SentrySafe T8-311 Manual

SentrySafe Vault T8-311

Læs gratis den danske manual til SentrySafe T8-311 (3 sider) i kategorien Vault. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om SentrySafe T8-311, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Thank you for purchasing

this Sentry product.

For safes with key lock only

Your Sentry safe is equipped with a high security, 8 lever key lock, two (2) keys

are provided.

For safes with electronic lock

Battery Installation

To power the lock, four alkaline AA batteries (not included) are required.

NOTE: Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.

To install batteries, remove keypad by rotating the cover counterclockwise, then

pulling toward you. (Fig. A) Unlock door with the override key provided in the plastic

bag attached to the owner’s manual, and open the door using the lever handle.

Remove key hook plate located on the inside back of the door by sliding the plate

upward, then pulling toward you. (Fig. B) Insert the four batteries as indicated.

Replace the key hook plate and keypad.

Test first with door open!

(See back cover of this manual for your factory code.)

Test your combination several times with the door open.

NOTE: All electronic lock units have been provided with an override key

(skeleton key). Some electronic units are equipped with a handle

OR electronic lock and key.

1. Insert the four-bitted key into the lock to the left of the key pad. (Be sure key

lock is turned as far left as possible.)

2. Press the five-digit factory code. The green light will come on.

3. For units with key, turn the key to the right.

4. Open the door.

Using the keypad

Only a light touch is needed. A green PROCEED light and a single beep indicate that

the keypad “felt” your touch. The lock allows 5 seconds for each key press. If you

pause longer, an error signal will occur (blinking red light and three beeps),

indicating you should start over.

Access Codes

There are three possible ways to unlock and access the safe—by entering its pre-

set Factory Code, your own User Code or a Passcode.

You can always open the safe by entering the 5-digit Factory Code. But if you prefer

to use your own code, you can program the safe to open to the 5-digit User Code of

your choice. If you wish to give someone else temporary access to the safe, you can

program a passcode that can later be erased.

Registration

www.registermysafe.com

Reasons to register

By registering your SentrySafe product you can easily retrieve forgotten

codes and combinations.

By registering your SentrySafe product you can be sure that in the unfortu-

nate circumstance of a ﬁre you will be guaranteed your replacement safe

(provided ofﬁcial paperwork has been completed).

Programming a user code

There are two ways to program a user code.

A 1. Press the Program key.

2. Enter the Factory Code. The green LED remains ON while you enter the

5-digit user code of your choice. After 5 digits are entered the green LED

turns OFF.

(To enter a new User Code, repeat these steps.)

B 1. Press the red button inside the safe. The lock will “beep” and the green

LED will come on.

2. Enter a 5-digit user code.

(To enter a new User Code, repeat these steps.)

Programming a passcode

1. Press the Program key twice.

2. Enter your 5-digit User Code. The green LED remains ON.

3. Enter the 5-digit passcode of your choice (any combination except 00000.) After 5

digits are entered, the green LED turns OFF.

(To enter a new passcode, repeat these steps. To erase the passcode, press

Program twice, enter your User Code and then enter 00000.)

Unlocking

To unlock the safe, you must enter a valid Factory Code, User Code or Passcode.

Once you have done this, you have 4 seconds to open the safe by turning the

handle or 4-bitted key to the unlock position. If you fail to do so in time, the lock

will reactivate.

(If you realize you have made an error while entering your code, press the CLEAR

button and start over.)

Key override

If your electronic lock fails or you do not have any codes available, you may use a key

override to access this unit. Remove the keypad by rotating the cover counterclock-

wise, then pull toward you. Unlock the door by inserting the key provided into the

hole and turning clockwise. Open the door. Do not lock override key inside of unit.

Signals

Your electronic-lock safe communicates by means of several audio/visual signals.

Red (Error) LED + three beeps indicates one of the following:

1. You have pressed Program key out of sequence

2. You have entered an invalid code or passcode.

3. You have let 5 seconds or more elapse between key entries.

Green (Proceed) LED + single beep occurs

1. After entering each digit of Factory or User Code, or Passcode

2. After pressing Clear key

3. After pressing Program key

Green LED only

1. Comes ON after you enter a valid code/passcode and remains lit during the 4-sec-

ond period in which the safe can be opened.

2. Comes ON in the Program User Code mode after you enter the Factory Code and

remains lit until you have finished entering a 5-digit User Code.

3. Comes ON in the Program Passcode mode after you have entered your User Code

and remains ON until you have entered a 5-digit passcode. Indicates “low battery”

and will typically not turn OFF until new alkaline batteries are installed.

Your electronic lock automatically performs a low battery test during each lock use.

If a “low battery” condition is detected, the Yellow LED will come ON and remain

ON during each subsequent lock operation. (The lock will continue to function in

a Low Battery state, until battery failure.) The Yellow LED will turn OFF only after

three consecutive “Good Battery” readings or after the low batteries are replaced.

(Note: When the new batteries are installed, the Yellow LED may come ON and stay

ON during the first lock operation before it returns to OFF.)

NOTE: When changing the batteries, you must use the factory code to open.

(See back cover.) Passcode will have to be re-programmed.

Delay Mode

The lock automatically enters a two-minute Delay Mode after an invalid code has

been entered three consecutive times. In this mode, the lock cannot be activated

and any key entry will generate an ERROR signal.

Bolt-down Instructions

1. Select a suitable and convenient location for your safe. Set the safe in place and

use the holes provided in the bottom or back of the safe to mark the location of

the holes to be drilled in the floor or wall. It is not recommended to attempt to

bolt to both floor and wall. If bolting to a wall, please ensure that the safe is rest-

ing on a supporting surface, i.e. floor, table or shelf.

2. Move the safe away and drill holes of the appropriate diameter and depth for the

type of hardware being used and the mounting surface.

3. Place the safe back over the holes and install the fasteners as required.

4. NOTE: For maximum security on models which have feet, remove feet before

bolting to floor.

Produkt Specifikationer

Mærke:	SentrySafe
Kategori:	Vault
Model:	T8-311

Har du brug for hjælp?

Hvis du har brug for hjælp til SentrySafe T8-311 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vault SentrySafe Manualer

SentrySafe FPW082HTC Manual

1 Oktober 2024

SentrySafe FPW082KSB Manual

1 Oktober 2024

SentrySafe S6370 Manual

1 Oktober 2024

SentrySafe FPW082KS Manual

1 Oktober 2024

SentrySafe FPW082HSB Manual

1 Oktober 2024

SentrySafe FPW082E Manual

1 Oktober 2024

SentrySafe FPW082ES Manual

1 Oktober 2024

SentrySafe Fire Chest 1160 Manual

1 Oktober 2024

SentrySafe FHW40300 Manual

1 Oktober 2024

SentrySafe Fire/Water Chest CHW20101 Manual

1 Oktober 2024

Vault Manualer

Nyeste Vault Manualer

Dometic ProSafe MD283 Manual

1 April 2025

Dometic ProSafe MD383 Manual

1 April 2025

Dometic ProSafe MD408 Manual

1 April 2025

Burg Wächter V-PZ 6900 Manual

27 Marts 2025

Phoenix SS0721EP Manual

11 Januar 2025

Phoenix Fire Fighter II FS0442E Manual

11 Januar 2025

Olympia GOsafe H20 Manual

11 Januar 2025

SereneLife SLSV45EQG Manual

11 Januar 2025

Kogan KADSAFM16LA Manual

8 Januar 2025

MSW -FPS-02 Manual

31 December 2025