RDL D-TPS7A Manual

RDL Ikke kategoriseret D-TPS7A

Læs gratis den danske manual til RDL D-TPS7A (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 4 anmeldelser. Har du et spørgsmål om RDL D-TPS7A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Twisted Pair Format-A

Modules D-TPS7A & D-TPP7A

Modules DS-TPS7A & DS-TPP7A

Format-A Passive Single Pair Sender

RDL





659 6

St.





Prescott, AZ., USA 86301





(928) 443-9391





FAX (928) 443-9392





www.rdlnet.com

 Stereo Audio Input Combined to Mono Output

 Input on Mini-jack

 Switch Selects which RJ45 Pair (A, B or C) is Fed

 Signal and Power Pair Pass-Through between TP CABLE RJ45 Jacks

 Passive Circuitry Does Not Require Power

 Galvanic Isolation through a Studio-Quality Transformer



Daisy-Chain with Single-Pair or Two-Pair Format-A Senders

The -TPS7A is a single-pair audio sending module compatible with RDL

Format-A twisted pair products. The front panel

features a single stereo mini-jack intended for stereo consumer line level audio sources. A studio-quality transformer

provides isolation between the audio source and the RJ45 TP CABLE.

The -TPS7A is a single-pair sender, feeding the input signal to the cable pair set on the rear-panel

switch during installation. This module drives only one cable pair, therefore a TP CABLE RJ45 jack is

provided to accept signals and power from other mic-level or line-level Format-A senders. Two other

single-pair senders may be chained to a TP CABLE jack, or a single two-pair sender may be

connected. If three single-pair senders are connected together, each sender must feed a different

pair: A, B or C. The -TPS7A must be set to feed pair A if it is connected together with an RDL two-pair

sender that feeds stereo audio on pairs B and C.

The -TPS7A is a passive module that does not require power to operate. If power is present on a

cable connected to a TP CABLE jack, that power is passed through to the modules connected to the

other TP CABLE jack.

The D-TPP7A is the same as the D-TPS7A but includes a connection for composite video pass through.



D-TPS7A or DS-TP76A Format-A Audio Sender



Video Monitor Pass-Through



Available in RDL White/Gray (D-TPP7A)



Available in Stainless Steel (DS-TPP7A)

D-TPS7A

DS-TPS7A DS-TPP7A D-TPP7A

STEP 1: Set the PAIR selector so the module is driving the desired pair A, B or C of the Format-A cable. If the module is connected

together with one or two other single-pair senders, each sender must be set to a different pair. If connected together with a

two-pair

sender, the switch must be set to pair A.

STEP 2: Connect a high-impedance unbalanced audio source to the input (-10 dBu 3.5 mm mini-jack).

STEP 3: Connect the twisted pair cable(s) and mount the module.

TWISTED PAIR Format-A

Model D-TPS7A & D-TPP7A

Model DS-TPS7A & DS-TPP7A

Format-A Passive Single-Pair Sender

Installation/Operation

Declaration of Conformity available from rdlnet.com.

Sole EMC specifications provided on product package.

Specifications are subject to change without notice.

Radio Design Labs Technical Support Centers

U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506

Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287

891-4645A

TYPICAL PERFORMANCE

Input: 3.5mm mini-jack, unbalanced stereo combined to mono

Input Level: -10 dBV, +22 dBu max

Format-A Signal Pair Used: Switch-selectable A, B, or C (rear-panel switch)

Format-A Input: RJ45 TP CABLE

Output: RJ45 TP CABLE, RDL TP Format-A

Frequency Response: 20 Hz to 20 kHz (±0.5 dB)

THD: < 0.1% (50 Hz to 20 kHz); <0.001% (1 kHz typ)

Power Requirement: Passive

Dimensions: 1.6” (4.06 cm) W; 4.11” (10.45 cm) H; 1.89” (4.8 cm) D

(1) + White / Green

(2) – Green

(3) + White / Orange

(4) – Blue

(5) + White / Blue

(6) – Orange

(7) + White / Brown

(8) – Brown

Pair A: Audio +4 dBu

Pair B: Audio +4 dBu

Pair C: Audio +4 dBu

Pair D: Power +24 Vdc

Tab on bottom of connector

RJ45 Standard wiring

RJ45 conductor colors shown are for 568A standard. The 568B standard may be used if the connectors at both ends of the cable are wired identically.

Produkt Specifikationer

Mærke:	RDL
Kategori:	Ikke kategoriseret
Model:	D-TPS7A

Har du brug for hjælp?

Hvis du har brug for hjælp til RDL D-TPS7A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret RDL Manualer

29 August 2024

29 August 2024

25 August 2024

18 August 2024

10 Juli 2024

20 Februar 2024

27 September 2023

31 Maj 2023

27 November 2022

22 November 2022

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Rival FRRVSC500 Manual

14 Juni 2025

Marshall AR-DM61-BT Manual

14 Juni 2025

Berkel Suprema Salumeria PES315 Manual

14 Juni 2025

Levenhuk LabZZ F1 Manual

14 Juni 2025

AVM FRITZ!Smart Energy 200 Manual

14 Juni 2025

Aiphone AC-2DM-B Manual

14 Juni 2025

Levenhuk LabZZ FL5 Manual

14 Juni 2025

Mountfield Multiclip 501HP Manual

14 Juni 2025

Bopita Universal Manual

14 Juni 2025

ENTES GEMO-10-4G Manual

14 Juni 2025