Rupert Neve Designs R6 Manual

Rupert Neve Designs Ikke kategoriseret R6

Læs gratis den danske manual til Rupert Neve Designs R6 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 61 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 31 anmeldelser. Har du et spørgsmål om Rupert Neve Designs R6, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Six Space 500 Series Rack

Thank you for your purchase of the R6: Six Space 500 Series Rack. Everyone at Rupert Neve Designs

hopes you enjoy using this tool as much as we have enjoyed designing and building it.

Usage Notes

The R6 has 6 x 500 series slots, with ample power, and a full complement of XLR, TRS and DB-25 I/O

in a portable steel chassis. To use the R6, carefully slide each 500 series module in such that the edge

connector ts snuggly into the slot in the back, and tighten both front panel screws for each module.

The current draw meter will display the total current being used by the installed modules. Channels

7 & 8 do not correspond to a module slot, so the connectors are available to access channels 7-8 of a

connected DB-25 cable. These can also be used to convert the jack type (i.e from DB-25 to XLR, or

from TRS to DB-25)

Link

To enable linking between modules, reset the corresponding jumper located by the card slots to the

LINK position. The linking function is set in pairs so that you can link channels 1-2, 3-4, and 5-6. The

link function is typically used to link the VCA circuitry of compressors (such as our 543 module). Most

other types of units are not linkable unless specically noted by the manufacturer.

R6 Specications

DC Voltage to Units +/-16VDC and +48VDC for phantom power

Max Current 1000mA for modules, 150mA for 48V phantom power

Power Requirements 100-240VAC, 50/60Hz, 50 Watts

Weight 9.5lbs

Dimensions 13” long x 7.5”wide x 5.5” high

Front / Back Panel

R6: Six Space 500 Series Rack

Current MeterLink JumperCard Slot

There are three link jumpers,

which can be individually set

to allow linking on Channels

1-2, 3-4, and 5-6

The current meter monitors

the current draw on the

power supply

Each card slot is designed to

fit a standard 500 series

module

Channel 1-6 I/O

Channel 7-8 THRU I/OIEC Input

You can use the channel 7-8

connections access channels

7-8 on a connected DB-25

cable, or to switch between

TRS and XLR

Each channel has a multitude

of I/O options with XLR, TRS

and DB-25

The IEC power input accepts

100-240VAC, 50/60Hz input

with a 50 Watt draw

Produkt Specifikationer

Mærke:	Rupert Neve Designs
Kategori:	Ikke kategoriseret
Model:	R6

Har du brug for hjælp?

Hvis du har brug for hjælp til Rupert Neve Designs R6 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rupert Neve Designs Manualer

Rupert Neve Designs MBT Manual

27 August 2024

Rupert Neve Designs Satellite 5059 Manual

15 August 2024

Rupert Neve Designs R10 Manual

12 August 2024

Rupert Neve Designs R6 Manual

9 August 2024

Rupert Neve Designs RNDI-S Manual

4 August 2024

Rupert Neve Designs 5059 Manual

27 Juli 2024

Rupert Neve Designs MBC Manual

19 Juni 2024

Rupert Neve Designs 535 Manual

4 April 2024

Rupert Neve Designs 5052 Manual

31 December 2023

Rupert Neve Designs Newton Channel Manual

15 December 2023

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Alto-Shaam 200-HW/D643 Manual

16 September 2025

Turbo Air PRO-50H Manual

16 September 2025

16 September 2025

16 September 2025

16 September 2025

16 September 2025

Vitammy Autoband 5 Manual

16 September 2025

DeLOCK 91739 Manual

16 September 2025

Alto-Shaam 100-HW/D643 Manual

16 September 2025

Turbo Air M3H47-2-G Manual

16 September 2025