Shimano BB-7700 Manual

Shimano Cykel tilbehør BB-7700

Læs gratis den danske manual til Shimano BB-7700 (2 sider) i kategorien Cykel tilbehør. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Shimano BB-7700, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Bottom Bracket
BB-7700
BB-7703
Before use, read these instructions carefully, and follow them for
correct use.
BB-7700
Shell width
Bottom Bracket
109.5mm
Spindle length
BB-7703
118.5mm
SERVICE INSTRUCTIONS
SI-1TG0H-001
Note
* Check that the fixing bolt of the bottom bracket cable
guide is not so long that it touches the inner cover. If the
fixing bolt touches the inner cover, it may damage the
inner cover, which will result in a drop in waterproofing
performance.
* Apply grease to the R.H. adapter and L.H. adapter before
installing them to the hanger.
* Apply grease to the surface which contacts the crank arm
before installing the crank arm.
* For maximum performance we highly recommend
Shimano lubricants and maintenance products.
Installation of the Bottom Bracket (BB-7700)
1. Insert the main unit into the
hanger. After checking that
the inner cover is securely
attached to the R.H. adapter,
place them onto the hanger.
2. Tighten the right-hand adapter
by turning it counterclockwise
using the special tool (TL-FC31).
(clockwise for 70 mm [M36]
bottom brackets)
Tightening torque:
50 - 70 Nm
{435 - 608 in. lbs.}
Inner cover
R.H. adapter
3. Use the special tool (TL-UN74-S)
to tighten the left-hand adapter
clockwise until the spindle
turning effort increases sharply.
After tightening the left-hand
adapter, loosen it by about 1/16
to 1/8 of a turn so that the
spindle rotates smoothly.
5. Apply grease to the seal guards and then attach the seal
guards to the spindle, while making sure that the grooves of
the seal rings face inward. If the grooves face outward
after the seal rings are installed, the water-tightness
will drop significantly. (The seal guards are
pushed into the proper
positions when the crank
arms are installed, so do
not force the seal rings on
when installing them.)
6. Install the right-hand crank arm, and then check that there is
no play in the bearing cone is adjusted correctly. If there is
some play in the bearing cone, loosen the lock ring and then
tighten the left-hand adapter by as little as possible. Repeat
steps 4 and 6 until there is no more play.
4. Use the special tool (TL-FC31) to tighten the lock ring while
using the special tool (TL-UN74-S) to push in the left-hand
adapter.
Left Right
Seal guard Seal guard
Grease
Maintenance
●Apply grease to each part at periodic intervals. (Refer to the illustration.)
●Water can get inside the bottom bracket. If using a frame which does
not have water drainage holes in the hanger, be sure to drain any water
which has collected inside the hanger before removing the bottom
bracket.
Please note: specifications are subject to change for improvement without notice. (English)
© Nov. 2007 by Shimano Inc. XBC SZK Printed in Singapore
Groove
TL-FC31
R.H. adapter
TL-UN74-S
Lock ring
TL-FC31
Tightening torque:
50 - 70 Nm {435 - 608 in. lbs.}
Specifications
• Obtain and read the service instructions carefully
prior to installing the parts. Loose, worn, or damaged
parts may cause injury to the rider. We strongly
recommend only using genuine Shimano
replacement parts.
WARNING
SEALED
CARTRIDGE UNIT
BB-7700
JAPAN VIA
109.5
R
L
J
A
A
P
N
B
C
1
.
3
7
68
BB
-
77
00
LR
Apply grease
Inner cover
1. Use the special tool (TL-UN74-
S) to install the bottom
bracket. First install the main
body (clockwise for 70 mm
[M36] bottom brackets), then
the adapter.
Installation of the Bottom Bracket
(BB-7703)
Left
Bottom bracket
Right
Apply grease to
the bottom bracket
before installing it.
Adapter/bottom bracket
tightening torque:
50 - 70 Nm {435 - 608 in. lbs.}
TL-UN74-S
Lock ring
Left-hand adapter
68mm (BC1.37), 70mm (M36)

Produkt Specifikationer

Mærke: Shimano
Kategori: Cykel tilbehør
Model: BB-7700

Har du brug for hjælp?

Hvis du har brug for hjælp til Shimano BB-7700 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Cykel tilbehør Shimano Manualer

Shimano

Shimano ST-R9100-L Manual

30 December 2025
Shimano

Shimano SH-TR500 Manual

30 December 2025
Shimano

Shimano FD-M8000-L Manual

4 Oktober 2024
Shimano

Shimano FD-M6020-L Manual

30 September 2024
Shimano

Shimano SM-RT70 Manual

16 September 2024
Shimano

Shimano SM-CA70 Manual

14 September 2024
Shimano

Shimano PD-M324 Manual

11 September 2024
Shimano

Shimano Deore XT PD-M8120 Manual

6 September 2024
Shimano

Shimano SL-3S41E Manual

5 September 2024
Shimano

Shimano ST-M4000-L Manual

13 August 2024

Cykel tilbehør Manualer

Nyeste Cykel tilbehør Manualer

Knog

Knog Oi Luxe Manual

26 September 2024
Lezyne

Lezyne Trigger Drive CO2 Manual

24 September 2024
Giant

Giant Downtown Manual

14 September 2024
Knog

Knog Milk Man Manual

13 September 2024
Thule

Thule Lock Kit Manual

13 September 2024
Abus

Abus WBA65 Manual

5 September 2024
Topeak

Topeak PRESSURE-RITE SHOCK ADAPTER Manual

5 September 2024
Funn

Funn Ripper Manual

2 September 2024
Funn

Funn Mamba Manual

2 September 2024
Basil

Basil Bremen Manual

31 August 2024