Shimano SM-AX720-142x12 Manual

Shimano Ikke kategoriseret SM-AX720-142x12

Læs gratis den danske manual til Shimano SM-AX720-142x12 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Shimano SM-AX720-142x12, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
On d, vin i , .S. n - 3e Hollan Ir e, Californ a 92618 U A. Pho e: +1 949-951-500
Industriew g 24 80 CT Nu speet, The therlan s Ph ne +31-341-27 22e , 71 n Ne d o : 2 2
3-77 Oimatsu-cho Sa ai-ku, kai-s Osaka 590 8577, Japa , k Sa hi, - n
Please note: specifications are subject to change for improvement without notice. (English)
© Dec. 2015 by Shimano Inc. HTR
UM-2AC0A-000-00 User's manual
E-THRU Axle (12 mm)
User's manuals in other languages are available at :
http://si.shimano.com
IMPORTANT NOTICE
•Contact the place of purchase or a bicycle dealer for information on
installation and adjustment of the products which are not found in
the user's manual. A dealer's manual for professional and experienced
bicycle mechanics is available on our website (http://si.shimano.com).
•Do not disassemble or alter this product.
For safety, be sure to read this user's manual thoroughly
before use, and follow it for correct use.
Important Safety Information
For replacement information, contact the place of purchase or a bicycle
dealer.
WARNING
•
BEFORE USE, CAREFULLY READ AND FOLLOW THE INSTRUCTIONS ON
THE E-THRU AXLE (12MM) SYSTEM IN THIS USER'S MANUAL. IF YOU
HAVE ANY QUESTIONS, ASK YOUR DEALER.
•The E-THRU axle (12mm) may be used in combination with the special
frame and special hub/wheel only. If it is used in combination with
any other frame or hub/wheel, it may cause the wheel to become
detached from the bicycle while you are riding and result in serious
bodily injury.
•If the E-THRU axle (12mm) is not correctly installed on the bicycle, the
wheel may detach from the bicycle while riding, resulting in serious
injury.
•
If the E-THRU lever is on the left side
(rotor side) of the frame, make sure that
the E-THRU lever does not interfere with
the rotor (Figure 1). In addition, make
sure that the E-THRU lever does not
interfere with the frame, other parts,
accessories, etc., or come into contact
with obstructions (such as shrubs and
rocks) while riding. If the E-THRU lever
loosens owing to interference or contact
with foreign objects, the wheel will
loosen and begin to rattle. If this occurs,
contact the place of purchase or a bicycle
dealer. Riding the bicycle while the wheel
remains loose may lead to the bicycle
collapsing and result in serious injury.
E-THRU
lever
Disc brake rotor
CLOSE position
Figure 1
•Do not touch the disc brake rotor while handling the E-THRU system.
In addition, do not operate the E-THRU lever while the wheel is
turning. The disc brake rotor is very sharp and serious injury may
occur as a result of touching it.
•The brake calipers and disc brake rotor become very hot when the
brakes are being used. To avoid the danger of burns, be sure to check
that they have cooled down suffi ciently after riding the bicycle before
handling the E-THRU system.
•Before installing the wheel, remove any foreign particles and dust
from the fork end hole, the frame-side thread, and the axle openings.
Foreign particles or dust may interfere with the correct installation of
the E-THRU system, and if the hub and axle are not installed correctly,
the wheel may come off and serious injury may occur as a result.
•The adjuster cannot rotate more than 3 turns.
Do not turn the adjuster forcibly in either the tightening or loosening
direction when the rotation of the adjuster feels heavy. Forcibly
turning the adjuster may damage it.
•If the bicycle is ridden without an adjuster, there are cases where
subsequently adjustment becomes impossible; therefore, be sure to
replace the E-THRU axle with a new one.
•After reading the user's manual carefully, keep it in a safe place for
later reference.
Note
•Always check the E-THRU hubs before riding to make sure the wheels
are correctly installed on the frame. This is especially important after
you park your bicycle in a public place.
•
Make sure that the E-THRU levers are pushed fully to the CLOSE position
(the side of the lever with the inscription "CLOSE" must be facing away
from the bicycle). As show in the fi gure, tilt the levers. Do not rotate them.
OPEN position
CLOSE position
•In the case of replacing the E-THRU lever axle with another one, make
sure that the one replacing the existing E-THRU lever axle is the same
in model name as the E-THRU model provided on the frame.
If the model name is different, the replacing E-THRU lever axle may
not be mounted correctly onto the frame due to differences in axial
length, thread size, housing diameter, etc.
•Products are not guaranteed against natural wear and deterioration
from normal use and aging.
•For maximum performance we highly recommend Shimano lubricants
and maintenance products.
Regular inspections before riding the bicycle
Before riding the bicycle, check the following items. If any problems are found
with the following items, contact the place of purchase or a bicycle dealer.
•Are the wheels correctly installed to the frame?
•Are the E-THRU levers fully pushed to the CLOSE position?
QUICK CHECK
Lift up the bicycle so that the wheel is off the ground, and give the top
of the tire a few sharp downward blows as shown in Figure 1. Also
shake the wheel from side to side as shown in Figure 2 to make sure
that there is absolutely no looseness in the wheel. This check does not
guarantee that the E-THRU lever has received adequate tightening
torque. If you are uncertain as to whether the E-THRU lever is tightened
correctly, repeat the installation procedure as explained in "Installing
the wheel" in these Service Instructions before riding the bicycle.
Figure 1 Figure 2
Names of parts
Axle opening
Hub shoulder
Adjuster
E-THRU lever
Fork end
Operation
NOTICE
•Always be sure to operate the E-THRU lever with your hand. Never
use a hammer or other object to close the lever. If this is not observed,
the E-THRU system or the frame may be damaged.
What is the E-THRU hub?
It is a mechanism that uses the E-THRU lever on the hub to easily install
and remove the wheel.
E-THRU hub function
Tilt the E-THRU lever toward the CLOSE position and clamp the frame to
secure the wheel in the correct position.
CLOSE position
E-THRU lever
OPEN position
Installing the wheel
1. Align the hub shoulder correctly
with the fork end.
Hub
shoulder
Fork end
2.
Move the E-THRU lever to the
OPEN position, and insert it into
the hole in the fork end on the
side opposite to where the thread
is. Pass the lever axle all the way
through until it reaches the thread
part on the other side.
3.
Turn the E-THRU lever to screw the E-THRU lever axle into the frame-
side thread.
Open and close the E-THRU lever; tighten the E-THRU lever axle into
the frame-side thread until some resistance is felt when the E-THRU
lever is parallel to the hub axle while being moved toward the
CLOSE position.
1
2
OPEN position
Checking
position
CLOSE position
4.
For safety, make sure that the E-THRU lever runs along the frame when
it is in the CLOSE position. Using just the force of your hand, push the
E-THRU lever with the palm of your hand until it moves all the way to
the CLOSE position. Check that the side of the E-THRU lever with the
inscription 'CLOSE' is facing away from the bicycle.
Make sure that the E-THRU lever is not interfering with the frame, other
parts, accessories, etc. In addition, be careful that it does not come into
contact with obstructions (such as shrubs and rocks) while riding. If the
E-THRU lever is not positioned correctly, the adjuster needs to be
adjusted. For adjustment procedures, refer to "Adjusting the adjuster".
E-THRU
lever
Disc brake
rotor
CLOSE position
Tightening torque:
5 - 7.5 N·m
If there are any instructions on the tightening position for the E-THRU
lever in the Service Instructions, follow them when tightening.
Removing the wheel
Move the E-THRU lever from the CLOSE position to the OPEN position,
and then turn the E-THRU lever counterclockwise to remove the E-THRU
axle from the frame-side thread. Once the E-THRU axle has been removed
from the frame-side thread, remove the E-THRU axle from the wheel.
Adjusting the adjuster
1. Screw the E-THRU lever axle into the frame-side thread in step 3 of
Installing the Wheel, then turn the E-THRU lever to adjust it so that it
moves to the correct CLOSE position, and check the torque.
2. •
If the tightening torque is weak when moving the E-THRU lever to
the CLOSE position, turn the adjuster in the direction of the arrow.
Fixing torque: Stronger
Adjuster
•
If the tightening torque checked in step 1 is so strong that the E-THRU lever
cannot be easily moved to the CLOSE position, turn the adjuster in the
direction of the arrow to make it weaker. Loosen the adjuster gradually in
stages up to the point where it would require the full exertion of your
strength to close the E-THRU lever.
Fixing torque: Weaker
Adjuster
3. Repeat this adjustment until the correct installation force is obtained
at the correct lever position.

Produkt Specifikationer

Mærke: Shimano
Kategori: Ikke kategoriseret
Model: SM-AX720-142x12

Har du brug for hjælp?

Hvis du har brug for hjælp til Shimano SM-AX720-142x12 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Shimano Manualer

Shimano

Shimano FC-MT610-B2 Manual

11 Januar 2025
Shimano

Shimano ST-T4000-R Manual

30 December 2025
Shimano

Shimano BR-M8120 Manual

7 Oktober 2024
Shimano

Shimano SL-RV400-6R Manual

7 Oktober 2024
Shimano

Shimano SL-RV300-6R Manual

6 Oktober 2024
Shimano

Shimano ST-2400-R Manual

6 Oktober 2024
Shimano

Shimano CN-HG901-11 Manual

6 Oktober 2024
Shimano

Shimano DH-T785 Manual

4 Oktober 2024
Shimano

Shimano CLARIS 2400 ST-R240-R Manual

1 Oktober 2024
Shimano

Shimano SL-RV300-7R Manual

1 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor

Vevor SP-CAG-435320 Manual

1 December 2025
Vevor

Vevor LX-PMMA-36*48 Manual

1 December 2025
Vevor

Vevor TC2135 Manual

1 December 2025
Vevor

Vevor PFFSTGSH08 Manual

1 December 2025
Microchip

Microchip M1A3P600L Manual

1 December 2025
DVDO

DVDO Air 2K Manual

1 December 2025
Vevor

Vevor C4++ Manual

1 December 2025
Vevor

Vevor CD-HG05 Manual

1 December 2025
Vevor

Vevor SBC90 Manual

1 December 2025
Vevor

Vevor JD342 Manual

1 December 2025