Savage Promo Background Stand Manual

Savage Ikke kategoriseret Promo Background Stand

Læs gratis den danske manual til Savage Promo Background Stand (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Savage Promo Background Stand, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
CONTENTS
(2) T-Legs
(2) Telescoping uprights
(4) Crossbar sections
(2) Crossbar connectors
(2) Allen head screws
(1) Allen wrench
(1) Carry bag
Unscrew the knurled knob on the end of
each crossbar section until the screw is
completely unthreaded.
Slide the threaded knob through
the hole nearest the top of the upright.
Thread one side of the crossbar into the
threaded knob until tight.
REPEAT ON SECOND UPRIGHT ON OPPOSITE SIDE
1) ASSEMBLING T-LEG BASE
Slide telescoping upright stand section through the hole located
on top of the T Leg. Use the included allen wrench to tighten the
upright using the included Allen head screw.
REPEAT TO ATTACH SECOND UPRIGHT TO THE SECOND T LEG
2) ASSEMBLING UPRIGHTS
Extend the upright section nearest the
top 6" and tighten for both uprights.
3) ASSEMBLING CROSSBARS
Connect the 2 sections of both crossbar sets
using the silver crossbar connectors,
making sure that the pin on the
connector is lined up with the
hole on each crossbar
section.
Push together until the silver pin
snaps into the hole on the
crossbar.
5) RAISING UPRIGHTS
Raiser the lowest section of the up
right stand on both sides and
re-tighten.
RAISE UPRIGHT LOWER SECTIONS 6” THE CROSSBAR WILL NOT ATTACH THROUGH THE
DRILLED HOLES IF THE UPRIGHT IS ALL THE WAY DOWN
Assembly & Usage
Instructions
PROMO
BACKGROUND STAND
WWW.SAVAGEUNIVERSAL.COM
6) ATTACHING LOWER CROSSBAR TO UPRIGHT
Repeat Step 4 to connect the second
crossbar to the upright stands using the
drilled holes located at the bottom of
the lowest upright stand section.
Be sure to raise the lowest
section of the upright
6" before attempting
to connect the
crossbar.
USE OF SAVAGE PROMO STAND
Telescoping crossbars can be adjusted to accommodate backdrops or banners
as small as 6’ wide up to 9’ 8” wide. Telescoping upright stands can be adjusted
from 40” tall up to 8’ tall. Detach one side of top crossbar from the upright stand
to slide on backdrops that have a sewn-in pole pocket or simply secure the
material to the crossbar using standard clamps. To pull out wrinkles from the
backdrop or banner, clamp the bottom edge of the material to the bottom
crossbar with clamps. This support stand is an especially ideal system for cloth
backgrounds.

Produkt Specifikationer

Mærke: Savage
Kategori: Ikke kategoriseret
Model: Promo Background Stand

Har du brug for hjælp?

Hvis du har brug for hjælp til Savage Promo Background Stand stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Savage Manualer

Savage

Savage Promo Background Stand Manual

3 December 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Blumfeldt

Blumfeldt Ebeko Manual

3 December 2025
Steiner

Steiner OTAL-A Manual

3 December 2025
Vevor

Vevor YCS-9038-16 Manual

3 December 2025
ELO

ELO E176840 Manual

3 December 2025
Lava

Lava Probuds T12 Manual

3 December 2025
Lutec

Lutec Telis Manual

3 December 2025
SPT

SPT SET-2033 Manual

3 December 2025
Vevor

Vevor WS-SS2-01 Manual

3 December 2025
Urbanista

Urbanista Buenos Aires Manual

3 December 2025
FLIR

FLIR Scout BTS-X Pro Manual

3 December 2025