Rosieres RT 923/1 Manual

Rosieres Emhætte RT 923/1

Læs gratis den danske manual til Rosieres RT 923/1 (10 sider) i kategorien Emhætte. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Rosieres RT 923/1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

WARNING

--------------------------------------------------------

The distance between the hob and the lower

part of the hood must be at least 65 cm.

The air collected must not be conveyed

into a duct used to blow off smokes from

appliances fed with an energy other than

electricity (central heating systems, ther-

mosiphons, water-heaters, etc.).

Comply with the official instructions provided

by the competent authorities in merit when

installing the disposal duct. In addition,

exhaust air should not be discharged into

a wall cavity, unless the cavity is designed

for that purpose.

The room must be well aerated in case a

hood and some other heat equipment fed

with an energy other than electricity (gas,

oil, coal heaters, etc) operate at the same

time. In fact the intake hood, disposing of

air, could create a vacuum in the room.

The vacuum should not exceed 0,04mbar.

This prevents the gas exhausted by the

heat source from being intaken again. It is

therefore advisable to ensure the room

contains air taps able to ensure a steady

flow of fresh air.

Check the data label inside the

appliance; if the symbol ( ) is printed,

read the following: this appliance has

such technical particulars that it

belongs to class II insulation, therefore

it must not be earthed.

The following warning is valid in the United

Kingdom only: as the colours of the wires

in the mains lead of this appliance may not

correspond with the coloured markings

identifying the terminals in your plug,

proceed as follows:

– the wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black;

– the wire which is coloured brown must

be connected to the terminal which is

marked with the letter L or coloured red.

– terminal of a three-pin plug.

Check the data label inside the applian-

ce; if the symbol ( ) is NOT printed,

read the following: ATTENTION: This

English

appliance must be grounded. When

making the electrical connections, check that

the current socket has a ground connection.

The following warning is valid in the United

Kingdom only: as the colours of the wires

in the mains lead of this appliance may not

correspond with the coloured markings

identifying the terminals in your plug,

proceed as follows:

– the wire which is coloured green and

yellow must be connected to the terminal

in the plug which is marked with the letter

E or by the earth symbol [ ], or coloured

green or green and yellow;

– the wire which is coloured blue must

be connected to the terminal which is

marked with the letter N or coloured black;

– the wire which is coloured brown must

be connected to the terminal which is

marked with the letter L or coloured red.

When making the electrical connections,

check that the voltage values correspond

to those indicated on the data plate inside

the appliance itself.

In case your appliance is not furnished with

a non separating flexible cable and has no

plug, or has not got any other device ensu-

ring omnipolar disconnection from the elec-

tricity main, with a contact opening distance

of at least 3 mm, such separating device

ensuring disconnection from the main must

be included in the fixed installation.

Always switch off the electricity supply before

carrying out any cleaning or servicing

operations on the appliance.

USE

--------------------------------------------------------

Avoid using materials which could cause

spurts of flame (flambées) near the ap-

pliance.

When frying, take particular care to prevent

oil and grease from catching fire. Already

used oil is especially dangerous in this re-

spect. Do not use uncovered electric grates.

To avoid possible risks of fire always comply

with the indicated instructions when cleaning

anti-grease filters and when removing

grease deposits from the appliance.

MAINTENANCE

--------------------------------------------------------

Thorough servicing guarantees correct and

long-lasting operation.

Particular care must be paid to the anti-

grease filters which must be periodically

cleaned in relation to use (at least once

every two months). Remove the anti-

grease filters and wash them either by

hand or in the dishwasher using neutral

detergent. To take off the anti-grease filters:

at the handle, push the stop inwards and

pull the filter downwards (Fig.3); open the

trolley and take off the other filter doing the

same.

Any fat deposits should be removed from

the appliance periodically depending on

amount of use (at least every 2 months).

Avoid using abrasive or corrosive products.

To clean painted appliances on the outside,

use a cloth dipped in lukewarm water and

neutral detergent. To clean steel, copper

or brass appliances on the outside, it is

always best to use specific products,

following the instructions on the products

themselves. To clean the inside of the

appliance, use a cloth (or brush) dipped in

denatured ethyl alcohol.

DESCRIPTION

--------------------------------------------------------

The appliance can be a filtering version one,

a ducting version one or with an external

motor.

In the Filtering version (Fig. 1), the air and

vapours conveyed by the appliance are depu-

rated by charcoal ﬁlter and recirculated around

the room. ATTENTION: Using the hood as a

ﬁltering one it is necessary to use the char-

coal ﬁlter that puriﬁes the air sent back into

the room.

In the Ducting version (Fig. 2), cooking va-

pours and odours are conveyed straight out-

side by a disposal duct which passes through

the wall/ceiling. Use of charcoal ﬁlter is there-

fore unnecessary.

In the version with an External motor (Fig.

3), the appliance must be connected to an

ducting apparatus/motor which works on its

own using the appliance as a union for the air

to be scavenged. Use only motors pro-

posed in the original catalogue.

According to the model you have bought, the

appliance can include 1 or 2 motors. In the I

motor version the flange for the air to be

exhausted has not got a central position, but

it is slightly on the left.

INSTALLATION

--------------------------------------------------------

Before assembling, in order to manoeuvre the

appliance more easily, take off the anti-grease

filters: at the handle, push the stop inwards

and pull the ﬁlter downwards (Fig. 4); open the

trolley and take oﬀ the other ﬁlter doing the

same.

IMPORTANT: So as not to damage your

product, during installation USE ONLY THE

SCREWS PROVIDED. Make sure these are

used as shown in the following

instructions.

To compensate possible depth voids be-

tween the appliance and the wall, a plastic

SPACING BAR to be ﬁxed at the back of

the appliance by means of the three

screws A is included (Fig. 5). The 3 screws

A to be used are contained in the acces-

sory bag attached to the plastic spacing

bar. Cut the spacing bar according to the

distance to be adjusted.

Assembly under a pensile cupboard

The following operations are essential for

assembly:

– Install the wiring system

– Prepare the air venting hole if your

appliance is to be installed in the ducting

version or in the version with an external

motor.

In the Ducting version and in the version with

an External motor, to get optimal conditions

the air venting pipe should:

– be as short as possible.

– have the lowest number of bends (max

bende angle: 90°).

– be made of material approved by local

authorities (according to the State).

– have its inner side as regular and smooth

as possible.

It is moreover recommended to avoid drastic

changes of pipe cross section (recommended

diameter: 125 mm).

Fixation as indicated in Fig. 6:

Using the relative template make the 4

necessary fixing holes in the bottom of

the cupboard and cut the air venting hole.

For the version with an External motor,

make the electrical connection between

the hood and the external motor by means

of the proper terminal board (Fig. 8): take

oﬀ the cable clamp A and the cover B of

Produkt Specifikationer

Mærke:	Rosieres
Kategori:	Emhætte
Model:	RT 923/1
Type:	Indbygget under
Bredde:	900 mm
Dybde:	380 mm
Højde:	170 mm
Produktfarve:	Sølv
Antal hastigheder:	3
Motoreffekt:	200 W
Lampetype:	Halogen
Støjniveau:	58 dB
Pæreeffekt:	20 W
Antal lyskilder:	2 pære(r )
Maksimal ekstraktionseffekt:	260 m³/t
Fedtfilter type:	Metal
Antal motorer:	2
Indbygget kapacitet:	Ja
Antal filtre:	4 stk