Schneider MTN644592 Manual

Schneider Ikke kategoriseret MTN644592

Læs gratis den danske manual til Schneider MTN644592 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Schneider MTN644592, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

The binary input REG-K/8x10 is used to connect eight

floating contacts, push-buttons or switches to the bus

system.

The binary input makes a contact supply voltage (SELV)

available which is electrically isolated from the bus

voltage. A power supply is thus not necessary for the

connected floating contacts.

The binary input has a bus coupler. It is installed on a

DIN rail acc. to EN 60715, with the bus connection

made via a bus connecting terminal. A data rail is not

required.

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connecting and establishing KNX networks

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• Never connect the device to an external power

source.

• The binary input circuits must comply with the safety

extra-low voltage conditions (SELV) in accordance

with IEC 60364-4-41.

• Only operate the device according to the specifica-

tions stated in the Technical data.

• All the devices that are installed next to the binary in-

put must be equipped with basic insulation at the very

least.

Failure to follow these instruction can result in

equipment damage.

Binary input introduction

ACover of the bus connecting terminal

BProgramming button/programming LED

COperational LED

DChannel status LEDs

1Set the binary input onto the DIN rail.

2Connect KNX.

WARNING

Risk of fatal injury from electrical current.

The device could be damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX line.

Operating and display elements

Installing the binary input

RUNE 8E 7E 6

E 5

E 4E 3E 2E 1

E1 0 V 0 V E2 E3 0 V 0 V E4

E5 0 V 0 V E6 E7 0 V 0 V E8

5 mm

1 2

3 4

230 V

4 mm

KNX

3Connect the input cables.

|An installation with Y bell wire or J-FY flat

webbed bell wire is permitted.

1Press the programming button.

The programming LED lights up.

2Load the physical address and the application into

the device from the ETS.

The operating LED lights up: The application was loaded

successfully, the device is ready for operation.

Schneider Electric Industries SAS

35 rue Joseph Monier

Rueil Malmaison 92500

France

If you have technical questions, please contact the Cus-

tomer Care Centre in your country.

se.com/contact

Putting the binary input into operation

Technical data

Power supply from

bus: DC 24 V / max.18 mA

Insulation voltage: AC 4 kV bus/inputs

Inputs

Contact voltage: max. 10 V (SELV)

Contact current: max. 2 mA, pulsating

Transfer resistance

(between contact and

cable):

max. 500  when contact

closed,

min. 50 k when contact

open

Permitted cable

length: max. 50 m

Ambient temperature

Operation: -5 °C to +45 °C

Storage: -25 °C to +55 °C

Transport: -25 °C to +70 °C

Max. humidity: 93 % relative humidity, no

moisture condensation

Environment: The device is designed for use

at a height of up to 2000 m

above sea level (MSL).

Connections

Inputs, outputs: Screw terminals

Single-core: 1.5 mm2 to 2.5 mm2

Finely stranded

(with core end sleeve): 1.5 mm2 to 2.5 mm2

Bus: Bus connecting terminal

Dimensions

Height x width x

depth: 90 x 72 x 65 mm

Device width: 4 modules

Schneider Electric -Contact

KNX

+ -

0 V

Schneider Electric Limited

Telford, TF3 3 BL, UK

UK Representative

Stafford Park 5

SpaceLogic KNX Binary input REG-K/8x10

Operating instructions

Art. no. MTN644592

RUNE 8E 7

E 6E 5E 4E 3E 2E 1

V6445-562-01 11/21

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN644592

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN644592 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider Rhodos Twist Manual

22 November 2025

Schneider VW3A3809 Manual

21 November 2025

Schneider TeSys D LR97D015 Manual

11 November 2025

Schneider Homeline HOM2175SB Manual

9 November 2025

Schneider EVlink Wallbox EVH2S22P02K Manual

7 November 2025

Schneider XVUC29P Manual

7 November 2025

Schneider LC1F1400MD Manual

7 November 2025

Schneider TeSys GS GS1DD3 Manual

6 November 2025

Schneider EVlink Wallbox EVH2S7P02K Manual

6 November 2025

Schneider EVlink Wallbox EVH2S11P02K Manual

6 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Brondell LumaWarm L60 Manual

18 December 2025

Vaxcel T0701 Manual

18 December 2025

Bravilor Bonamat Bolero 32 CS Manual

18 December 2025

Foscam SD8EP Manual

18 December 2025

Dals DCP-LWS19 Manual

18 December 2025

Vaxcel T0249 Manual

18 December 2025

TOTO TS110J1 Manual

18 December 2025

ORNO OR-CR-298 Manual

18 December 2025

Wine-Mate WM-4500SSLWC Manual

18 December 2025

Aqprox appLS05HD2D Manual

18 December 2025