Sani-Lav 512FSL Manual


Læs gratis den danske manual til Sani-Lav 512FSL (7 sider) i kategorien Køkkenvask. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Sani-Lav 512FSL, eller vil du spørge andre brugere om produktet?

Side 1/7
1
H A N D S - F R E E F L O O R M O U N T W A S H S TAT I O N
Columbia does not recommend use with harsh chemicals.
Product Compliance
NSF/ANSI 2 Food Equipment, NSF/ANSI 372 Low-Lead
Operating Manual for 6-Person Hands-Free Floor Mount
Stainless Steel Wash Station
Models 512FSL 512FSL-0.5 and
of Domestic and Foreign Parts
2
H A N D S - F R E E F L O O R M O U N T W A S H S TAT I O N
800.626.2117 columbiasinks.com info@columbiasinks.com
©2021 Columbia Products
Parts List
(1) Floor mount wash station
(1) Leg assembly set
(18) Nuts, bolts and washers for leg assembly
(8) Washers and nuts for connection sink to leg assembly set
(6) Double foot pedal valve
(12) Valve mounting nuts
(6) Swivel gooseneck spout with aerator
(6) Connecting tube for valve to spout connection
(12) Fittings, brass, 0.375” male compression and 0.375” male NPT
(3) Strainer assembly with basket
Installation Instructions
Step 1
1. 2 and 3-Person models require leg assembly.
2. Place wash station sink on leg assembly and secure with hardware (provided).
3. Establish sink location.
4. Mark the floor where the four holes are at the base as shown in illustration A.
5. Drill holes as required for mounting hardware. (Hardware not included).
Step 2
1. Install spout assembly to the sink.
2. Install elbow fitting (provided) to the spout assembly.
3. Connect one side of the supply line (provided) to the spout assembly.
4. Install strainer assembly.
Step 3
1. Install elbow fitting to valve.
2. Install foot pedal valves under the leg assembly cross bar if not mounted already.
3. Attach connecting tube from the spout to the foot pedal valve.
Step 4
1. Secure wash station to the floor.
2. Connect waste line to strainer assembly.
3. Connect water supplies (hot and cold) to valves.
Step 5
1. Remove aerator from the spout assembly and flush water line by pressing pedal for
30 seconds.
2. Check connections for leaks. Replace aerator onto the spout assembly.
3. Seal gap between bowl and leg assembly as shown in illustration B.
4. When mounting against wall, we recommend sealing top of backsplash to wall as shown
in illustration C.
Tools Required
Tape measure
Adjustable wrench
Drill motor and drill bits
Pipe wrench
Level
Safety glasses
Screw drivers: phillips and standard
Pencil
Socket wrench
Go to for more information on replacement parts and installation videos.columbiasinks.com
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certied under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Illustration A
Illustration B
Illustration C


Produkt Specifikationer

Mærke: Sani-Lav
Kategori: Køkkenvask
Model: 512FSL

Har du brug for hjælp?

Hvis du har brug for hjælp til Sani-Lav 512FSL stil et spørgsmål nedenfor, og andre brugere vil svare dig




Køkkenvask Sani-Lav Manualer

Køkkenvask Manualer

Nyeste Køkkenvask Manualer