Schneider MTN629993 Manual

Schneider Ikke kategoriseret MTN629993

Læs gratis den danske manual til Schneider MTN629993 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Schneider MTN629993, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

DANGER

Risk of fatal injury from electrical current.

All work on the device should only be carried out

by trained and skilled electricians. Observe the

country-specific regulations as well as the valid

KNX guidelines.

½CAUTION

The device could be damaged.

Only operate the device according to the

specifications stated in the Technical data.

The switch actuator UP/230/16 (referred to below as the

actuator) can switch one load via a floating make

contact.

Mount the actuator in a wall or ceiling socket-outlet with

a diameter of 60 mm and a depth of at least 40 mm. For

ceiling mounting, the hook on which the luminaire is

suspended can be screwed onto the ceiling socket-

outlet through the centre hole in the actuator.

AConnection of electrical loads, AC 230 V

BProgramming button

CBus connecting terminal

DProgramming LED (red)

For your safety

Getting to know the switch actuator

Connections, displays and operating

elements

1Mount the actuator in a flush-mounted box at least

40 mm deep.

Use the opposite entry openings A of the installation

box for the 230 V cable and the bus line. The actuator

itself serves as a separating web.

2 BConnect KNX . The sheath of the bus line must

be cut back as short as possible at the bus

terminal.

½WARNING

Risk of fatal injury from electrical current. The

device could become damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX line.

½CAUTION

The device could be damaged.

If you are switching socket-outlets with the

actuator, it is not possible to ensure that

exclusively ohmic loads are connected. Fuse the

circuit with 10 A.

3Connect the load.

4Connect the bus voltage.

5Connect the load voltage.

1Press the programming button.

The programming LED lights up.

2Load the physical address and application into the

device from the ETS.

The programming LED goes out.

The application was loaded successfully, the device is

ready for operation.

Mounting the actuator

Putting the actuator into operation

230 V

4 mm

KNX

KNX L1 N

If you have technical questions, please contact the Cus-

tomer Care Center in your country.

www.schneider-electric.com

This product must be installed, connected and used in

compliance with prevailing standards and/or installati-

on regulations. As standards, specifications and de-

signs develop from time to time, always ask for

confirmation of the information given in this publicati-

on.

Schneider Electric Industries SAS

Technical data

Power supply from

bus:

DC 24 V/approx. 10 mA

Insulation voltage: 4 kV between bus and AC 230 V

Switch contacts: 1 x make contacts

Nominal voltage: AC 230 V, 50 to 60 Hz

Nominal current: 16 A, ohmic load cos ϕ = 1

10 A, inductive load cos ϕ = 0.6

Connected load

Incandescent

lamps: AC 230 V, max. 2700 W with

20,000 switching cycles

Halogen lamps: AC 230 V, max. 1700 W with

20,000 switching cycles

Fluorescent lamps: AC 230 V, max. 1000 VA,

parallel-compensated with

5,000 switching cycles

Capacitive load: AC 230 V, 10 A max. 105 µF

with 5,000 switching cycles

Fuse: The switch contact must be

protected by a series-connected

circuit-breaker.

Switching

frequency: max. 10 per minute at nominal

load

Ambient temperature

Operation: -5 °C to +45 °C

Storage: -25 °C to +55 °C

Transport: -25 °C to +70 °C

Environment: can be used at up to 2000 m

above sea level (MSL)

Operating element: 1 programming button

Display element: 1 red LED: programming check

Connections

Bus: via two 1 mm pins for bus

connecting terminal

Outer conductor: two screw terminals for max.

2.5 mm²

EC guidelines: Complies with Low-Voltage

guideline 73/23/EEC; complies

with EMC guideline 89/336/EEC

Dimensions: 51 x 52 x 29 mm (W x H x D)

Switch actuator, flush-mounted/230/16

Operating instructions

Art. no. MTN629993

V6299-562-00 01/08

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN629993

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN629993 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider Rhodos Twist Manual

22 November 2025

Schneider VW3A3809 Manual

21 November 2025

Schneider TeSys D LR97D015 Manual

11 November 2025

Schneider Homeline HOM2175SB Manual

9 November 2025

Schneider EVlink Wallbox EVH2S22P02K Manual

7 November 2025

Schneider XVUC29P Manual

7 November 2025

Schneider LC1F1400MD Manual

7 November 2025

Schneider TeSys GS GS1DD3 Manual

6 November 2025

Schneider EVlink Wallbox EVH2S7P02K Manual

6 November 2025

Schneider EVlink Wallbox EVH2S11P02K Manual

6 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Brondell LumaWarm L60 Manual

18 December 2025

Vaxcel T0701 Manual

18 December 2025

Bravilor Bonamat Bolero 32 CS Manual

18 December 2025

Foscam SD8EP Manual

18 December 2025

Dals DCP-LWS19 Manual

18 December 2025

Vaxcel T0249 Manual

18 December 2025

TOTO TS110J1 Manual

18 December 2025

ORNO OR-CR-298 Manual

18 December 2025

Wine-Mate WM-4500SSLWC Manual

18 December 2025

Aqprox appLS05HD2D Manual

18 December 2025