Rosieres RDM 101 IN Manual

Rosieres Emhætte RDM 101 IN

Læs gratis den danske manual til Rosieres RDM 101 IN (20 sider) i kategorien Emhætte. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Rosieres RDM 101 IN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/20

INSTRUCTIONS FOR INSTALLATION AND USE

MONTAGE- UND GEBRAUCHSANWEISUNG

INSTRUCTIONS POUR L'INSTALLATION ET L’UTILISATION

ISTRUZIONI PER L'INSTALLAZIONE E L’USO

INSTRUCCIONES PARA INSTALACIÓN Y USO

INSTRUÇÕES DE INSTALAÇÃO Y UTILIZAÇÃO

AANWIJZING VOOR GEBRUIK EN INSTALLATIE

ENGLISH

DESCRIPTION

The unit can be found in filtering hoods, exhaust hoods or in hoods with an outside motor.

In the Filtering hoods (Fig. 1)

the air and steam taken up by the unit are purified with carbon filters and returned to the environment through the aeration

grids on the side of the flue. WARNING: When using filtering hoods, both carbon filters and an air deflector must be used.

Located in the upper part of the pipe, this deflector recycles the air to the environment (Fig. 1A).

In the Exhaust hoods (Fig.2)

an exhaust duct conveys the steam and cooking odors directly outside through the wall/ceiling. Therefore they do not

require carbon filters.

In the hoods with an outside motor (Fig. 3), a vacuum suction unit must be connected; this exhaust

will operate separately, conveying the exhaust air through the unit. Only use vacuum units suggested in the original

catalogue.

INSTALLATION

To facilitate installation, before starting remove the grease filter/s: press inward on the clamp at the handle and pull the

filter downward (Fig. 4).

Installation on the wall (Fig. 5): Using the special drilling template, drill the required holes in the wall. As previously

specified in the chapter “Warning” remember there must be a minimum of 650 mm between the bottom edge of the hood

and the stop of the stove. Secure the metal bracket (B) to the wall using the screws and plugs (bracket, screws and plugs

are all supplied with the unit). Use the 2 triangles cut into the bracket to position it precisely along the vertical axis of the

hood. Then set the hood onto the bracket. Adjust the horizontal position, shifting the hood to the right or left as needed

lining it up with the wall units. If the height of the hood also requires adjustment, use the special regulation screws (V)

(supplied). Once regulation has been completed, finish securing the hood with 4 more screws (M): mark the points for the

4 holes on the wall, remove the hood and drill (8mm diameter holes); then use the plugs and screws to complete installation.

Installation with rear panel (Fig. 6): The rear panel is positioned at the top of the stove, ﬂush against the wall. Rest the

lower edge of the panel behind the stove and anchor the upper edge to the wall using the two holes found on the panel.

Insert the screws and plugs provided (A). The unit is secured to the rear panel as though it were being installed on the wall:

use the supplied metal bracket (B) and the screws and plugs supplied with the panel.

Mount the plate of the electrical system fixing it with 3 screws and 2 metal washers (Fig. 7).

Securing the extension pipes:

Basic installation requirements: – Set the electrical power supply within the space covered by the decorative piping. – If

your unit is installed in an Exhaust hood or in a hood with outside motor, prepare the air exhaust hole.

When installing exhaust hoods and hoods with outside motor, to achieve the best possible conditions use an air exhaust

pipe that : is as short as possible, has a minimum of curves (maximum angle: 90°), is made of a material that complies

with the standards (which vary from nation to nation) and iv) is smooth on the inside. It is also advisable to avoid any drastic

changes in pipe section (diameter: 150 mm).

Adjust the width of the extension pipe support bracket (W) using screws A indicated in Fig. 8. Then use the plugs and

screws provided to secure it to the ceiling. Make certain it is aligned with the hood. For filtering hoods, the air exhaust grids

are positioned in the upper part (Fig. 9). For exhaust hoods, turn the upper pipe over so that the air exhaust grid is in the

lower section (Fig. 10).

Exhaust hoods and hoods with outside motors: Connect the hood flange to the exhaust hole in the wall/ceiling using a

flexible pipe.

Only for models with outside motor (Fig. 11): plug the hood into the outside control unit using the special

terminal block: remove wire clamp A and lid B from the wiring junction box. Secure the wire connecting the control unit

to terminal C. Then replace wire clamp A and lid B on the wiring junction box. The other end of the wire is secured to the

terminal block on the outside control unit.

Plug in the hood. Insert the extension pipes setting them on the hood; extend

the upper pipe to the ceiling and secure with the 2 screws (G) - Fig. 12.

Filtering hood: Secure the deflector to the upper pipe using the 4 special screws (provided) – Fig. 13; hook up the flexible

pipe (diameter: 125) to the deflector. Install the reduction (provided) on the hood air outlet point (Fig. 14). Take the 2

assembled extension pipes and set them on the hood; extend the upper pipe to the ceiling and secure with the 2 screws

(G) - Fig. 12.

Extend the lower pipe taping it in place and then connect the flexible pipe to the hood reduction. Plug in the

hood. Extend the lower pipe downward setting it against the hood. Install the carbon filter by pressing the 2 tabs on the filter

down into the special housing (Fig. 15) and rotating upward.

OPERATION

Depending on the model, the unit is equipped with the following commands:

Commands shown in Fig. 16: Button A = turns the lights on/off. Button B = turns the TIMER on/off: press once to turn

the timer on, therefore, after 5 minutes, the motor cuts out (at the same time the selected speed blinks on the display); the

timer remains on if the motor speed is changed. Display C = - indicates the selected motor speed (from 1 to 4); - indicates

Timer On when the number blinks; - indicates Filter Alarm when the central segments is on or blinking.

Button D = makes the motor work (at the last speed selected); pushing the button again, the speeds of the motor are

sequentially selected from 1 to 4; keeping this button pressed for about 2 seconds shuts down the motor.

Button R = resets the anti-grease filters or charcoal filters; when the filter alarm appears (i.e. when the central segment

on the display goes on), the anti-grease filters must be cleaned (30 hours of operation); when the central segment starts

Produkt Specifikationer

Mærke:	Rosieres
Kategori:	Emhætte
Model:	RDM 101 IN

Har du brug for hjælp?

Hvis du har brug for hjælp til Rosieres RDM 101 IN stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Emhætte Rosieres Manualer

Rosieres RHP67000/1LI Manual

31 August 2025

Rosieres RHP97000/1LP Manual

30 August 2025

Rosieres RDD9800/1B/1 Manual

30 August 2025

Rosieres RHP67000/1LP Manual

30 August 2025

Rosieres RHP97000/1LI Manual

30 August 2025

Rosieres RBVSI 985 IN Manual

7 August 2025

Rosieres RHT 6300/1LRB Manual

7 August 2025

Rosieres RHP67000 Manual

4 Januar 2025

Rosieres RHT6300/1LPN Manual

14 December 2024

Rosieres RBS 93680/2 IN Manual

14 December 2024

Emhætte Manualer

Nyeste Emhætte Manualer

Caple FGC720 Manual

30 September 2025

Caple ST524 Manual

29 September 2025

Caple TSCH901 Manual

29 September 2025

Caple ZEL900GM Manual

29 September 2025

Caple TBU521 Manual

29 September 2025

Caple CE903SS Manual

29 September 2025

Kernau KBH 0761 X Manual

29 September 2025

Caple CGC911 Manual

29 September 2025

Caple FGC920 Manual

29 September 2025

Siemens LI23030 Manual

29 September 2025