Ridgid 445R Manual

Ridgid Håndværktøj 445R

Læs gratis den danske manual til Ridgid 445R (2 sider) i kategorien Håndværktøj. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Ridgid 445R, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

WARNING

Read and understand these instructions, and the

warnings and instructions for all equipment and

material being used before operating this tool to

reduce the risk of property damage or serious

personal injury.

SAVE THESE INSTRUCTIONS!

NOTICE Selection of appropriate materials and installation, joining and

forming methods is the responsibility of the system designer and/or

installer. Selection of improper materials and methods could cause system

failure.

Stainless steel and other corrosion resistant materials can be contaminated

during installation, joining and forming. This contamination could cause

corrosion and premature failure. Careful evaluation of materials and

methods for the specific service conditions, including chemical and

temperature, should be completed before any installation is attempted.

If you have any questions concerning this RIDGID

® product:

• Contact your local RIDGID distributor.

• Visit RIDGID.com to find your local RIDGID contact point.

•

Contact Ridge Tool Technical Service Department at rtctechservices.

com, or in the U.S. and Canada call (800) 519-3456.

Description

The RIDGID® Precision Flare Tools are designed to form flares on steel,

stainless steel, hard copper and brass tubing. The flare tools use an

eccentric, needle bearing mounted flare cone to form the flare with less

effort through a rolling action.

Precision Ratcheting and Non-Ratcheting Flare Tools have a clutch which

automatically releases to iron and smooth the flare. The ratcheting flare

tools include a reversible ratchet built into the feed screw handle.

Precision Ratcheting Flare Tools

Max. Tube Wall Thickness 0.035” (0.9 mm) ..................

Inspection/Maintenance

Clean equipment, including handle to aid inspection and improve control.

Inspect the flare tool for proper assembly, completeness, binding, wear or

damage. Feed screw and clamp screw should move freely. If any problems

are found, do not use until corrected. Only use with the assembled flaring

bar – do not remove or interchange flaring bars to insure compatibility.

Lubricate screws and flaring bar hinge with a light weight general purpose

lubricating oil. Wipe off any excess oil.

Set Up/Operation

1. Make sure tube end is cut square, reamed and free of burrs.

2. Loosen feed screw and clamp screw. Slide yoke to the hinged end of

flaring bar. For the ratcheting flare tool, the ratcheting direction can

be changed by rotating the reversing cap.

3. Open the flaring bar. If the flaring bar sticks closed, tighten clamp

screw to force the flaring bar open.

4. Insert tube into proper size opening and close the flaring bar. Place

the tube end even with top of flaring bar.

Flare diameter can be adjusting by placing tube end slightly above

or below the top of flaring bar (Figure 2).

Precision Flare Tools Instructions

5/17

051-454-640.07

EC42865

REV. B

The Emerson logo and RIDGID logo are registered trademarks of Emerson Electric Co. or RIDGID, Inc. in the U.S. and other countries.

All other trademarks belong to their respective holders.

Feed Screw

Handle

Flaring Bar

Yoke

Clutch

Ratchet Reversing Cap

Flaring Bar

Lines

Clamp

Screw

Arrow/Line

Alignment

Catalog Flare Weight

No. Model Type Sizes lb. kg

41162 377 37° SAE 3

/16, 1/4, 5/16, 3/8, 1/2, 5/8

, 3/4

” 4 1.6

50257 458MM 45° SAE 4, 4.75, 6, 8, 10, 12, 15, 16 mm 4 1.6

50262 458MMJ 45° SAE 4, 4.75, 6, 8, 10, 12, 15, 16 mm 4 1.6

41177 458 J 45° SAE 1

/8, 3/16, 1/4, 5/16, 3/8, 1/2

, 5/8

, 3/4” 3.3 1.5

68302 456 J 45° R410A 1

/4, 5/16, 3/8, 1/2, 5/8, 3/4” 3.3 1.5

Catalog Flare Weight

No. Model Type Sizes lb. kg

42153 445R 45° SAE 1/4, 3/8, 1/2, 5/8, 3/4” 3.3 1.5

83037 458R 45° SAE 1/8, 3/16, 1

/4, 5/16

, 3/8, 1/2, 5/8, 3/4” 3.9 1.7

70677 456R 45° R410A 1/4, 5/16, 3

/8, 1/2, 5/8, 3/4

” 3.6 1.6

Tube A – Increase Flare Diameter – Slightly Above

Tube B – Standard Flare – Even with Top

Tube C – Decrease Flare Diameter – Slightly Below

Figure 1 – Precision Ratcheting Flare Tools

Specifications

Precision Non-Ratcheting Flare Tools

Figure 2 – Tube Placement in Flare Bars

5. Slide yoke over tube to be flared. Align the arrow on the yoke with

the appropriate line on the flaring bar (Figure 1).

Securely tighten clamp screw into the dimple in the side of the flaring

bar, closing the flaring bar onto the tube.

6. Turn/ratchet the feed screw handle to bring the flare cone in contact

with the end of the tube. Continue to turn/ratchet the handle to form

the flare. Once the clutch releases, turn the handle at least two more

full rotations to ensure a uniform, smooth flare surface.

7. Loosen the feed screw to retract the flare cone.

8. Loosen clamp screw. Slide yoke to the hinged end of flaring bar.

9. Open the flaring bar. If the flaring bar sticks closed, tighten clamp

screw to force the flaring bar open.

10. Inspect the flare per the appropriate standard.

Produkt Specifikationer

Mærke:	Ridgid
Kategori:	Håndværktøj
Model:	445R

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid 445R stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Håndværktøj Ridgid Manualer

15 August 2024

14 August 2024

10 August 2024

9 August 2024

Håndværktøj Manualer

Nyeste Håndværktøj Manualer

25 November 2025

24 November 2025

24 November 2025

23 November 2025

6 November 2025

Nedis MAGLE1WT Manual

3 November 2025

Klein Tools 3000CRKIT Manual

25 September 2025

Klein Tools 3007CR Manual

17 September 2025

Biltema 19-234 Manual

14 September 2025

Blaupunkt CL3010 Manual

8 September 2025