.

 Headphone jack: Accepts standard stereo headphones rated from 32-600 ohms equipped with a ¼" TRS plug.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	SP 13

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane SP 13 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Playtive IAN 304227 Manual

20 Juni 2025

Ciarra CBCS5931B Manual

20 Juni 2025

IFM PL1507 Manual

20 Juni 2025

LC-Power Integrator Pro LC6650B-SI V3.1 Manual

20 Juni 2025

Ciarra CBCS6903D Manual

20 Juni 2025

Curtis enGage II Manual

20 Juni 2025

Parkside HG10350 Manual

20 Juni 2025

Phoenix Gold ZDT-OPEL2 Manual

20 Juni 2025

Dahua Technology IVS-IP8000-E-GU1 Manual

20 Juni 2025

Icom IC-F29SR2 Manual

20 Juni 2025