RDL TX-TPR2A Manual

RDL Ikke kategoriseret TX-TPR2A

Læs gratis den danske manual til RDL TX-TPR2A (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 4 anmeldelser. Har du et spørgsmål om RDL TX-TPR2A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

TWISTED PAIR FORMAT-A

Models D-TPR2A, DB-TPR2A, DS-TPR2A

Format-A Two-Pair Receivers

• Two Unbalanced -10 dBV Phono Jack Audio Outputs

• L (Left) Output From Pair B; R (Right) From Pair C

• Signal and Power Pair Pass-Through on RJ45s

• Remote Powering through Twisted Pair Cable

• Fused Local Power Feeds all Connected Modules

• Local Power Input on Terminal Block

• Blue LED Indicates Module is Powered

• Daisy-Chain with Additional Format-A Receivers

• Studio-Quality Precision Active Balanced Circuitry

The D SERIES-TPR2A modules are two-pair audio receiving modules compatible with RDL Format-A twisted pair products. These modules are designed to be

mounted in wall boxes, cabinets or other enclosures that allow users to connect external equipment. The -TPR2A models mount in RDL WB-1U and WB-2U wall

boxes, or in standard U.S. electrical boxes. The D-TPR2A features a white front-panel laminate with gray lettering that matches RDL Decora©-style remote controls.

The DB-TPR2A features a black front-panel laminate. The DS-TPR2A is constructed of stainless steel to coordinate with RDL Decora-style stainless steel remote

controls in commercial/industrial installations.

APPLICATION: The D SERIES-TPR2A modules feature two RCA phono jack outputs, one for the left channel

output and one for the right channel. The audio signals received from pairs B and C of the twisted pair cable are

buffered to drive the output jacks at the standard -10 dBV consumer level.

This module receives signal from only two cable pairs, so the D SERIES-TPR2A modules have a second RJ45 jack

to connect cables to additional receiver modules. A separate single-pair receiver may be chained to the second

RJ45 jack. In addition to completing the reception of signals from all three FORMAT-A pairs, additional receivers

may be connected to the same twisted pair feed. The bridging input circuits used in all FORMAT-A twisted pair

receivers allow connection of up to 10 receiver outputs for each cable pair. The possibility of multiple receiver

locations adds enormous flexibility in the design of audio routing systems using RDL FORMAT-A products. The

power pair and all three audio pairs are fed through both rear-panel RJ45 jacks.

The D SERIES-TPR2A may be powered directly from a 24 Vdc power supply using the rear-panel detachable

terminal block. Local power connected to the module is also fed to all connected remote modules. The -TPR2A

may be remotely powered through the twisted pair cable from any other module, signal distributor or RDL power

inserter connected to the same twisted pair cable. Module power is indicated by a front-panel LED.

RDL FORMAT-A features superior audio performance that rivals or exceeds shielded wiring. Design simplicity,

ease of installation, unsurpassed flexibility, automatic fused power, exceptional hum rejection, low noise, and low

distortion provide designers and installers the optimum choice in economical twisted pair products.

RDL 



 659 6th St. 



 Prescott, AZ., USA 86301 



 



 (928) 443-9391 FAX (928) 443-9392 



 www.rdlnet.com

D-TPR2A DS-TPR2A DB-TPR2A

TWISTED PAIR FORMAT-A

Models D-TPR2A, DB-TPR2A, DS-TPR2A

Format-A Two-Pair Receivers

TYPICAL PERFORMANCE

Input: RDL FORMAT-A

Input Connection: RJ45

Format-A Signal Pairs Used (2): B (Left); C (Right)

Format-A Output: RJ45

Output: 100 Ω unbalanced

Output Connection: RCA Phono

Frequency Response: 10 Hz to 50 kHz (+/- 0.1 dB)

THD+N: < 0.005%

Noise below +4 dBu: < -90 dB

Crosstalk: < 90 dB (1 kHz); < 75 dB (20 Hz to 20 kHz)

Headroom above +4 dBu: > 18 dB

CMRR: > 80 dB (50 Hz to 150 Hz)

Indicator: Power In

Power Connections (2): Detachable terminal block; RJ45

Power Requirement: 24 Vdc @ 45 mA plus connected loads

Maximum Load Current: 155mA

Dimensions: 1.6" (4.06 cm) W; 4.11" (10.45 cm) H; 1.89" (4.8 cm) D

Mounting Box Minimum Depth: 2.4"

Declaration of Conformity available from rdlnet.com.

Sole EMC specifications provided on product package.

Specifications are subject to change without notice.

Installation/Operation

STEP 1: Connect 24 Vdc to the power input terminals if this module is not being powered through the twisted pair cable from another module, or if

this module is located an excessive distance from the next powered module on the cable. Note: The front-panel power LED will be illuminated if

this module is powered. If this module is powering other modules through the cable and if there is a wiring short, the short must be cleared then

power must be turned off to this module for 10 seconds to reset the internal protection circuit.

STEP 2: Connect the twisted pair cable coming from Format-A senders or distributors.

STEP 3: Connect the twisted pair cable feeding additional Format-A receiver(s), if any, and fasten the module in its mounting box.

891-4580C

Radio Design Labs Technical Support Centers

U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506

Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287

(1) + White / Green

(2) – Green

(3) + White / Orange

(4) – Blue

(5) + White / Blue

(6) – Orange

(7) + White / Brown

(8) – Brown

Pair A: Audio +4 dBu

Pair B: Audio +4 dBu

Pair C: Audio +4 dBu

Pair D: Power +24 Vdc

Tab on bottom of connector

RJ45 Standard wirin

RJ45 conductor colors shown are for 568A standard. The 568B standard may be used if the connectors at both ends of the cable are wired identically.

TP CABLE

24 VDC

D SERIES-TPR2A

TWISTED

PAIR CABLE TWISTED

PAIR CABLE

REQUIRED CONNECTION OPTIONAL CONNECTION

NOTE: Connect a 24 Vdc power supply

to the module if power is not being

supplied through a twisted pair cable

from a connected module.

24 Vdc power

connection

(see note)

Connection from Single-Pair, Two-Pair

or Three-Pair Senders (direct, or via an

RDL Twisted Pair Power Inserter)

Connection from Format-A Distributor

Connection from other Format-A

Receivers

Connection to additional Format-A

Receiver(s)

Connection to Format-A Receiver(s) via

an RDL Twisted Pair Power Inserter

Connection to Format-A Distributor Input

Produkt Specifikationer

Mærke:	RDL
Kategori:	Ikke kategoriseret
Model:	TX-TPR2A

Har du brug for hjælp?

Hvis du har brug for hjælp til RDL TX-TPR2A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret RDL Manualer

28 September 2025

29 August 2024

29 August 2024

25 August 2024

18 August 2024

10 Juli 2024

20 Februar 2024

27 September 2023

31 Maj 2023

27 November 2022

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vestil AHA-15-12-12-PNU Manual

1 Oktober 2025

Vestil SY-168436-L Manual

1 Oktober 2025

Vestil AHS-4-15-7-VG Manual

1 Oktober 2025

Vestil BOLPP-62-6.5 Manual

1 Oktober 2025

Vestil AWR-G-28-8A Manual

1 Oktober 2025

Structural Concepts Fusion GMS4H Manual

1 Oktober 2025

Vestil AHSN-2-10-16 Manual

1 Oktober 2025

Draper Expert 19370 Manual

1 Oktober 2025

Structural Concepts Reveal NE3613DSV Manual

1 Oktober 2025

Vestil AHSN-6-15-16-TLC Manual

1 Oktober 2025