Shure BETA 52A Manual

Shure Mikrofon BETA 52A

Læs gratis den danske manual til Shure BETA 52A (12 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 85 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 43 anmeldelser. Har du et spørgsmål om Shure BETA 52A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

Model BETA 5 2®A Use r Gui de

27D2799 (Rev. 5) Printed in U.S.A.

SUPERCARDIOID DYNAMIC INSTRUMENT

MICROPHONE

GENERAL

The Shure BETA 52®A is a high output dynamic microphone

with a tailored frequency response designed speci cally for kick ﬁ

drums and other bass instruments. It provides superb attack and

“ ”punch, and delivers studio quality sound even at extremely high

sound pressure levels.

The BETA 52A features a modi ed supercardioid pattern through-ﬁ

out its frequency range to insure high gain before feedback and

excellent rejection of unwanted sound. A built in dynamic locking –

stand adapter with an integral XLR connector simpli es installa-ﬁ

tion, particularly if the microphone is to be placed inside a kick

drum. The stand adapter keeps the microphone position ﬁxed and

resists slipping, even when subjected to sharp blows and strong

vibrations. A hardened steel mesh grille protects the BETA 52A

from the abuse and wear associated with touring.

FEATURES

Frequency response shaped speci cally for kick drums ﬁ

and bass instruments

Built in dynamic locking stand adapter with integral XLR –

connector simpli es setup, especially inside a kick drum ﬁ

Studio quality performance, even at extremely high sound

pressure levels

Supercardioid pattern for high gain before feedback and

superior rejection of unwanted noise

Hardened steel mesh grille that resists wear and abuse

Advanced pneumatic shock mount system that minimizes

transmission of mechanical noise and vibration

Neodymium magnet for high signal to noise ratio output – –

Low sensitivity to varying load impedance

Legendary Shure quality and reliability

•

APPLICATIONS AND PLACEMENT

The most common BETA 52A applications and placement tech-

niques are listed in the following table. Keep in mind that micro-

phone technique is largely a matter of personal taste there is no –

one correct microphone position.“ ”

Applic ation Suggested Microphone

Placem ent

Tone Quality

Kick Drum 5 to 7.5 cm (2 to 3 in.) away

from beater head, slightly

off-center from beater.

Sharp attack; maximum

bass sound, highest sound

pressure level.

20 to 30 cm (8 to 12 in.)

from beater head, on-axis

with beater.

Medium attack; balanced

sound.

20 to 30 cm (8 to 12 in.)

from beater head, 15 to 20

cm (6 to 8 in.) from edg e

of head.

Medium attack; thin, re-

duced bass sound.

5 to 7.5 cm (2 to 3 in.) away

from outside head, on-axis

with beater (double head

kickdrum o nly).

Softer attack; balanced,

resonant sound.

NOTE: To tighten the “ ”

beat, place a pillow or

blanket on bottom of drum

against beater head.

Electric

Bass Am pli-

fier

2.5 cm (1 in.) from speaker,

on-axis with center of

speaker cone.

Sharp attack; emphasized

bass.

2.5 cm (1 in.) from speaker,

at edge of speaker cone.

Sharp attack; higher fre-

quency sound.

10 to 15 cm (4 to 6 in.) from

speaker, on-axis with center

of speaker cone.

Sharp attack; full, balanced

sound.

60 to 90 cm (2 to 3 ft.) from

speaker, on-axis with center

of speaker cone.

Soft attack; mellow, higher

frequency sound.

MOUNTING THE BETA 52A ON A MICROPHONE STAND

The built in stand adapter features a dynamic locking system –

that permits adjustments to the microphone’s position, but resists

slipping when struck or bumped. To mount the BETA 52A on a

stand and adjust its position, proceed as follows:

Screw the integral stand adapter onto the end of a micro-

phone stand (see Figure 3). Adjust the stand height and

position as necessary.

Pivot the BETA 52A until it is in the desired position rela-

tive to the drum head or loudspeaker.

Lock the BETA 52A in place by rotating the adjustment

knob on the stand adapter clockwise until it is tight. Do

NOT overtighten the knob with tools.

If necessary, make minor adjustments to the microphone

position without loosening the adjustment knob.

Connect an audio cable to the integral XLR connector.

MODEL BETA 52®A

Produkt Specifikationer

Mærke:	Shure
Kategori:	Mikrofon
Model:	BETA 52A

Har du brug for hjælp?

Hvis du har brug for hjælp til Shure BETA 52A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Shure Manualer

28 September 2025

1 September 2025

22 August 2025

18 August 2025

22 Juli 2025

Shure PGA56-XLR Manual

15 Juli 2025

Shure ULXD6 Manual

23 Juni 2025

Shure MoveMic One Manual

21 Februar 2025

Shure MV7i Manual

21 Februar 2025

Shure VP89M Manual

29 December 2024

Mikrofon Manualer

Nyeste Mikrofon Manualer

SE Electronics V7 ENG Manual

15 December 2025

Eurosound PRO3 Manual

11 December 2025

Philips SmartMeeting PSE0540 Manual

8 December 2025

Galaxy Audio EVO-PE0P1 Manual

8 December 2025

Galaxy Audio EVO-PE0D4 Manual

8 December 2025

Philips SmartMeeting PSE0501 Manual

7 December 2025

Galaxy Audio AS-ANTM3 Manual

7 December 2025

Galaxy Audio EVO-PEED4 Manual

7 December 2025

TOA S4.10-RXA Manual

6 December 2025

Savage Mobile Vlogging Kit Manual

5 December 2025