Smartwares VD38W Manual

Smartwares Overvågningskamera VD38W

Læs gratis den danske manual til Smartwares VD38W (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Smartwares VD38W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

14 15 16 12

13 17 18 9 10

211

OPTIONAL:

TOWARDS THE

DOOR LOCK

3 4 5

12V 1Amp MAX

Always test the product on site before installation.

Be aware that different materials in between the Outdoor Intercom

and Indoor Monitor will affect the operating performance of the product.

Follow the Wiring and pairing guides to test the product.

Install the Outdoor Intercom in a dry location if possible.

Mount the Intercom at a suitable height and position to allow the

camera to see the visitor

Battery setup:

Outdoors intercom

1. On the back of the intercom, remove the 6 screws on the battery

compartment, and remove the cover

2. Insert the battery pack into the compartment, making sure it is positioned

correctly, with the marking "Rechargeable Li-Ion battery" facing you.

3. Replace the battery compartment cover and insert the 6 screws.

Indoor Monitor

1. On the back of the indoor monitor, open the battery compartment

cover pulling towards you.

2. Insert the battery pack into the compartment, making sure it is positioned

correctly, with the marking "Rechargeable Li-Ion battery" facing you.

3. Replace the compartment cover.

Installation and setup Outdoor intercom wall support

Key features

CAUTION

1. Please read these instructions before setting up and using the device.

2. Do not cut the power supply cable to extend it; the transformer will not operate with

a longer cable. Do not plug in the transformer until all the wiring has been finished.

3. This product is not a toy. Keep it out of reach of children.

4. Do not operate electrically powered products in explosive atmospheres, such as

in the presence of flammable liquids, gases, or dust. Electrically powered products

may create sparks which are likely to ignite dust or create fumes.

5. The warnings, precautions, and instructions presented in this instruction manual

cannot cover all possible conditions and situations that may occur the operator must

understand that common sense and caution are factors that the product can not

provide but the operator must put in place.

6. Do not expose the power adapter for this product to rain or moisture.

Water entering the Power Adapter will increase the risk of electric shock.

7. Do not abuse the Power Cord. Never use the cord for unplugging the plug from the outlet.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. The adapter must match the power outlet.

Never modify the cord in any way. Unmodified plugs and suitable outlets will reduce

risk of electric shock.

1. Antenne

2. Screen

3. UP button

4. LEFT button

5. RIGHT button

6. OK / Photo button

7. DOWN button

8. Intercom button

9. Door lock button

10. Monitor button

11. Microphone

12. LED lighting

13. USB port

14. Power ON/OFF

15. Metal support screws

16. Metal supports

17. Wall mount

18. Battery compartment cover

1. Rain cover

2. Microphone

3. Camera lens

4. Night vision lighting

5. Speaker

6. Name plate

7. Call button

8. Light sensor

9. Antenne

10. Battery compartment

11. Screw

12. Power and locking connector

Included in the pack:

Inside

Indoor Monitor Outdoors intercom

Outside

OPTIONAL

1. Select the location of the outdoor intercom, use the rain cover as a

template anD drill the holes to mount the plugs.

2. Mark and drill the hole in order to feed the electric cables through the wall.

3. Push the electric cables so that they are visible from the outside.

4. Glue the seal inside the rain cover.

5. Mount the rain cover with the mounting hardware included.

Pay attention to the mounting bracket on the lower support,

making sure the electric cables will fit through the joining

opening of the back plate in the lower corner.

6. Link the intercom electric cables as shown on the wiring diagram below.

7. Firstly, insert the upper part of the intercom into the rain cover and

place the lower part on the angled support.

8. Secure the intercom in place on the rain cover using the securing screws.

Name plate

1. If you need to fill the name plate, push strongly on the left side whilst

sliding the plate to the left in order to free the right side and then remove it.

2. Use a pointy object to remove the name plate from the inside of the

plate and fill-in your details.

3. Then, replace the label and follow the same steps in the opposite

order to reassemble the plate in the outdoor unit.

1. With a small screw driver, push the connexion bloc upwards on

the outdoor intercom in order to detach it.

2. Connect the DC power supply to the terminals marked + and -,

checking that the wires are linked correctly.

3. If required, connect the door lock cables to the 2 terminals, checking

the correct power supply to the door lock (only for an electric door lock,

max. 12 V, 1 A , through a separate power plug - NOT INCLUDED).

4. Replace the connector in the outdoor intercom, making sure the

polarity is correct.

Name plate Wiring

13-20mm

Produkt Specifikationer

Mærke:	Smartwares
Kategori:	Overvågningskamera
Model:	VD38W
Produktfarve:	Hvid
Kontroltype:	Knapper
Skærm diagonal:	3.5 "
Skærmteknologi:	TFT
Indbyggede højttaler(e):	Ja
Udgangsspænding for vekselstrømsadapter:	5 V
Højttalertelefon:	Ja
Maksimal udendørsinterval:	175 m
Indbygget mikrofon:	Ja
Farve:	Ja
Synsfelt vinkel (FOV):	45 °
Vekselstrømsadapterens udgangsstrøm:	1 A
Antal understøttede skærme:	1