This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and
receiver.
●Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV
technician for help.
FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by
the manufacturer could void the user’s authority to operate
this equipment.
This device complies with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. It must not
be co-located or operating in conjunction with any other
antenna or transmitter.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment should be installed and operated with a
minimum distance of 20 cm between the radiator and
person’s body (excluding extremities: hands, wrists, feet
and ankles.)
The radio communications device incorporated into this
apparatus meets all requirements of the Industry Canada
Radio Frequency Exposure Rules RSS-210. This Class B
digital apparatus complies with the Canadian ICES-003
Class B specifications.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment should be installed and operated with a
minimum distance of 20 cm between the radiator and
person’s body (excluding extremities: hands, wrists, feet
and ankles.)
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of
uninsulated “dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
For your assistance in reporting this unit in case of loss
or theft, please record below the model number and
serial number which are located on the rear of the unit.
Please retain this information.
........................................................
........................................................
........................................................
........................................................
This reminder is provided to call the CATV system
installer’s attention to Article 820 of the National
Electrical Code that provides guidelines for proper
grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of
the building, as close to the point of cable entry as
practical.
Manufactured under license under U.S. Patent Nos:
5,956,674; 5,974,380; 6,487,535 & other U.S. and
worldwide patents issued & pending. DTS, the Symbol,
& DTS and the Symbol together are registered
trademarks & DTS Digital Surround and the DTS logos
are trademarks of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other
countries.
ENERGY STAR
®
Program Information
Products that have earned
the ENERGY STAR
®
are
designed to protect the
environment through
s guperior ener y efficiency.
ENERGY STAR® is a U.S. registered mark.
BA SS TR BLEE
A
UDI
O
3D
Note:
This product is recommended for flat panel TV (LED, LCD and plasma).
TINSZB335AWZZ
Pr nted n Malays ai i i
12G R AS 1
The following accessor es are i included.
BAS S TREBLE
A
UDIO
3D
The illustration below shows the flows of the signals.
1. Method 1
This connection is for HDMI TV with ARC (Audio Return Channel).
2. Method 2
This connection is for HDMI TV without ARC (Audio Return Channel).
●
This sound bar supports HDMI which enables ARC (Audio Return Channel).
●
To enable ARC make sure to use High Speed HDMI™ cable (with ARC).
●
This ARC feature requires TV that supports ARC. Refer the operation manual of the TV to determine which terminal supports ARC.
●
To listen to the sound from a non-ARC-compatible TV, connect the audio output from TV to this system’s. (refer page 10)
●
This sound bar can be operated (power on/off or volume up/down) via a TV or similar component which supports HDMI CEC (Consumer Electronics
Control). If this does not work, it does not mean this system is faulty. Refer to the operation manual of the respective component on how to activate the
CEC.
Example: Go to the Menu of the component to search and enable the CEC. Different brands may have different naming for the CEC. For SHARP LCD
TV, it is named as AQUOS LINK.
●
CEC is not available during Low power consumption mode.
●
●
●
To enjoy 3D images, this system must be connected to a 3D-compatible TV and components (3D BD player, etc.) via High Speed HDMI cables. Put on
the 3D glasses, otherwise 3D images may not be viewed properly.
●
If you want to use HDMI IN 1 jack, please use the supplied HDMI cable.
Turn off all other equipment before making this connection.
Press SOURCE button repeatedly until “HDMI 1”, “HDMI 2” or “TV ARC” appears on the display, or
press TV ARC button on the remote control to select the TV ARC.
DVD/Blu-ray
Digital tuner
TV
TV DVD, Blu-ray disc
player or similar
To HDMI output
terminal
To HDMI (TV ARC) input
terminal To HDMI
input
terminal
Sound Bar
To HDMI OUT (TV ARC) output terminal
TV DVD, Blu-ray disc
player or similar
To HDMI output
terminal
To HDMI input terminal
To HDMI input terminal
To HDMI OUT (TV ARC) output terminal Sound Bar
To audio output terminal
To Headphone
terminal
Installation image:
Place the system as shown.
Remove the protective film covering the sound bar and
subwoofer before turn on the system.
●
As the sound from the system is omni-directional, you can
place the sound bar anywhere you like. However, it is
recommended to place it as close to the TV as possible.
●
The front panel of the sound bar is not removable.
●Do not change the installation direction when the
sound
bar
is turned on.
●Do not stand or sit on the sound bar and subwoofer as
you may be injured.
●Do not allow any objects to fall into or to be placed in the bass reflex duct.
●Do not stand or sit on the sound bar/subwoofer. You may be injured.
Stand
AC I NP UT
P AIRI NG
Subwoofer
Sound Bar
AC outlet
AC 120 V ~ 60 Hz
AC outlet
AC 120 V ~ 60 Hz
DIGITAL
DIGITAL
1 2
3
AC INP UT
PA IRING
4
2
3
1
5
6
3
5
4
2
1
●Use the unit on a firm, level surface free from vibration.
●Keep the unit away from direct sunlight, strong
magnetic fields, excessive dust, humidity and
electronic/electrical equipment (home computers,
facsimiles, etc.) which generate electrical noise.
●Do not place anything on top of the unit.
●Do not expose the unit to moisture, to temperatures
higher than 140°F (60°C) or to extremely low
temperatures.
●If your system does not work properly, disconnect the
AC power cord from the AC outlet and replug.
●In case of an electrical storm, unplug the unit for safety.
●Hold the AC power plug by the head when removing it
from the AC outlet, as pulling the cord can damage
internal wires.
●The AC power plug is used as a disconnect device and
shall always remain readily operable.
●
●This unit should only be used within the range of 41°F -
95°F (5°C - 35°C).
●SHARP is not responsible for damage due to improper
use. Refer all servicing to a SHARP authorised service
center.
●The voltage used must be the same as that specified on
this unit. Using this product with a higher voltage other
than that which is specified is dangerous and may
result in a fire or other type of accident causing
damage. SHARP will not be held responsible for any
damage resulting from use of this unit with a voltage
other than that which is specified.
●In case of repairing, please bring the entire system set
to the service center.
The sound level at a given volume setting depends on
speaker efficiency, location and various other factors. It is
advisable to avoid exposure to high volume levels, which
occurs while turning the unit on with the volume control
setting up high, or while continually listening at high
volumes.
●Please ensure that the equipment is positioned in a
well-ventilated area and ensure that there is at least
4" (10 cm) of free space along the sides, top and back
of the equipment.
4" (10 cm)
4" (10 cm) 4" (10 cm)
4" (10 cm)
4" (10 cm) 4" (10 cm)
4" (10 cm)
1
3 4 5 876 9 10
2
Press and hold (MUTE) button on the remote control
until “TV SPEAKER” or “SB SPEAKER” appears on the
display to toggle sound output between this sound bar or
TV.
Note:
The backup function will protect the memorized function
mode for a few hours should there be a power failure or the
AC power cord becomes disconnected.
The audio return channel (ARC) function enables an HDMI
ARC-capable TV to send the audio stream to the HDMI OUT
jack of the receiver. To use this function, you must select the
TV ARC input and your TV must supports the ARC.
S+ 3D technology creates 3D sound through speakers
regardless of the type of sound source, whether it is
monaural, stereo or multichannel. It simulates sound
transmission characteristics using digital signal processing
to create a widening effect on the sound in the ambient
space around the sound source.
By using this technology, multichannel surround sound can
be produced from 2.1ch source.
Press the 3D AUDIO button repeatedly to select:
This product incorporates decoders supporting the Dolby
Digital system and DTS system.
You can operate Sharp TVs with this system’s remote
control.
The AV SYNC level can be
adjusted.
the level, press
the AV SYNC + button.
the level, press the AV SYNC – button.
When pressing the SOURCE button, the input source will
change. Press the SOURCE button repeatedly to select
desired input source, or
press TV ARC button on the remote control to select TV ARC.
This sound bar can be set to turn off automatically if no signal is
detected.
1. Press the APC button repeatedly to select the time.
2. The sound bar will enter the power stand-by mode automatically
if no signal is detected after the preset time has elapsed.
0 +1 +3
.....
TV ARCHDMI 2 OPTICAL AUDIO INHDMI 1
APC 15 min
PC 20 min
APC 10 minAPC 5 min
3D AUDIO 1 : Sound effect that emphasizes 3D
sound.
3D AUDIO 2 : Sound effect that maintains the 3D
sound and improve vocal clarity.
3D AUDIO OFF : 3D sound effect off.
One of the digital audio systems for theatrical
use. As the sound quality is emphasized, you
can enjoy the realistic sound effect in the home
theater system.
Lights up when detecting DTS signal.
One of the digital audio systems for theatrical
use. You can also enjoy the stereophonic effect
in the home theater system.
Lights up when detecting Dolby Digital signal.
This is a general term for digitally encoded audio
signals on a CD or DVD.
This sound bar lets you enjoy playback of digital
signals from sources such as CD or DVD.
Point the remote control at the TV.
Input Select Button
●When pairing is successful:
●If a device such as microwave oven, wireless LAN card,
Bluetooth device or any other device that uses the
same 2.4GHz frequency near the system, some sound
interruption may be heard due to interference.
●The transmission distance of the wireless signal
between the subwoofer and sound bar is about 32 feet
(10m), but may vary depending on your operating
environment. If a steel-concrete or metallic wall is
between the subwoofer and the sound bar, the system
may not operate at all, because the wireless signal
cannot penetrate metal.
●Keep the subwoofer away from water and moisture.
●To get the optimum listening performance, make sure
the area around the sound bar and subwoofer is clear
of any obstacles.
Press the DIMMER button to adjust the brightness of the
display.
If you turn off and on the sound bar with the volume set to
80 or higher, the volume starts at 40 and fades in to the last
set level.
Press the VOL + button to increase the volume and the
VOL – button to decrease the volume.
When the sound bar is turned off and back on again,
muting is canceled.
To change to a different mode, press the SOUND MODE
button repeatedly until the desired sound mode is
displayed.
Press the desired sound mode button on the remote
control.
●When sound from the speaker is distorted, decrease
the subwoofer level.
●When changing the subwoofer level, the output level of
the subwoofer is also changed.
On sound bar: “PAIRING” disappears.
On subwoofer: indicator turns blue.
Press the VOLUME +
button to increase the
volume and the VOLUME –
button for decreasing.
PA IRING
Sound Bar
Subwoofer
(
Display is dim
)
(Display gets dimmer)
(
Display is bright
)
Dimmer 1
Dimmer 2
Dimmer Off
Min Max
2 99
.....
1
The volume is muted temporarily when pressing the (MUTE)
button on the remote control. Press again to restore the volume.
CINEMA (for cinema sound effect)
MUSIC (for standard sound effect)
GAME (for game sound effect)
SPORT (for sport broadcasting)
NEWS (for news)
NIGHT (for night)
BYPASS (for flat sound effect)
Bass and Treble control is applicable during BYPASS
mode only.
1. Press the BASS button.
2. Within 5 seconds, press the VOL (+ or –) button to adjust
the bass.
1. Press the TREBLE button.
2. Within 5 seconds, press the VOL (+ or –) button to adjust
the bass.
The subwoofer level can be
adjusted.
the level,
press the SW LEVEL
button.
the level, press the SW LEVEL button.
+5–5 –4 +4
.....
Electricity is used to perform many useful functions, but it
can also cause personal injuries and property damage if
improperly handled. This product has been engineered
and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or
fire. In order to prevent potential danger, please observe
the following instructions when installing, operating and
cleaning the product. To ensure your safety and prolong
the service life of this product, please read the following
precautions carefully before use.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
Amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15) Power Sources - This product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or
local power company. For product intended to operate
from battery power, or other sources, refer to the
operating instructions.
16) Overloading - Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
17) Object and Liquid Entry - Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could
result in a fire or electric shock.
To prevent fire or shock hazard, do not expose this
appliance to dripping or splashing. No objects filled with
liquids, such as vases, shall be placed on the apparatus.
18) Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen
into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in
any way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
19) Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
20) Safety Check - Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
21) Wall or ceiling mounting - When mounting the product
on a wall or ceiling, be sure to install the product
according to the method recommended by the
manufacturer.
22) Power Lines - An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an
outside antenna system, extreme care should be
taken to keep from touching such power lines or
circuits as contact with them might be fatal.
23) Protective Attachment Plug - The product is equipped
with an attachment plug having overload protection.
This is a safety feature. See Instruction Manual for
replacement or resetting of protective device. If
replacement of the plug is required, be sure the
service technician has used a replacement plug
specified by the manufacturer that has the same
overload protection as the original plug.
24) Stand - Do not place the product on an unstable cart,
stand, tripod or table. Placing the product on an
unstable base can cause the product to fall, resulting
in serious personal injuries as well as damage to the
product. Use only a cart, stand, tripod, bracket or table
recommended by the manufacturer or sold with the
product. When mounting the product on a wall, be
sure to follow the manufacturer
’
s instructions. Use
only the mounting hardware recommended by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
The illustration below shows the flows of audio and video signals.
●Refer to the operation manual of the equipment to be connected.
●Fully insert the plugs to avoid fuzzy pictures or noises.
●Connecting via this method may disable TV internal speakers.
●In some cases, a small background noise could emit from the sound bar, when you use the headphone connection with
a TV-Set. In such case, please change the connection to the HDMI/ARC or RCA-connection. This effect depends on
the used TV-Brand, model and age, and it is not a quality matter from the sound bar.
Connect to the TV using an optical digital cable or an audio cable.
DVD/Blu-ray
Disc Player
Digital tuner, etc.
TV
Press SOURCE button repeatedly until “OPTICAL” appears on the display.
Press SOURCE button repeatedly until “AUDIO IN” appears on the display.
TV
Audio cable
(commercially
available)
To AUDIO IN
input terminals
Optical digital
audio cable
(commercially
available)
Sound Bar
Audio signal
To optical
digital audio
output
terminal
To audio output terminals
To
HEADPHONE
terminal
To OPTICAL
IN (optical)
input terminal
or
Blu-Ray/
DVD player/Digital
Tu ner
Some models of SHARP TV may not be operable.
2
3
4
5
7
8
10
12
13
1
9
11
6
15
16
17
18
19
20
21
23
22
24
25
14
AUDIO
TV Operation Buttons (Only SHARP TV):
On/Stand-by
Button
Sets the TV
power to
“ON” or
“STAND-BY”.
Input Select
Button (TV)
Press the
button to
switch the
input source.
Channel Up
and Down
Buttons
Switch up/
down the TV
channels.
Volume Up
and Down
Buttons
Turn up/
down the TV
volume.
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following
before calling your authorized SHARP dealer or service center.
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet or
on the transmitter on the remote control. Condensation can cause
the sound bar to malfunction. If this happens, leave the power on
until normal playback is possible (about 1 hour). Wipe off any
condensation on the transmitter with a soft cloth before operating the
sound bar.
When this product is subject to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
1. Set the sound bar to the stand-by mode and turn the power on
again.
2. If the sound bar is not restored in the previous operation, unplug
and plug in the sound bar again, and then turn the power on.
Make sure to disconnect all output and input cables attached to the
sound bar before performing the factory reset.
1. Press the ON/STAND-BY button to enter the power stand-by
mode.
2. While pressing the SOUND MODE button, press and hold the
ON/STAND-BY button until “RESET” appears.
3. This operation will erase all data stored in memory.
●
No sound is heard.
●
Is the input signal (selection)
set properly?
●
Is the volume level set to “Min”?
●
Is muting activated?
●
Is HDMI compliant equipment
being used?
●
Is the HDMI cable connected
correctly?
Connect the HDMI cable
correctly and then perform the
reset procedure. (refer this
page)
●
Do not connect or disconnect
an HDMI cable while power is
on. This may lead to operation
problems.
●
The sound from
subwoofer is not well
balanced.
●
Is the subwoofer level set to the
minimum or maximum level?
●
Power turns off
suddenly.
●
Is the HDMI cable connected
correctly? Connect the HDMI
cable correctly and then
perform the reset procedure.
●
Noise is heard during
playback.
●
Move the speaker away from
any computers or mobile
phones.
●
When a button is
pressed, the sound bar
does not respond.
●
Set the sound bar to the stand-
by mode and then turn it back
on.
●
The power is not turned
on.
●
Is the sound bar unplugged?
●
The protection circuit may be
activated. Unplug and plug in
the power cord again after 5
minutes or more.
●
3D images not displayed
on the TV.
●
Depending on the TV and
Video component, 3D images
may not be displayed.
Check the operation manual of
the respective component.
●
HDMI cable not support 3D
image.
●
Background noise
appears when
connecting with
headphone output of
TV-Terminal.
●
Please change to HDMI/ARC
or RCA-Output terminal from
TV-Set. This effect may occur
depending on TV-Brand, model
and age, and it is not the sound
bar problem.
●
Wireless connection
cannot be established.
●
Check the distance between
the sound bar and subwoofer
(less than 32 feet (10m)).
●
Make sure there is no other
wireless devices near the unit.
●
Make sure there is no obstacles
(especially metal) blocking
between the sound bar and
subwoofer.
●
Wireless connection
cannot be established.
●
Manually re-link the sound bar
and subwoofer (refer page 11).
●
The remote control does
not operate properly.
●
Is the battery polarity correct?
●
Is the battery dead?
●
Is the distance or angle
incorrect?
●
Are there any obstructions in
front of the sound bar?
●
Is there a strong light shining
on the remote sensor?
●
Is the remote control for
another equipment used
simultaneously?
●
The sound bar cannot
be turned on with the
remote control.
●
Is the AC power cord of the
sound bar plugged in?
●
Is the battery inserted?
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the
"Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will,
at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent
at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or
other misuse, abnormal service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide
proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law.
ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE
LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused
by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any
way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion
of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
Warranty Period for this Product:
Additional Item(s) Excluded from Warranty Coverage
(if any):
Where to Obtain Service:
What to do to Obtain Service:
HT-SB60 Sound Bar Home Theater System
(Be sure to have this information available when you need
service for your Product.)
One (1) year parts and labor from the date of purchase.
Non-functional accessories, supplies, and consumable
items.
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer,
call Sharp toll free at 1-800-BE-SHARP.
Ship prepaid or carry in your Product to a Sharp Authorized
Servicer. Be sure to have Proof of Purchase available. If
you ship the Product, be sure it is insured and packaged
securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
●Remove the battery if the sound bar will not be used for
a long period of time. This will prevent potential damage
due to battery leakage.
●Do not use rechargeable battery (nickel-cadmium
battery, etc.).
●Installing the battery incorrectly may cause the sound
bar to malfunction.
●Batteries (battery pack or battery installed) shall not be
exposed to excessive heat such as sunshine, fire or the
like.
●Replace the battery if the operating distance is reduced
or if the operation becomes erratic.
●Periodically clean the transmitter on the remote control
and the sensor on the sound bar with a soft cloth.
●Exposing the sensor on the sound bar to strong light
may interfere with operation. Change the lighting or the
direction of the sound bar.
●Keep the remote control away from moisture, heat,
shock, and vibrations.
Point the remote control directly at the remote sensor on
the sound bar.
Press the ON/STAND-BY button on the sound bar or the
remote control.
●The power turns on and the subwoofer indicator turns
blue. If the power does not turn on, check whether the
AC power cord is plugged in properly.
●The system will automatically power on if TV or similar
component which supports HDMI CEC, is turned on.
Press the ON/STAND-BY button again on the main unit or
the remote control and the subwoofer indicator turns red.
●A slight audio delay after TV is turned ON does not
mean that the system is faulty. This is normal.
●“AQUOS speaker is enabled” message will be
displayed if SHARP LCD TV does not detect HT-SB60
during power on. However the message “AQUOS audio
with AQUOS LINK is enabled” will be displayed soon as
HT-SB60 is detected. These messages may vary for
other TV model.
●The first time the unit is plugged in, the unit will enter
the demonstration mode.
●To cancel the demonstration mode, press the DEMO
button on the remote control during power stand-by
mode.
●To enter to the low power consumption mode, press
and hold the DEMO button.
The sound bar and subwoofer will link automatically
(wirelessly) when turned on as it is already pre-linked at
the factory. If the link cannot be established, please set the
connection by the following method.
1. Press and hold the PAIRING button on the sound bar for
more than 3 seconds.
2. Within 2 minutes, press and hold the PAIRING button on
the subwoofer for more than 3 seconds.
●During pairing process:
Use 1 “AA” size battery (UM/SUM-3, R6, HP-7 or
similar). Batteries are not included.
When inserting or removing the battery, push them
toward the battery terminals.
Remote sensor
8" - 20"
(0.2 m - 6 m) 15°15°
On sound bar: “PAIRING” will blink.
On subwoofer: indicator will blink in blue.
AUDI O
●Be very careful to prevent the sound bar [7.92 lbs. (3.6 kg)]
from falling when mounting on the wall.
●Before mounting, check the wall strength. (Do not put
on the veneer plaster or whitewashed wall. The sound
bar may fall.) If unsure, consult a qualified service
technician.
●Mounting screws are not supplied. Use appropriate
ones.
●Check all wall mount angle screws for looseness.
●Select a good location. If not, accidents may occur or
the sound bar may get damaged.
●
SHARP designed the sound bar so you may hang them on
the wall. Use proper screws (not supplied). See below for
size and type.
Make sure all screws are fully tightened. (screws are not
supplied)
Safety wires (not supplied) are useful to prevent the sound
bar from falling off the table.
Loop the safety wires (not supplied) into each hole as
shown and tie the safety wires to the LCD TV stand.
1/8" (3.2 mm)
3/8" (9 mm)
7/8" (Min. 22 mm)
3/16"
(5 mm)
Pattern paper
Wall surface
29 mm
44 mm
926 mm 44 mm
29 mm
Wall surface
3/8" (8-9 mm)
1-1/4" (32 mm)
Wall surface
3/8" (8-9 mm)
1-1/4" (32 mm)
Wall surface
Wall mount angle
Wall mount
angle Wall
surface
Wall surface
Wall
mount
angle
(screws x 4)
(screws x 4)
Wall surface
Periodically wipe the cabinet with a soft cloth.
●Do not use chemicals for cleaning (gasoline, paint
thinner, etc.). It may damage the cabinet finish.
●Do not apply oil to the inside of each component. It may
cause malfunctions.
When you fail to perform operations properly, the following
messages are displayed on the sound bar.
(*):
Should the same message appear even if the speaker is
unplugged and plugged in, or is set to the stand-by mode
and on again, contact your local dealer where you
purchased the sound bar.
As part of our policy of continuous improvement, SHARP
reserves the right to make design and specification changes
for product improvement without prior notice. The
performance specification figures indicated are nominal
values of production unit. There maybe some deviations
from these values in individual unit.
●Malfunction of the surround
circuit. Place the speaker
away from noise source and
plug the AC power cord into
another AC outlet. (*)
(Display blinks)
●When there is no input signal.
Play back the connected
equipment.
●Nonstandard signal. Cannot
be recognized.
●Signals other than DOLBY
DIGITAL, DTS, Linear PCM
cannot be recognized.
●Poor connection of the digital
audio input terminal.
●Turn off the sound bar and
check if the cable is
connected properly.
Demo indicator
(blinks red)
●When the protection circuit is
activated.
or
or
or
AC 120 V ~ 60 Hz
38 W
Width: 54 - 1/2" (1385 mm)
Height: 2 - 7/8" (73 mm)
Depth: 2 - 11/16" (68 mm)
7.92 lbs. (3.6 kg)
Total 160 watts
Front Left/Right:
80 watts per channel into 4 ohms at
1 kHz, 10% total harmonic distortion
FTC:
Front: (Left/Right):
Minimum 50 watts per channel into
4 ohms at 120 Hz to 20 kHz, 1% total
harmonic distortion
HDMI™ output: (audio/video support up
to 1080p) x 1
Analog input (AUDIO IN): x 1
500 mV / 47 kohms
Optical digital input (OPTICAL):
Square type x 1
HDMI input: (audio/video support up to
1080p) x 2
2 Way speaker system
2 -1/4" (5.7 cm) woofer
1" (2.5 cm) Soft Dome
160 W
80 W
4 ohms
AC 120 V ~ 60 Hz
33 W
RMS:
150 watts per channel into 3 ohms at
100 Hz, 10% total harmonic distortion
FTC:
Minimum 110 watts per channel into
3 ohms at 100 Hz, 1% total harmonic
distortion
Subwoofer system
6 - 5/16" (16 cm) woofer
300 W
150 W
3 ohms
Width: 5 - 11/16" (144 mm)
Height: 16 - 15/16" (430 mm)
Depth: 12 - 1/16" (306 mm)
13.42 lbs. (6.1 kg)
HT-SB60 EN (A1).indd 1
HT-SB60 EN (A1).indd 1
HT-SB60 EN (A1).indd 1
HT-SB60 EN (A1).indd 1HT-SB60 EN (A1).indd 1 7/4/2012 2:2
7/4/2012 2:2
7/4/2012 2:2
7/4/2012 2:2 :44 PM
:44 PM
:44 PM
:44 PM
9
9
9
97/4/2012 2:2 :44 PM9
