Sanus VMCA1 Manual


Læs gratis den danske manual til Sanus VMCA1 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Sanus VMCA1, eller vil du spørge andre brugere om produktet?

Side 1/1
Assembly Instructions for Model: VMCA1b-01
Thank you for choosing a Sanus Systems VisionMount accessory. The Ceiling Plate is designed for ease of installation
with any height of drop ceiling. By using any length of standard NPT pipe threaded both ends, you can extend the height
capabilities to meet your needs.
WARNING: If you do not understand these directions, or have any doubts about the safety of the installation, please
contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective
parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged
parts. Replacement parts for products purchased through authorized dealers will be shipped directly to you. Never use
defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that
is not explicitly specied by Sanus Systems. Sanus Systems can not be liable for damage or injury caused by incorrect
assembly, or incorrect use. Please contact Sanus Systems before returning products to the point of purchase.
WARNING: Improper installation may result in serious personal injury. When mounting Sanus accessories, the
structural system and mounting method must be capable of supporting ve (5) times the combined weight of the
total installation. The maximum weight to be installed on the Ceiling Plate is 500 lbs. [226.8 Kg].
Parts List:
(1) 4 Flat Ceiling Plate CMA-101 (1) 5/16-18 x 3/8 Security Set Screw Socket Set Screw,
1. Securely install the ceiling plate to the ceiling joist. Bolt hole spacing is shown in Diagram 1. If using only two holes for
mounting, you must use opposing holes.
2. Thread your NPT1-1/2 pipe into the coupler; then, tighten securely.
3. Install and securely tighten the 5/16-18 x 3/8 Socket Set Screw or, if desired, the Security Set Screw.
4. Follow the Ceiling Mount Instruction mating components or mounts.
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 (6901-100144<00>)
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Diagram 1
2.00”
4.00”
5.00”
2.00”
4.00”
5.00”
0.69”
1-1/2” NPS
Opposing Holes


Produkt Specifikationer

Mærke: Sanus
Kategori: Ikke kategoriseret
Model: VMCA1

Har du brug for hjælp?

Hvis du har brug for hjælp til Sanus VMCA1 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Sanus Manualer

Sanus

Sanus VXL7 Manual

9 December 2025
Sanus

Sanus LF228 Manual

17 November 2025
Sanus

Sanus CFR1610 Manual

27 September 2025
Sanus

Sanus BMF220 Manual

27 September 2025
Sanus

Sanus VisionMount LMT15 Manual

27 September 2025
Sanus

Sanus BSA-OWCM332 Manual

27 September 2025
Sanus

Sanus VMD2 Manual

27 September 2025
Sanus

Sanus NF213 Manual

26 September 2025
Sanus

Sanus VisionMount VLT14 Manual

26 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone

Waterstone 7800 Manual

11 December 2025
Kwikset

Kwikset 258 Manual

11 December 2025
Schlage

Schlage F170 Manual

11 December 2025
Moen

Moen Align 7565EV Manual

11 December 2025
ALNO

ALNO MC10244 Manual

11 December 2025
JET

JET TAK-ZX Manual

11 December 2025
Waterstone

Waterstone 1455 Manual

11 December 2025
Laica

Laica NE2015 Manual

11 December 2025