Schneider MTN647393 Manual

Schneider Ikke kategoriseret MTN647393

Læs gratis den danske manual til Schneider MTN647393 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 65 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 33 anmeldelser. Har du et spørgsmål om Schneider MTN647393, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

V6473-561-02 11/21

SpaceLogic KNX

Switch actuator REG-K/2x230/16 with

manual mode

Operating instructions

Art. no. MTN647393

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connecting and establishing KNX networks

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

RISK OF FATAL INJURY FROM ELECTRIC SHOCK

The output may carry electrical current even when the

load is switched off.

• When working on the device: Always disconnect the

device from the supply by means of the fuse in the in-

coming circuit.

• Even if the manual switch is in the „OFF“ position, a

KNX telegram can switch the connections to being

live at any time. Before working on the device, always

diconnect the fuse in the incoming circuit from the

supply.

Failure to follow these instructions will result in

death or serious injury.

L 2L 1

The switch actuator REG-K/2x230/16 with manual mode

(referred to below as the actuator) can switch two loads

via separate, floating make contacts.

You can also manually switch the connected loads with

manual switches on the actuator without bus voltage.

The actuator has a bus coupler. It is installed on a DIN rail

TH 35 according to EN 60715, with the bus connection

made via a bus connecting terminal. It is supplied with

power from the bus voltage. A data rail is not required.

ABus connection terminal, max. 4 core pairs

BProgramming LED (red)

CProgramming button

DCable cover

EOperating LED „RUN“ (green)

FManual switch

GScrew terminals

1Set the actuator onto the DIN rail.

The device may be damaged!

• Always operate the product in compliance with the

specified technical data.

• Only install devices with at least basic insulation next

to the device.

Failure to follow these instruction can result in

equipment damage.

Getting to know the actuator

Connections, displays and operating

elements

Mounting the actuator

L L 2L L 1

KNX

1 2

2Connect KNX.

¼WARNING

Risk of death from electric shock. The device

can become damaged.

Safety clearance must be guaranteed in accord-

ance with IEC 60664--1. There must be at least 4

mm between the individual cores of the 230 V

supply cable and the KNX line A.

3Connect the bus voltage.

4Wait at least 30 seconds.

5Switch the relays of the channels on and off manu-

ally once with the manual switches.

6Connect the load.

The cables to the loads as well as the system voltages

(L1, L2 or L3) are connected via screw terminals for max.

16 A. Every two L connections are bridged internally.

7Connect the mains voltage.

Now you can check the functionality of the actuator and

the connected loads without having to load the applica-

tion from the ETS (See the section "Operating the actua-

tor").

RISK OF FATAL INJURY FROM ELECTRIC SHOCK

Voltage may be present at the outputs when the mains

voltage is connected to the system.

If subjected to strong vibrations during transportation,

the switch contacts might change to the enabled state.

After connecting the bus voltage, set the relays of the

channels to the position desired simply by switching

„On/Off“ or by changing the manual switch to „OFF“.

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• Protect the switch contacts with a series-connected

16 A circuit breaker.

Failure to follow these instruction can result in

equipment damage.

1 2

5 mm

230 V

4 mm

KNX

16 A

16 A 16 A

L2 L3 N

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN647393

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN647393 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider Rhodos Twist Manual

22 November 2025

Schneider VW3A3809 Manual

21 November 2025

Schneider TeSys D LR97D015 Manual

11 November 2025

Schneider Homeline HOM2175SB Manual

9 November 2025

Schneider EVlink Wallbox EVH2S22P02K Manual

7 November 2025

Schneider XVUC29P Manual

7 November 2025

Schneider LC1F1400MD Manual

7 November 2025

Schneider TeSys GS GS1DD3 Manual

6 November 2025

Schneider EVlink Wallbox EVH2S7P02K Manual

6 November 2025

Schneider EVlink Wallbox EVH2S11P02K Manual

6 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Brondell LumaWarm L60 Manual

18 December 2025

Vaxcel T0701 Manual

18 December 2025

Bravilor Bonamat Bolero 32 CS Manual

18 December 2025

Foscam SD8EP Manual

18 December 2025

Dals DCP-LWS19 Manual

18 December 2025

Vaxcel T0249 Manual

18 December 2025

TOTO TS110J1 Manual

18 December 2025

ORNO OR-CR-298 Manual

18 December 2025

Wine-Mate WM-4500SSLWC Manual

18 December 2025

Aqprox appLS05HD2D Manual

18 December 2025