Sloan HYB-7000 Manual

Sloan Toilet HYB-7000

Læs gratis den danske manual til Sloan HYB-7000 (2 sider) i kategorien Toilet. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Sloan HYB-7000, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTALLATION OF LAVATORY

1. PRIOR TO NEW INSTALLATION

NOTE: Adequate reinforced wall framing

is required behind the wall for proper

hanger bracket support. Use of wall anchors

or toggle bolts is not recommended. For

concrete walls a properly sized wall anchors

can be used.

• Determine appropriate wall location for the

lavatory. Consider that hot and cold water

supply lines with supply stops or a tempered

water supply line with supply stop and a drain

line will be required. A 120V electrical source

(receptacle) may also be required. Compare the

physical dimensions of the lavatory to the space

available for the installation.

2. UNPACK AND INSPECT LAVATORY

• Carefully remove sink from its protective carton

so as not to damage porcelain  nish. Check for

any damage to lavatory before proceeding with

the installation.

• Examine the carton for additional parts before

discarding packaging.

3. INSTALL DRAIN POP-UP AND FAUCET

• Install the faucet and drain assembly (not

included). Follow faucet manufacturers

instructions. Use plumbers putty on drain

assembly to ensure a water seal.

Wall-Hung Ledgeback Lavatory with Optional Shroud Installation

Model

The information contained in this document is subject to change

without notice.

SLOAN

10500 Seymour Avenue

Franklin Park, IL 60131

Phone: 1.800.9.VALVE.9 (982.5839) or 1.847.671.4300

Fax: 1.800.447.8329 or 1.847.671.4380

sloan.com

Code No. 0816132 Rev.3 (12/17)

All vitreous china dimensions shown in these drawings are nominal

and not to scale. Dimensions can vary within the tolerances

established in the governing ASME A112.19/CSA B45.1 standard. It

is important to consider this when planning rough-in and plumbing

layouts.

Wall Carrier rough-in information to be provided by wall carrier

manufacturer. Carrier and hardware not included with  xture

INSTALLATION OF OPTIONAL SHROUD (SOLD SEPARATELY)

NOTE: ONLY SCREWDRIVER-TYPE SUPPLY STOPS

ARE RECOMMENDED FOR USE WITH SHROUD TO

ACCOMMODATE LIMITED SPACE.

• Install drain and supply stops according to rough-in diagram

shown in drawing.

• Carefully open carton and remove ceramic shroud. Con rm

that no mounting hardware is missing.

• Mark shroud anchor holes as indicated and predrill holes.

TIP: If lavatory is already installed, before removing, hold

shroud in place and con rm vertical distance of shroud

mounting holes.

• Install 2 plastic shroud brackets with mounting screws,

washers and anchors as shown.

• Position shroud over drain, supply stops and shroud

brackets so that it nests inside matching lip on the

underside of lavatory.

• Insert a 2” wood screw and white cap assembly through

the shroud until it ‘ nds’ one of the holes on the grid of the

plastic shroud bracket. Tighten until secure and snap on

screw cap. Repeat for second side. Do not overtighten.

4.75”

(120 mm)

Shroud Plastic Bracket

Screw Cap

Finished Wall

CARE AND CLEANING OF VITREOUS CHINA

Clean lavatory with a cleaner safe for vitreous china.

Spray and wipe clean using soft cloth. Soft abrasive

cleaners may be used to remove stains.

LIMITED WARRANTY

Sloan Valve Company warrants its vitreous china

products to be made of  rst class materials, free from

defects of material or workmanship under normal use

and to perform the service for which they are intended

in a thoroughly reliable and ef cient manner when

properly installed and serviced, for a period of three

years from date of purchase. During this period, Sloan

Valve Company will, at its option, repair or replace any

part or parts which prove to be thus defective if

returned to Sloan Valve Company, at customer’s cost,

and this shall be the sole remedy available under this

warranty. No claims will be allowed for labor,

transportation or other incidental costs. This warranty

extends only to persons or organizations who

purchase Sloan Valve Company’s products directly

from Sloan Valve Company for purpose of resale.

THERE ARE NO WARRANTIES WHICH EXTEND

BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN

NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE

FOR ANY CONSEQUENTIAL DAMAGES OF ANY

MEASURE WHATSOEVER.

NOTE: IN NO EVENT SHALL THE SLOAN VALVE

COMPANY BE LIABLE FOR INCIDENTAL DAMAGES,

RESULTING FROM IMPROPER INSTALLATION, OR FOR

DAMAGES CAUSED BY NEGLECT, ABUSE OR

ALTERATION.

4. INSTALL MOUNTING HARDWARE

• Determine the desired height to the top

of lavatory sink rim.

• Mark a level line 3.75” (94mm) below

this height and mark the centerline.

• Mark and drill holes in wall for mounting

hanger bracket.

5. INSTALL LAVATORY

• Mount the lavatory on protruding lag bolts and

level. Mark anchor holes.

NOTE: If lavatory is not level or at wrong

height, remove and adjust lag bolts as needed.

• Install 2 – 2” (51mm) anchor bolts (not

supplied)

SS-3006 Shown with

Optional Shroud

WARNING: Any vitreous china can chip or

break if the bolts or nuts are over-tightened or if

mishandled.

BEFORE YOU START…

• Check all local plumbing and building codes.

• Check for any damage to the new lavatory sink

before installation.

WHAT YOU WILL NEED…

• Putty knife • 10” adjustable wrench

• Safety glasses • Phillips screwdriver

• Measuring tape • Flathead screwdriver

• Basin wrench • Drill

• Tube cutter • Plumbers putty

• Hacksaw • Silicone sealant

• Channel lock pliers

THE RIGHT CHOICE

We thank you for your purchase. Our products are

100% tested but should you have any questions,

please contact us by phone or at our web site listed

below.

4.50

[114.3]

34.00

[864]

4.19

[106]

4.75

[121]

3.00

[76]

2.75

[70]

3.25

[83]

5.00

[127]

8”

[203]

20”

[508]

3”

[75]

8”

[200]

3.375”

[83]

5.25”

[133]

5.25”

[133]

6X 1.375”

[32]

16.75”

[425]

4.75”

[120]

7.875”

[200]

7.20”

[183]

11”

[282]

18.25”

[463]

10.625”

[270]

4”

[101.6]

3”

[74]

2”

[50]

2X 2.375”

[59]

2X .375”

[10]

Reinforced wall framing

Holes for Hanger Bracket

ADA*

** Not ADA compliant when shroud is used

FINISHED FLOOR

DRAIN

SHROUD

ANCHORS

SUPPLIES

Produkt Specifikationer

Mærke:	Sloan
Kategori:	Toilet
Model:	HYB-7000

Har du brug for hjælp?

Hvis du har brug for hjælp til Sloan HYB-7000 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Toilet Sloan Manualer

16 Juni 2025

15 Juni 2025

15 Juni 2025

30 Marts 2025

Sloan HYB-7000 Manual

19 August 2024

Sloan HYB-1000-RET Manual

16 August 2024

Sloan WES-1000 Manual

16 August 2024

Sloan HYB-4000 Manual

15 August 2024

Sloan HYB-1000 Manual

15 August 2024

Sloan WES-4000 Manual

14 August 2024

Toilet Manualer

Nyeste Toilet Manualer

ProFlo PFTSEC1000WH Manual

15 December 2025

ProFlo PFTSHEC2000WH Manual

15 December 2025

ProFlo PF1815PTWH Manual

11 December 2025

ProFlo PFTSWE1001WH Manual

10 December 2025

Kohler K-8298 Manual

10 December 2025

ProFlo PFTSEC2000WH Manual

10 December 2025

ProFlo PFTSCOFA2000WH Manual

10 December 2025

Kohler K-3977 Manual

10 December 2025

ProFlo PF1912WH Manual

9 December 2025

ProFlo PF1705HE Manual

9 December 2025