Renkforce C4L6400-TWP-P Manual

Renkforce Ikke kategoriseret C4L6400-TWP-P

Læs gratis den danske manual til Renkforce C4L6400-TWP-P (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Renkforce C4L6400-TWP-P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Technical Support Contact

Address : 2F, 628, Donghang-ri, Yangseong-myeon, Anseong-Si, Gyeonggi-Do, Korea.

Tel : Fax : +82 70 4100 8847 / +82 31 674 6608

E-mail : info@c4line.com

Website : www.c4line.com

C4L6400-TWP-P Transceiver Field Application

C4L6400-TWP-P transceivers are used to extend the Ethernet IP signals via Cat 5E , Cat 6 or 2 wire

cable in the existing UTP network in building.

C4L6400-TWP-P transceiver could reduce the cabling costs to upgrade from the installed analog video

cameras to Mega-pixel grade IP cameras with the inexpensive UTP cabling.

For the other field applications, C4L6400-TWP-P transceivers could be applied to connect, distribute and

convert the IP devices(IPTV, VOIP Phone, Wireless AP, etc.) signals via the UTP cable with 128bit AES

Encryption and guaranteed QoS for loss sensitive application.

C4L6400-TWP-P Transceiver

Quick Start Guide

• Both transceivers are now in . They will find each Joining mode

other and establish encrypted communication. In about 10 seconds,

the TWP LEDs on both transceivers will illuminate (blinking or steady

on), indicating a successful . Join

C4L6400-TWP-P connection diagram

C4L6400-TWP-P Installation Steps

Step 1. Hardware Check and Preparation

• Please check the product physical defects. If you find the defects, do not operate the product.

• Prepare 1) Network cable, 2) Extend UTP cable, 3) 48VDC Power supply to C4L6400-TWP-P

units. (Please check the cable short, Spec. and connection status)

Step 2 . Installation

• Use one C4L6400-TWP-P transceiver at each end of the UTP. Up to four remote transceivers

and coax runs may be connected to a fifth transceiver at the control room using Ethernet splitters.

• Connect a 48V DC power supply into one of the transceivers to provide power to the entire system,

including the cameras.

• Single camera loads up to 40 watts, or four 10 watt cameras are supported by the 48VDC 60W

power supply.

• All transceivers are in Join Mode. They will find each other and establish basic level encrypted

communication.

If you use more than 1 master unit or large installation site, you should

follow the Un-joining and Joining steps as below.

Un-Joining and Joining Transceivers for Encrypted communication(Optional)

If you want to build enhanced encrypted communication Network Group to another, it must be returned

to an un-joined state.

Step 1.Un-Joining to build enhanced encrypted network

• Do this by applying 48VDC power, and pressing the small push-button (Grp) for 10 seconds until

the TWP and PoE LEDs illuminate and then go out, about one seconds. The transceiver is now

ready to be joined to build encrypted Network Group.

Step 2. Joining mode

• For more transceivers in an enhanced encrypted network, disconnect the joined transceiver from

grouped UTP cable and connect the new un-joined transceiver.

• On transceiver number 1, using the straightened paper-clip, momentarily depress the small push-

button (Grp). The PoE LED will blinking.

• Depress the same small push-button (Grp) on the second transceiver.

Step 3. Adding Transceivers (if required)

• Disconnect one of the transceivers and replace it with a new un-joined transceiver.

• Repeat step two to add additional transceivers to the same Network Group.

Power over Ethernet (PoE) Function

• C4L6400-TWP-P support IEEE 802.3af. and 802.3at. PoE.

• C4L6400-TWP-P support 40Watt local PoE for IP camera power supply.

C4L6400-TWP-P Installation Warnings

• Do not use the transceiver near the harsh (temperature, humidity, cabling quality) installation site.

• If transceiver flooded by water or other liquid materials, please turn off the power source and

disconnect all of cables from transceiver. And request to C4Line technical team for after service

asap.

• Do not use transceiver over 120 (50 ) temperature condition for transceiver’s operation ℉ ℃

performance and lifetime.

• Do not disassemble transceiver at a person’s service.

Produkt Specifikationer

Mærke:	Renkforce
Kategori:	Ikke kategoriseret
Model:	C4L6400-TWP-P

Har du brug for hjælp?

Hvis du har brug for hjælp til Renkforce C4L6400-TWP-P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Renkforce Manualer

Renkforce C4L6400-TWP Manual

15 August 2025

Renkforce RF-HSA-200 Manual

14 August 2025

Renkforce RBP-ALC100 Manual

14 August 2025

Renkforce RF-WAT-300 Manual

14 August 2025

Renkforce PM-01 Manual

19 Juli 2025

Renkforce RF-5976404 Manual

23 Juni 2025

Renkforce RF-USBF-690 Manual

20 Juni 2025

Renkforce RF-5976400 Manual

20 Juni 2025

Renkforce RF-USBF-101 Manual

19 Juni 2025

Renkforce RF-3374946 Manual

30 Maj 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Zhiyun MOLUS B500 Manual

2 September 2025

Murr Elektronik Emparro67 Manual

2 September 2025

Scheppach AWH-500FL Manual

2 September 2025

Fender Acoustic Preverb Manual

2 September 2025

Fender Engager Boost Manual

2 September 2025

Fender Level Set Buffer Manual

1 September 2025

Biltema 30-061 Manual

1 September 2025

Scheppach C-AG125-X Manual

1 September 2025

Scheppach BCH5200PB Manual

1 September 2025

Omnires Siena SN7340 Manual

1 September 2025