THREE-YEAR LIMITED WARRANTY
The Three (3) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja
Operating LLC. Warranty coverage applies to the original owner and to the original product only and is
not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period
of three (3) years from the date of purchase when it is used under normal household conditions and
maintained according to the requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will
be repaired or replaced up to three (3) years from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the
receipt date of the replacement unit or the remainder of the existing warranty, whichever is later.
SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts which require regular maintenance and/or replacement to
ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are
available for purchase at sharkaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes.
3. Damage caused by misuse, abuse, negligent handling, failure to perform required maintenance
(e.g., not cleaning the filters or not removing debris from the hand tool or hose), or damage due to
mishandling in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages
caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts)
when the repair is performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal household conditions within
the warranty period, visit sharkclean.com/support for product care and maintenance self-help. Our
Customer Service Specialists are also available at 1-800-798-7398 to assist with product support and
warranty service options, including the possibility of upgrading to our VIP warranty service options
for select product categories. So we may better assist you, please register your product online at
registeryourshark.com and have the product on hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee
of $25.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of
purchase. We also ask that you register your product online at registeryourshark.com and have the
product on hand when you call, so we may better assist you. A Customer Service Specialist will provide
you with return and packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary from state to
state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so
the above may not apply to you.
1. Before storing, follow Maintenance and
Cleaning Instructions above. Be sure to
release all pressure from the hand tool by
placing it over a sink or toilet and pressing
the spray trigger until all liquid has been
released. Lay out all attachments to dry.
TECHNICAL SPECIFICATIONS
PX200 Series: 120V, 60Hz, 3.3A
2. Once dry, reattach all tools. Wrap up the
power cord, then store the hose-cleaning
tool on the unit. Wrap the hose around
the base of the unit and store the hand
tool in its holder.
© 2023 SharkNinja Operating LLC.
Needham, MA 02494/Ville St. Laurent, Québec H4S 1A7
1-800-798-7398
sharkclean.com
SHARK is a registered trademark of SharkNinja Operating LLC. STAINSTRIKER is a trademark of SharkNinja Operating LLC.
This product may be covered by one or more U.S. patents. See sharkninja.com/patents for more information.
Illustrations may dier from actual product.
STORAGE
RECORD THIS INFORMATION
Model Number: �����������������������������������������
Date of Purchase: ���������������������������������������
(Keep receipt)
Store of Purchase: ���������������������������������������
READ OWNER'S
MANUAL
CLEANING THE HOSE MAINTENANCE
1. When the Dirty Water Tank is full, there
will be a change in sound as the float
valve closes. Switch off the unit and
detach the tank, making sure to keep it
upright to prevent spills. Pull the handle
back, then lift off the lid. Pour out the
contents into a sink or toilet.
2. Remove the hand tool from the hose by
pressing the Detach Button . To (fig. 1)
clean the airpath in the tool, open the
cover (fig. 2). Aim the hand tool into a
sink or toilet and press the spray trigger
to release remaining pressure.
3. Clean the float valve by rinsing with
water under a tap. Make sure it can
move freely.
4. Remove the Dirty Water Tank. Clear
off any debris from the foam filter by
rinsing it under a faucet. Allow the filter
to air-dry completely, then reinstall it.
5. To clear any clogged debris at the end
of the hose, open the hose clog door on
the bottom of the unit. Clear all debris,
then close the door.
fig. 1 fig. 2
1. Make the sure the unit is turned off and
remove the CarpetXpert Tank. Fill tank
with water up to the Water fill line.
Tip: Add Deep Clean Pro to eliminate
odor.
WATER
CO NCENTRATE
1
2. Securely attach the Hose-Cleaning Tool to
the Crevice Tool and turn ON power. Pull
the trigger and cleaning solution will be
sucked into the hose to clean the interior.
22
5
TROUBLESHOOTING
Problem Solution
Inconsistent spray or no spray
Ensure there is cleaning formula in the CarpetXpert tank.
Make sure the CarpetXpert tank is installed correctly.
Make sure the unit is plugged in and the power is on.
Low suction or no suction
Make sure the dirty water tank is not overfilled.
Check the clog access door and clear any debris trapped
inside at the end of the hose.
If a cleaning tool is attached, make sure it is connected
correctly.
Remove any debris from the cleaning attachments.
Make sure the dirty water tank is installed correctly.
Unit not turning on
Make sure the unit is plugged in completely.
Try a dierent outlet.
Make sure the On/O switch is turned on.
Liquid leaking from unit
The dirty water tank may be overfilled.
Make sure the dirty water tank and the formula tank are both
installed correctly.
Make sure the float valve in the dirty water tank is not stuck.
Make sure the unit is on a stable, flat surface.
Make sure the hose clog door is closed completely
underneath the unit.
Solution tank leaking
Make sure the cap on the CarpetXpert tank is tightened
fully.
Make sure the CarpetXpert tank is installed correctly and
that the valve is in the tank.
Leaking from hand tool Ensure inside of Hand Tool or Pet Mess Tool is
thoroughly clean.
Tanks not dispensing liquid
Ensure CarpetXpert tank and StainStriker tank are both
installed correctly.
Note: Tanks dispense at dierent rates. CarpetXpert tank
will run out of solution before the StainStriker Tank.
1. The Pet Mess Tool is designed to tackle pet
messes while keeping debris and liquid out of
the interior of the Spot Cleaner (Pet Mess Tool
not included with some units. To order tools, visit
sharkaccessories.com. To use the Pet Mess Tool,
attach it to the Crevice Tool, then spray, scrub
gently to prevent squashing in cup, and extract
pet stains and messes. Keep the cup on the Pet
Mess Tool upright to avoid spillage.
2. Empty the cup after every use or when debris in
the cup reaches the MAX fill line. To empty, first
turn off power, then rotate the cup clockwise
and lift it off the tool. Empty the cup into sink or
trash. Lift the mesh filter, remove left side first,
then pull away to clean.
PET MESS TOOL
1
1
3. Be sure to rinse the Pet Mess Tool, cover,
rubber bristles mesh filter, and cup with soap
and water. Allow all parts to air-dry completely
before reassembling. Make sure the filter clicks
into place and to rotate the cup to the locked
position before use.
3
2
2
CLEANING FORMULAS
Deep Clean Pro Formula
The best deep carpet cleaning formula
for removing dirt & grime.
OXY Multiplier
The best tough stain-eliminating formula
for those stubborn stains and odors.
NOTE: Clean unit after every use to avoid odors, bacteria, and mold.
1
3
PX200Series�IB�MP�Mv20
Note: Pet Mess Tool MAX fill line holds 6oz,
if overfilled, liquid mess will enter hose and
into Spot Cleaner. Recommend to use Hose
Cleaning Tool to eliminate odor.
Note: The Pet Mess Tool is not intended to
clean pet hair.
Note: If your unit did not come with a Pet
Mess Tool, use the 3.5" hand tool with the
rubber bristles and follow Stain Guide.
4
