Snap Circuits Basic Electricity SCP-10 Manual

Snap Circuits Legetøj Basic Electricity SCP-10

Læs gratis den danske manual til Snap Circuits Basic Electricity SCP-10 (5 sider) i kategorien Legetøj. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Snap Circuits Basic Electricity SCP-10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

If you have any problems, contact Elenco

(800) 533-2441 Fax: (847) 520-0085 e-mail: elenco@elenco.com Website: www.elenco.com or www.snapcircuits.net● ●

WARNING: SHOCK HAZARD -

Never connect Snap Circuits®

to the electrical outlets in your

home in any way!

WARNING: Always check your wiring before

turning on a circuit. Never leave a circuit

unattended while the batteries are installed.

Never connect additional batteries or any other

power sources to your circuits.

Basic Electricity

Model SCP-10

753159

Snap Circuits®uses electronic

blocks that snap onto a base

grid to build different circuits.

These blocks have different

colors and numbers on them so

that you can easily identify

them. Build the circuit shown by

placing all the parts with a black

1next to them on the clear base

grid first. Then, assemble parts

marked with a . Install three (3)2

“AA” batteries (not included)

into the battery holder (B3).

Set the meter (M5) to the 1A

setting.

Turn on the slide switch (S1).

The lamp (L4) comes on, and

the meter measures how much

electric current is flowing.

Project 1 Project 2 Lamp Current Batteries in Series

Electricity is the movement of sub-atomic charged

particles through a material due to electrical pressure

across the material, such as from a battery. Power

sources, like batteries, push electricity through a circuit,

like a pump pushes water through pipes. Wires carry

electricity, like pipes carry water. Devices like lamps use

the energy in electricity to do things. Switches control the

flow of electricity like valves and faucets control water.

The electrical pressure exerted by a battery or other

power source is called and is measured in voltage volts

(V). The “+” and “–” signs on a battery indicate which

direction it will “pump” electricity.

The is a measure of how fast electricityelectric current

is flowing in a wire, just as the water current describes

how fast water is flowing in a pipe. It is expressed in

amperes milliamps(A) or (mA = 1/1,000 of an ampere).

The “ ” of electricity is a measure of how fast energypower

is moving through a wire. It is a combination of the voltage

and current (Power = Voltage x Current). It is expressed in

watts (W).

The of a component or circuit represents howresistance

much it resists the electrical pressure (voltage) and limits the

flow of electric current. The relationship is Voltage = Current

x Resistance. When resistance increases, less current flows.

Resistance is measured in ( ).ohms W

If desired, use the voltage measured here (with 3 batteries) and the

current measured in project 1 to calculate the resistance and power of

the lamp:

Resistance equals Voltage divided by Current, and should be about 15

ohms. Power equals Voltage times Current, and should be about 1 Watt.

Your results may be different, because M5 is a simple meter with low

accuracy, and your battery voltage can vary.

Set the meter (M5) to the 5V setting, and turn on the slide

switch (S1). The lamp (L4) comes on, and the meter measures

the voltage from the 3 batteries.

Part B: Remove the left battery from the holder (B3), then snap

one side of the red jumper jumper on as shown, and touch

metal on the other end to the left spring in the battery holder.

Read the voltage on the meter, measuring 2 batteries, and

notice how the lamp is dimmer.

Part C: Now also remove the center battery from the holder and

touch metal on the end of the red jumper wire to the center

spring in the holder. Read the voltage on the meter, measuring

1 battery, and notice how the lamp is dimmer.

Placement

Level Numbers

Quiz answers:

1. B 2. B 3. C 4. A 5. B

Batteries are like electrical pressure, pushing electricity

through a circuit. Adding more batteries increases the

flow of electricity, making the lamp brighter.

Part B:

Part C:

Produkt Specifikationer

Mærke:	Snap Circuits
Kategori:	Legetøj
Model:	Basic Electricity SCP-10

Har du brug for hjælp?

Hvis du har brug for hjælp til Snap Circuits Basic Electricity SCP-10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Legetøj Snap Circuits Manualer

Snap Circuits Snaptricity SCBE-75 Manual

10 August 2024

Snap Circuits Beginner SCB-20 Manual

9 August 2024

Snap Circuits Pro SC-500 Manual

9 August 2024

Snap Circuits Arcade SCA-200 Manual

6 August 2024

Snap Circuits Basic Electricity SCP-10 Manual

6 August 2024

Legetøj Manualer

Nyeste Legetøj Manualer

Disney Princess SuperSeat 3-in-1 Manual

2 November 2025

Disney Finding Nemo SuperSeat 3-in-1 Manual

2 November 2025

SereneLife Infinity 3 SLKSLP5 Manual

19 Oktober 2025

Lego Disney Mickey and Friends 40456 Manual

17 Oktober 2025

Ikea MAJBAGGE 805.818.96 Manual

14 Oktober 2025

Lionelo Villy Manual

6 Oktober 2025

Vtech KidiGear Walkie Talkies Manual

5 Oktober 2025

Vtech Touch & Teach Turtle Manual

3 Oktober 2025

Silverlit Robo Street Kombat Manual

28 September 2025

Silverlit Program A Bot X Manual

27 September 2025