Shimano BR-IM35 Manual

Shimano Ikke kategoriseret BR-IM35

Læs gratis den danske manual til Shimano BR-IM35 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Shimano BR-IM35, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INTER M Brake

IMPORTANT NOTICE

•Contact the place of purchase or a distributor for information on installation,

adjustment, and replacement of the products which are not found in the user's

manual. A dealer's manual for professional and experienced bicycle mechanics is

available on our website (https://si.shimano.com).

For safety, be sure to read this “user's manual” thoroughly

before use, follow it for correct use, and store it so that it

can be referenced at any time.

The following instructions must be observed at all times in order to prevent

personal injury and physical damage to equipment and surroundings. The

instructions are classified according to the degree of danger or damage which may

occur if the product is used incorrectly.

DANGER Failure to follow the instructions will result in

death or serious injury.

WARNING Failure to follow the instructions could result in

death or serious injury.

CAUTION

Failure to follow the instructions could cause

personal injury or physical damage to equipment

and surroundings.

Important safety information

WARNING

•Because each bicycle may handle slightly differently depending on the model, be

sure to learn the proper braking technique (including brake lever pressure and

bicycle control characteristics) and operation of your bicycle. Improper use of your

bicycle's brake system may result in a loss of control or a fall, which could lead to

severe injury.

•Do not disassemble or modify the product. This may cause the product to not

operate correctly, and you may suddenly fall and be seriously injured.

•It is necessary to use the brake caliper of the SHIMANO front INTER M brake and

the hub as a set (excluding BR-C6050-F/BR-C6060-F). The hub of the SHIMANO

front INTER M brake has a built-in power modulator. This system controls the

braking force so that excessive force is not applied if the braking force reaches

the specified value. If the front brake is applied too strongly in the case that the

hub is not equipped with a power modulator or the hub is equipped with a

power modulator but the overall mass does not meet the recommended mass,

the front wheel may lock and the bicycle may fall forward, and serious injury may

result. Noise is generated by the operation of the power modulator when the

brake is applied, but this is not a sign of a malfunction.

•The range of overall allowable mass (bicycle + rider + luggage) of the BR-C6050-F/

BR-C6060-F power modulator

Model name Outer diameter of tire

(mm)

Range of overall allowable

mass (kg)

BR-C6050-F 660 - 712 70 - 100

BR-C6060-F 660 - 712 100 - 130

•Use the BR-C6050-F or BR-C6060-F power modulator within its range of overall

allowable mass. If the overall mass is out of the allowed range, the controlled

braking force may be too strong or too weak.

•A wet road surface may cause tires to lose traction; therefore, to avoid this,

reduce your speed and apply the brakes early and gently. If the tires lose traction,

you may fall and be seriously injured.

CAUTION

•Do not continuously apply the brakes when riding down long slopes. For the

SHIMANO INTER M brake system, this will cause the internal brake parts to

become very hot, weakening braking performance, as well as causing a reduction

in the amount of brake grease inside the brake, which can lead to noise being

generated or problems such as abnormally sudden braking.

•If any of the following occur while using the brakes, stop riding immediately and

ask the place of purchase to carry out inspection and repairs.

1. An abnormal noise is heard when the brakes are applied.

2. The braking performance is abnormally strong.

3. The braking performance is abnormally weak.

If 1 and 2 occur, the cause might be a lack of brake grease, so ask the place of

purchase to grease the mechanism with special roller brake grease.

If 2 and 3 occur when using BR-C6050-F/BR-C6060-F, the power modulator may be

malfunctioning. Have it inspected/repaired at the place of purchase.

•Do not touch the area around the brake for at least 30 minutes after riding the

bicycle. If the brake is used frequently, the area around the brake may become

hot.

Area around the brake

•Check the brake cable for rust. If the brake cable becomes rusty, braking

performance will suffer. If this happens, replace the brake cable with a genuine

SHIMANO brake cable and re-check braking performance.

•The front brake unit and front hub unit should never be disassembled. If it is

disassembled, it may no longer work properly.

Notice

•If you apply the front INTER M brake strongly while the bicycle is stopped then

shake the wheel, you will notice that there is a small amount of gap in the brakes.

This is normal, and will not cause any problems at all while riding.

•Products are not guaranteed against natural wear and deterioration from normal

use and aging.

•For maximum performance we highly recommend SHIMANO lubricants and

maintenance products.

Regular inspections before riding the bicycle

Before riding the bicycle, check the following items. If any problems are found,

consult your place of purchase or a distributor.

•Do the front and rear brakes work correctly?

•Are there any abnormal noises?

•Is the braking performance abnormally strong?

•Is the braking performance abnormally weak?

•Does the brake cable have any rust?

Names of parts

Front Rear

Brake cable Brake cable

UM-8M30A-006 User's Manual

Please note: specifications are subject to change for improvement without notice. (English)

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

High Tech Campus 92, 5656 AG Eindhoven, The Netherlands Phone: +31-402-612222

3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan

Produkt Specifikationer

Mærke:	Shimano
Kategori:	Ikke kategoriseret
Model:	BR-IM35

Har du brug for hjælp?

Hvis du har brug for hjælp til Shimano BR-IM35 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Shimano Manualer

Shimano FC-MT610-B2 Manual

11 Januar 2025

Shimano ST-T4000-R Manual

30 December 2025

Shimano BR-M8120 Manual

7 Oktober 2024

Shimano SL-RV400-6R Manual

7 Oktober 2024

Shimano SL-RV300-6R Manual

6 Oktober 2024

Shimano ST-2400-R Manual

6 Oktober 2024

Shimano CN-HG901-11 Manual

6 Oktober 2024

Shimano DH-T785 Manual

4 Oktober 2024

Shimano CLARIS 2400 ST-R240-R Manual

1 Oktober 2024

Shimano SL-RV300-7R Manual

1 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor SP-CAG-435320 Manual

1 December 2025

Vevor LX-PMMA-36*48 Manual

1 December 2025

Vevor TC2135 Manual

1 December 2025

Vevor PFFSTGSH08 Manual

1 December 2025

Microchip M1A3P600L Manual

1 December 2025

1 December 2025

1 December 2025

1 December 2025

1 December 2025

1 December 2025