Satco S11757 Manual

Satco Skærm S11757

Læs gratis den danske manual til Satco S11757 (6 sider) i kategorien Skærm. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Satco S11757, eller vil du spørge andre brugere om produktet?

Side 1/6
1
LED T8 REPLACEMENT LAMPS
Models: S11757
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing xture. Retain for future reference.
Item Number-Description
Minimum Lamp
Compartment Dimensions
(Length x Width x Height) (cm)
Lamp
Quantity
Lamp-to-Lamp
Spacing (cm)
S11757-40T8/LED/96-CCT/BP/R2PC/1PK 244 x 27 x 7 2 11
WARNING:
DANGER: Risk of shock-disconnect power before
installation.
WARNING: Risk of re or electric shock. LED
Retrot Kit installation requires knowledge of luminaire
electrical systems. If not qualied, do not attempt
installation. Contact a qualied electrician.
WARNING: Product must be installed in accordance
with the national electrical code or your local electrical
code. If you are not familiar with these codes and
requirements, contact a qualied electrician.
WARNING: Install this kit only in luminaries that have
the construction features and dimensions shown in the
photographs and/or drawing and where the input rating
of the retrot kit does not exceed the input rating of
the luminaire.
WARNING: To prevent wiring damage or abrasion,
do not expose wiring to edges of sheet metal or other
sharp objects.
Do not make or alter any open holes in an enclosure of
wiring or electrical components during kit installation.
Installers should not disconnect the existing wire from
lampholder terminals to make new connections at
lampholder terminals. Instead installers should cut
existing lampholder leads away from the lampholder
and make new electrical connections to lampholder
lead wires by employing applicable connectors.
WARNING: Luminaire wiring and electrical parts
may be damages when installing retrot kit hardware.
Check for enclosed wiring and components.
WARNING: Risk of re or electric shock.
Installation of this retrot assembly requires a person
familiar with the construction and operation of the
luminaires electrical system and the hazard involved.
If not qualied, do not attempt installation. Contact a
qualied electrician.
CAUTION: Risk of electric shock. Do not use if
outer lamp envelope is damaged or broken.
Installers should examine all parts that are not intended
to be replaced by the retrofit kit for damage and replace
any damaged parts prior to installation of the retrofit kit.
WARNING: Check the existing wiring for damage
before installing upgrade kit. Do not install if existing
wires are damaged.
The retrot kit is accepted as a component of a
luminaire where the suitability of the combination
shall be determined by authorities having jurisdiction.
Product must be installed by a qualied electrician
in accordance with the applicable and appropriate
electrical codes. The installation guide does not
supersede local or national regulations for electrical
installations.
Type B Lamp – intended for operation in luminaires
with traditional uorescent-type lamp holders wired
directly to the branch circuit. This includes both
factory-wired luminaries as well as those converted
for this purpose under a retrot program.
THIS RETROFIT KIT INCLUDES, LED TUBE,
OPERATING INSTRUCTIONS, AND FIXTURE LABEL
FOR THE DOUBLE OR SINGLE ENDED APPLICATION.
“This luminaire has been modied and can no longer
operate the originally intended lamp,” shall be marked
on the retrot luminaire where readily visible by the user
during normal maintenance including lamping.
Only use the control provided with or specied by
these instructions to control this lamp. This lamp will
not operate properly when connected to a standard
(incandescent) dimmer or dimming control. For dimming,
only operate at 120-277V with specic dimmer, Dim-mate
accessory, manufactured by Jiaxing Super Lighting.
Suitable for damp locations.
Suitable for use in enclosed luminaries.
Suitable for use with the following emergency
equipment; SATCO Products, Inc., Model S8002,
10W Emergency LED Driver.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation.
The units covered by this report were intended to retrot surface mount, Type IC or non-IC recessed mount Listed uorescent
luminaires that use maximum 2 tubular lamps, the minimum lamp compartment dimensions are tabulated below.
Features, applications and installation instructions
continued on pages 2-4.
Satco Products, Inc.
Brentwood, NY 11717© Copyright 2024 Satco Products, Inc. 8/24 v3.0


Produkt Specifikationer

Mærke: Satco
Kategori: Skærm
Model: S11757

Har du brug for hjælp?

Hvis du har brug for hjælp til Satco S11757 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Skærm Satco Manualer

Satco

Satco S11757 Manual

16 December 2025
Satco

Satco S11965 Manual

16 December 2025
Satco

Satco S11985 Manual

15 December 2025
Satco

Satco S23113 Manual

15 December 2025
Satco

Satco S11999 Manual

11 December 2025
Satco

Satco S11741 Manual

11 December 2025
Satco

Satco S23114 Manual

11 December 2025
Satco

Satco S11980 Manual

11 December 2025
Satco

Satco S23150 Manual

11 December 2025
Satco

Satco S11987 Manual

11 December 2025

Skærm Manualer

Nyeste Skærm Manualer

Aqprox

Aqprox appMT17W5 Manual

16 December 2025
Advantech

Advantech FPM-7151T Manual

16 December 2025
AOC

AOC Q27G4SDR Manual

10 December 2025
Dell

Dell S2725HSM Manual

10 December 2025
Dell

Dell S2425HSM Manual

10 December 2025