Sana EUJ-828 Manual
Læs gratis den danske manual til Sana EUJ-828 (24 sider) i kategorien Juicer. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Sana EUJ-828, eller vil du spørge andre brugere om produktet?
Side 1/24

USER MANUAL
SANA JUICER EUJ-828

02
04
06
07
08
10
12
13
14
15
16
18
19
20
22
Safety precautions
Parts and accessories
How to disassemble the juicing chamber How to
prepare produce / Strainer types
How to assemble for juicing
How to assemble for making ice cream
How to attach the juicing chamber to the body
How to use : For juicing / ice cream
How to use control lever by mode
How to use control lever by ingredients (Juicing)
How to clean
Precautions while juicing
If the auger stops during juicing
Before requesting a repair
Product specifications
01 Read the instructions carefully before using.
02 Keep these instructions somewhere easily accessible.
03 Use only with 230-240 V AC power supply.
04 Design and product development may be upgraded without notice.
05 Any quality improvements are subject to change without notice.
EUJ-828 ( For Household Use On
ly / Warranty Included )
CONTENTS

02
Safety precautions
• Do not plug or unplug with wet hands. It may cause electric shock or injury.
• Only use 230 - 240V AC power. Incorrect voltage may cause electric shock or
fire. Motor damage can occur with incorrect voltage.
•
Plug in the power cord correctly and push it firmly in a power outlet. Failure
to do so may cause an electric shock or a fire.
• If the power cord is damaged, it may only be replaced by an authorized
service person. Using a damaged power cord can result in electric shock or fire.
• Do not disassemble, attempt to repair, or alter the appliance in any way.
Do not insert anything into gaps or holes in the base. It may cause a fire, electric
shock or failure. For technical support, contact the authorized local Customer Service
Center.
• Do not use if the plug is not fully attached to the power cord. It may cause
electric shock, fire or injury.
• Do not get the base unit wet. Be careful not to let any liquids or other
substances get into the power switch on the appliance. Do not operate the power
switch with wet hands. It may cause an electric shock or fire.
• The power cord must be plugged into a grounded outlet. Do not ground it
on a gas pipe, plastic water pipe, telephone wire, etc. It could cause electric shock,
fire, malfunction, or explosion.
• Never disassemble the juicer during operation. Never insert fingers or foreign
objects such as forks, spoons, or chopsticks into the feeding tube, pulp outlet, or juice
outlet while the juicer is operating. It may cause injury, accident, or failure.
• Do not let children operate this juicer. Appliances can be used by persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge
only if they have been given supervision or instruction concerning use of the
appliance in a safe way and if they understand the hazards involved.
• Do not operate unless the hopper is properly locked in place. Failure to do
so may cause an injury or damage the appliance.
• If a gas leak is detected, do not plug in the appliance. Open a window to
ventilate fully and immediately. Failure to do so may cause injury or appliance failure.

03
Safety precautions
• If the auger stops rotating while juicing, press [REV] button and hold
for 2-3 seconds. Release the button and wait for the auger to completely stop,
then press the [ON] button again. If the juicer is overloaded and continues to stop,
the parts may become damaged and performance may be reduced due to
overheating of the motor. If the problem continues, immediately stop the appliance
and contact the local Customer Service Center.
• Do not attempt to move or disassemble the juicer while it is operating.
It can cause an injury or appliance failure. Switch off and unplug the juicer before
performing these actions.
• When using the appliance, be careful that any neckties, long
necklaces, scarves, etc. do not get caught in the juicer. It can cause injury,
appliance failure or damage.
• Only operate the appliance on a flat and stable surface.
• Do not operate the appliance for more than 30 minutes at a time. Let it
cool down for 5 minutes after every 30 minutes of use. Failure to do so may cause
damage to the motor.
• When placing ingredients into the feeding tube, only use the pusher
provided. Using any other objects can severely damage the juicer or cause
personal injury.
• Do not drop or strike the appliance with heavy objects. It may cause
electric shock, fire or damage.
• If the appliance gives off an unpleasant smell, emits smoke, or
overheats, stop using immediately and contact the local Customer
Service Center. It is natural for any new appliance to have a smell at first, but this
will disappear naturally over time.
• Always unplug the appliance after use, before disassembling or
cleaning. When unplugging the power cord, make sure to hold the power plug.
Pulling on the cord to unplug may cause electric shock or fire.
• Do not wash at high temperatures of 80C (176F) or higher. Do not put
any juicer parts in a dishwasher. It may cause failure or parts to become deformed.
• When moving the appliance, make sure to grip it by the bottom of the
base using both hands. Do not move it by holding the hopper. Failure to do so
could cause the juicer to fall resulting in damage or injury.
• Do not use this appliance for commercial purposes. Forcing an excessive
quantity of ingredients into the hopper may damage the juicer.

04
05 Pusher
03 Auger
09 Juice Container Cover 10 Juice Container
11 Pulp Container
Screw axis
02 Rotating brush
Silicon brushes
Side
hopper
Brush holder
06-08
Strainers
04 Juicing Chamber
Juice outlet
Mid gear
Pulp outlet
Lever
Juice cap
Juice cap
seal
01 Hopper
Feeding tube
Safety sensors
Ice cream
outlet
06 Fine Strainer
0
7 Coarse Strainer
0
8
Ice
C
r
eam Strainer
Strainer
bump
Pa
rts and accessories
chute

05
13 Cleaning Brush
Operating switch
Motor
axle
Safety Sensor
12 Base
Body
bumps
Pa
rts and Accessories

06
Please clean all parts before first use.
Turn the hopper counterclockwise and pull it up.
Disassemble by lifting the strainer and rotating
brush from the chamber.
Disassemble the rotating brush and strainer.
Pull out the auger
holding it by both sides.
How to disassemble the juicing chamber

07
The ice cream strainer is used for making ice cream and sorbet from frozen fruit.
It is most effective when using small amounts of diced frozen fruit. Do not overload it
with large frozen pieces. Note that some juice may leak out the output spout if using
fruit that is too defrosted. It is natural phenomenon and not a product failure. Do not
use ice cubes in the ice cream strainer.
Juice produce like pear, kiwi, cucumbers, etc. with the seeds and skin. However, apple
seeds can be toxic in large amounts, so it is better to remove them.
Separate eac
h grape from the cluster. Peel the pomegranate and use the fleshy
seeds only.
Remove the peels or rinds of watermelon, melon, orange, grapefruit, lemon and cut
them to fit in the hopper.
Fruits like mango, cherry, peach, lemon and plum have hard seeds/pits which are
difficult to swallow. Those seeds can damage the auger, so they must be removed
before using.
Cut fibrous ingredients into small sizes (max. 4 cm.) Put a handful of wheatgrass or
chives in at a time. Feed fibrous ingredients slowly.
Wash, peel, and freeze fruit before using. Cut frozen fruit into 2cm cubes. Make sure to
remove any pits or fruit stones before freezing. Please use seedless grapes. Excellent
results can be obtained from a 50/50 mixture of frozen bananas and berries.
When extracting juice from fibrous ingredients, including ginger, slice thinly and
insert slowly. When extracting juice from root vegetables such as carrots and
beets, non-food materials such as dirt on the surface may damage the parts.
Scrub or peel these before juicing. When extracting a large amount of juice,
disassemble and clean the juicer after every kilo of produce juiced.
Strainer types
► This is a general reference about how to prepare ingredients,
so if you have an allergy please choose ingredients to which you are not allergic.
► Please refer to the recipe book for more instructions regarding specific fruits.
The fine strainer has tiny holes and makes very clear juice.
Apple · Pear · Kiwi ·
Cucumber
Watermelon ·
Melon · Orange ·
Grapefruit · Lemon
Mango · Cherry ·
Peach · Lemon
Wheatgrass ·
Water Parsley ·
Choves · Celery
· Kale
Fine
Strainer
Coarse
Strainer
Ice Cream
Strainer
Fruit
Ginger · Carrots
Pomegranate ·
Grapes
H
ow to prepare ingredients for juicing
How to prepare ingredients for making ice cream/sorbet
This ice cream strainer is only for frozen fruits.
Do not use for crushing ice or grinding nuts.
Note
The coarse strainer has larger holes and makes thicker, pulpier juice. It is best
for juicing softer fruits like berries.
How to prepare produce / Strainer types

08
2
STEP
Assemble the strainer and rotating brush
as shown in the picture.
Insert the auger into the strainer.
1
STEP
How to assemble for juicing

09
After putting the hopper on the chamber,
turn it clockwise until it is locked com
-
pletely.
The juicer can be oper
ated
with the hopper assembled
in either direction.
Place the assemble
d parts from [STEP 2]
into the chamber by turning the strainer
from side to side to fit the groove in the
bottom bump of the chamber.
3
STEP
4
STEP
How to assemble for juicing
Note

10
Note
The rotating brush
isn't needed for
making ice cream .
2
STE
P
Insert the ice cream strainer into the
chamb
er. Align the ice cream outlet
with the juice chamber outlet.
Insert the auger into the ice cream
strainer and turn it from side to side
until it fits in.
1
STE
P
H
ow to assemble for maki
ng ice cream
Ju
ice outlet
Ice Cream
Outlet

11
Note
After putting the hopper on the chamber,
turn it clockwise until it is locked
completely.
3
STE
P
How to assemble for making ice cream
The juicer can be operated
with the hopper assembled in
either direction.

12
Set the control lever of the juicing
chamber to [
CLOSE
] as indicated by 1
Attach the bottom of the chamber to the tabs on
t
he base.
If the control lever is not set to
[
CLOSE
] the
juicing chamber will not attach properly.
Check that the mark on the hopper lines up with
the mark on the base unit.
How to attach the juicing chamber to the body
The assembling method is same with all three strainers.
Note
The Sana 828 is equipped with safety sensors. If
the juicing chamber is not properly assembled, the
juicer will not operate to prevent damage.
Note
The hopper contains two magnetic sensors,
allowing it to be installed in both left and right-
facing positions.

13
정회전
작동스위치
정회전
역회전
off(정지)
정지
ON
REV
[ON]
On
[REV]
Reverse
Stop
작동스위치
정회전
역회전
ON
REV
[ON]
On
[REV]
Reverse
Pusher
Upper
hopper
chute
Side
hopper
chute
Press
1
3
5
2
4
How
to use : For juicing / ice cream
Note
Make sure that the auger stops completely
before switching motor direction.
Set the lever to the [CLOSE] position
before operating.
The juicing chamber will not attach properly if
the control lever is not in the [CLOSE] position.
Press [ON] button to start.
The juicer will not turn on if the juicing chamber isn't
properly assembled and attached to the base.
Put ingredients gradually in the hopper
chute and press with the pusher.
Use only the pusher to help stuck ingredients. Do
not insert anything else into the juicer.
Cut ingredients to 3-4 cm width. When juicing
larger quantities, open the control lever every 400
ml of juice to expel excess pulp.
Juice : Put the lever in the half-closed (◑)
position before inserting the last
ingredients.
Ice Cream : Close [CLOSE] the control
lever to homogenize ice cream
ingredients.
After juicing is completed, tap the [REV]
button to stop the juicer.
Holding down the [REV] button will reverse the
motor and is used to clear jammed ingredients.

14
After detaching the juicing chamber for cleaning, set the lever
to the [OPEN ◯] position. This lets water flow more easily
when cleaning the pulp outlet. Make sure to set the level back
to the Close position after cleaning.
Note: The lever can only be set to the open position when the
juicing chamber is not attached to the body.
[ OPEN ◯ ] Cleaning Mode
Close [CLOSE] the control lever when making ice cream or
sorbet since no pulp is extracted.
[ CLOSE ] Ice Cream Mode
[ CLOSE ] Preparation·Juicing
For general ingredients, the extraction rate is best when you
close [CLOSE] the lever during operation.
When you extract over 400ml at once, please open the control
lever every 400ml to release excess pulp.
For juicing the fruits with hard seeds, such as grapes and
pomegranates, place the control lever to the close [CLOSE]
and switch into half-closed (◑) position when juice begins to
come out.
P
lace the control lever into half-closed (◑) position when putting
in the final ingr
edients. This will allow the hopper to open more
easily when you are finished juicing.
When performing the simple cleaning mode, put the
lever in half-
closed (
◑
) position
to release
th
e
pulp.
How to use control leve
r by mode
The control lever is located between the juice cap and pulp outlet.
The control lever regulates the back-pressure of pulp and can improve juice yield
Note: Stuck hopper
If it is difficult to open the hopper after juicing, put the lever in half-closed (◑) position and press [REV]
button for 3-4 seconds. Repeat this 2-3 times and the hopper will easily open.
[ ◑ ] Completion, simple cleaning mode.

15
Use the control lever according to the characteristics of each ingredient to make a
more delicious juice. When you extract over 400ml at once, please open
the control lever every 400ml to release the pulp. The hopper can’t be opened
during juicing or it may cause damage when the pressure in the chamber increases.
Apple, Pear, Melon, Watermelon, Strawberry, Blueberry, Orange, Grapefruit, Lemon, Mango, Plum, Peach,
Cherry, Persimmon, Pineapple, Wheat-Grass, Parsley, Celery, Dandelion, Carrot, Ginger, Potato, Beet,
Tomato, Pepper, Broccoli, Cauliflower, Cabbage, Kale, Spinach, Sweet Potato, Pumpkin, Corn
Grapes, pomegranate, kiwi, tomato, blackberry, raspberry, etc.
Banana, strawberry, blueberry, etc.
Put the control lever in the [ CLOSE ] position.
Put the control lever in the [ CLOSE ] position.
When extraction is almost finished, place the
control lever into the half-open [◑] position.
When juice starts to come out, place the control
lever to the [◑] half-open position.
1. Set the control lever to the [ CLOSE]
position.
Ingredients
Ingredients with seeds
Mixing with milk
How to use control lever according to ingredients (juicing)
Note

16
Cleaning the parts
When you clean the juicing chamber, wash the
inside and bottom of the chamber under running water to
remove all pulp residue.
The chamber gasket can't be removed. Do not
attempt to remove it. Trying
to remove the juicing
chamber gasket may damage it and cause leaks.
How to clean
Unplug the power cord with dry hands after the unit
has completely stopped.
Remove the juicing chamber from the main body.
Twist the chamber cover to open and lift up the
parts in order to disassemble the unit.
Using the cleaning brush, wash the parts
under
running water.
Open the control lever [OPEN ◯] and juice cap to
wash the chamber.
Wipe the main body with a damp towel or a soft
cloth.
The silicon rotating brush blades and juice cap seal
can be removed and cleaned individually.
You can sterilize the parts by soaking them for 30
minutes in a solution of water mixed with baking
soda, citric acid, or vinegar.
01
02
03
04
05
06
07
If the unit is not cleaned immediately after use, a residue may form and stick to the unit. This
will make disassembling and
cleaning difficult as well as lead to performance degradation.
Do not wash any parts with hot or boiling water, an abrasive pad or sponge, sink solvents, or
sharp cleaning tools. Do not wash any parts in a dishwasher. After washing, hand dry it with
a towel and allow it to air dry.
Note
Chamber
gasket

17
Silicone brush
1
2
3
Open the juice cap, hold the juicing chamber and juice
cap with one hand, and remove the juice cap gasket
with your other hand. Wash with warm soapy water.
Please be careful not to drop or damage the juice
cap
and juicing chamber when disassembling the unit.
Push the mid gear from the bottom side of the
juicing chamber to remove it.
Slide it back in from the top after washing it.
Juice cap gasket
Mid gear
How to clean
Remove the silicone brush from the rotating brush holder.
Hold the rotating brush holder with one hand, then slowly
pull off the brush blade. Begin at the top of the blade and
pull outward and down.
Use the cleaning brush and wash the inside and outside of
the rotating brush holder under running water.
Wash the silicone brush blade under running water. Use
the brush to dislodge any particles in the groove of the
blade.
After cleaning, attach the silicone brush by pushing on the
back of the brush holder ❶ while pulling the inner wing
inward with your other hand as shown in the picture. Pull until
it cannot be pulled any further. ❷ Grab the top and bottom of
the outer wing and pull them tight.
If the silicone brush blades aren't properly assembled, they could
come off during juicing or will clean less effectively.
❶
❷

18
Ingredients which require special attention
- Fruits with hard seeds or pits such as persimmon, Japanese apricot, lemon, plum, peach etc.
that are hard to chew with our teeth must have their pits removed before juicing.
- Stalk vegetables with strong fibers such as water parsley and celery should be cut into small lengths
about 3-4 cm before juicing.
- Do not put in dry ingredients such as sesame, coffee beans, nuts, etc. which cannot be juiced.
- Do not put in canned or jarred fruits preserved in alcohol, water, honey, etc. (cherries, apricots, berries, etc.)
- Do not juice ingredients with very low moisture content such as figs, aloe and cactus. (Please contact the
Customer Service Center for more information on which ingredients can be juiced.)
- Extracting the juice from more than 1 kg of root vegetables at a time, including ginger,
may cause damage or failure. Please repeat the process of "juicing 1 kg, disassembling, and cleaning".
We recommend you to drink fresh juices immediately after extraction for the highest nutrition
Do not use juicer for grinding grain.
- It may cause damage or appliance failure.
Do not juice pulp a second time.
- Soft fruits can be re-squeezed.
Do not put produce in the juicer before turning it on
Do not use the juicer for more than 30 minutes continuously.
- It may cause motor failure due to overheating .
- When using continuously, give it a 5-minute break every 30 minutes.
Never insert anything (including knives, forks, or chopsticks) into the pulp outlet during operation
- Foreign objects can get caught by the rotating brush and can damage the juicing screen
Never insert anything (including knives, forks, or chopsticks) into the feeding tube during operation
- It may get caught by the auger and break the juicing chamber.
Do not operate the switch with wet hands.
- It may cause electric shock or fire.
When juicing large quantities of fruits and vegetables,
please open the control lever every 400ml to eject the pulp.
- Otherwise pulp can build up, making it difficult to open the chamber after juicing
Please only use frozen fruit with the ice cream strainer
Do not use the ice cream strainer for grinding nuts or herbs
- It may cause damage or failure.
Precautions while juicing
N
ote
Older or wilted produce will make less or no juice. Always use fresh ingredients. If the unit is not
cleaned immediately after use, a residue may dry and stick
to the unit. This will make assembling
and cleaning difficult as well as lead to performance degradation.

19
[ON]
On
[REV]
Reverse
[REV]
OFF
[ON]
On
When you switch the juicer to [REV], the auger does not stop immediately. Do
not switch the juicer to operate in the opposite direction until the auger’s
movement has completely stopped. Once the rotation stops completely, you
may switch to operate in either direction.
►The juicer may stop if ingredients are overloaded or inserted too quickly.
►Gradually insert ingredients, since the juicer squeezes them instead of grinding.
N
ote
[REV]
Reverse
If the auger stops during juicing
Caution when using operating switch
Press [REV] for 3 - 5 seconds to release pressure
from the auger. Repeat if n
ecessary.
Reverse is a function that rotates (or operates) the
auger (motor) in the opposite direction.
Reverse rotation operates only while holding the
switch in [REV] position, and shuts off when the
switch is released.
Press [ON] after the auger stops completely to
continue juicing.
Before
reversing directions, make sure that
the auger stops completely.
1
2
Note
If the auger still won’t turn after following the above
directions, unplug the power cord, disassemble
the juicer, clean the
parts, and try again.

20
Make sure that the power cord is properly plugged in. Check that the hopper is assembled properly.
The appliance may not operate when used for more than 30 minutes. In this case, let the machine cool
off at least 5 minutes. If the hopper has not been properly locked into place, the appliance will not
operate for safety reasons.
Check if the appliance is assembled according to the directions in the manual.
Refer to instructions for assembly in the manual or consult with your Customer Service Center for
additional assistance.
04 The appliance stops during normal operation.
Is the juicer overloaded, especially with solid ingredients like beets or carrots?
Refer to page 19 of the manual and follow the guidelines for using [REV] button. If the issue is not
resolved after following the above process, please contact your local Customer Service Center.
05 There are fine lines or scratch marks on the auger.
These are molding marks resulting from the normal manufacturing process. This is normal and does
not affect the operation of the juicer.
06 Chamber set does not fit into the base.
If the lever is in OPEN ◯ position, the juicing chamber set will not fit in the base.
Before assembling, set the lever to the CLOSE position.
01 The main body will not work by itself.
For your safety, this unit only works when
main body is correctly assembled with the
juicing chamber set.
03 The juicer does not work.
02 Please make sure the line on the
h
opper is properly aligned with the body
For your safety, this juicer will only operate
when the hopper is properly aligned. Note that it
can be aligned in two directions.
Before requesting a repair

21
Have you forced a lot of ingredients into the feeding tube?
If you force too many ingredients at once into the feeding tube, especially ingredients with a
high pulp content, the gasket can be pushed back by the force, allowing a small amount of juice
to escape. Allow most ingredients to self-feed, and make sure pulpy ingredients are cut to the
proper size. Do not try to over-feed the juicer by force. Please contact the Customer Service
Center if juice continues to leak from above the body.
10 The hopper does not open.
There might be a lot of pulp inside the juicing chamber. Set the lever to the half-closed position,
and press the [ON] button to release excess pulp.
Press [REV] button for 3-5 seconds and then release the button. Repeat this process 2-3 times.
Have you placed any foreign substances or solid objects (hard seeds such as persimmon)
in the juicer?
Press [REV] button to push the ingredients back up toward the feeding tube. This should reduce
the pressure on the lid and allow the hopper to open. Do not attempt to open by force.
Please contact your local Customer Service Center for assistance if it still will not open.
11 The Chamber shakes when juicing.
Slight shaking may be caused by the motor.
Depending on the texture of the ingredients, there may be slight to more pronounced shaking
of the juicing chamber while juicing. This is normal and is a result of the auger rotating. Hard
ingredients such as carrots, radishes, and beets may cause more shaking than soft ingredients.
08 Only use the pusher when feeding
ingredients. Other objects will damage
the juicer.
Note: Most ingredients will self-feed. Only use the
pusher if an ingredient becomes stuck.
07 Do not insert too many ingredients
at once.
If you insert an excessive amount of ingredients
or improperly cut ingredients, the unit may stop.
09 Juice leaks over the base.
Before requesting a repair
When calling for service, please have the
manufacturer’s serial number or bar code available.

22
Product Specifications / Warranty
Product Name
Model Name
Rated Voltage
Rated Frequency
RPM
Sana Slow Juicer
EUJ-828
230-240 V
50 Hz
150 W
43 rpm
Cord Length
Motor
Fuse
Weight
Rated Operating Time
1.4 m
250 V 5 A
6.5 kg
30 minutes
Width 252 mm
Length 211 mm
Height 430 mm
Single-phase induction motor
Product Specifications
External
Dimensions
Rated Power Consumption

www.sanaproducts.eu
The future of your healthy kitchen.
Produkt Specifikationer
Mærke: | Sana |
Kategori: | Juicer |
Model: | EUJ-828 |
Tænd-/slukkontakt: | Ja |
Vekselstrømsindgangsspænding: | 230-240 V |
Vekselstrømsindgangsfrekvens: | 50 Hz |
Bredde: | 252 mm |
Dybde: | 211 mm |
Højde: | 430 mm |
Vægt: | 6500 g |
Brugervejledning: | Ja |
Produktfarve: | Rød |
Kontroltype: | Knapper |
Produkttype: | Slow juicer |
Strøm: | 150 W |
Ledningslængde: | 1.4 m |
Rotationshastighed: | 43 rpm |
Rengøringsbørste: | Ja |
Pulpbeholder: | Ja |
Saftbeholder: | Ingen |
Kande: | Ja |
Sikring: | 5 A |
Skruetype: | Vertikal snegl |
Kontinuerlig driftstid (maks.): | 30 min. |
Har du brug for hjælp?
Hvis du har brug for hjælp til Sana EUJ-828 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Juicer Sana Manualer
1 September 2024
21 August 2024
20 August 2024
20 August 2024
18 August 2024
17 August 2024
17 August 2024
17 August 2024
16 August 2024
Juicer Manualer
- Livoo
- PowerXL
- Solis
- Roadstar
- Exido
- Orbegozo
- Palson
- WMF
- Waring Commercial
- Kambrook
- Kuvings
- Trisa
- Inventum
- Suntec
- Emerio
Nyeste Juicer Manualer
3 April 2025
27 Februar 2025
25 Februar 2025
24 Februar 2025
11 Februar 2025
13 Januar 2025
13 Januar 2025
11 Januar 2025
10 Januar 2025
4 Januar 2025