Speco Technologies SP6NXCTUL Manual

Speco Technologies Højttaler SP6NXCTUL

Læs gratis den danske manual til Speco Technologies SP6NXCTUL (1 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Speco Technologies SP6NXCTUL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Suspended Ceiling Installation

Remove the ceiling tile where the speaker is to be installed

Painting the Speaker Baffle

Cut along the smaller perforated line of the cutout

template, marked as paint shield. Push it into the front

baffle of the speaker. Paint the front. Remove the paint

shield after the paint has dried.

Loosen the four screws on the front baffle (counter

clockwise) 1/2 turn. Then tighten the screws(clockwise)

until the dog legs clamp the speaker to the ceiling.

Cut the hole in the tile. See step 1 of the Frame Construction

Ceiling Installation section on the back.

Apply 4 pieces of black putty (supplied),equally spaced 90°

apart, to the upper inside edge of the grille (see step 5 on

the back).

Install the speaker grille.

Connect the wires to the speak terminal clips (see step 2

on the back).

Application diagram

Packaging

Bring the speaker cable through the hole of the cut tile,

then reinstall the tile.

Remove the adjacent tile. Place 2 V-rails and 1 C-ring

across the tile where speaker is to be installed. Insert the

speaker through the bottom of the hole in the ceiling tile.

Do not over-tighten screws!

CAUTION

V-rails

C-ring

Connect a secondary support line from p1-he seismic tab

to a secure support point (see step 5 on the back).

PO WER

12V

3A MAX

OUTPUTS

4/8 Ohms

INPUTS

70V

REMO TE

(MONO)

(

)

10V

LISTED

1T23

I.T

.E.

OL/MUTE

CUS

Projector

DVD/VCR Combo

VGA w/

Audio Cable

Composite

Audio RCA

Variable

Volume/Mute Controller

Mini Power Amplifier

OLU

MUTE

User Guide

Two-way Ceiling

Speakers

V-rails

C-rings

Speakers

Speak Grilles

Frame Construction Ceiling Installation

Replace the top cover and tighten the screws.

Insert the speaker through the bottom of the hole in

the ceiling.

Loosen the four screws on the front baffle(counter

clockwise) 1/2 turn. Then tighten the screws (clockwise)

until the dog legs clamp the speaker to the ceiling.

Do not over tighten screws.

Connect a secondary support line from the seismic tab to a

secure support point. Set the rotary tap selector and install

the speaker grille.

Specifications:

CAUTION

Adjusting the Tap Selector

Seismic Tab &

Supprot Line

Ceiling Speaker

User Guide

Cut Material

Remove the top cover to access the speaker connector.

Attack the speaker wires to the 4-pole captive screw

connector. Insert the 4-pole captive

screw plug into the connector on back of the speaker.

Install the conduit and secure the connections.

68-1065-01 Re v. B

06 06

Acoustic & Electrical

General

Speaker type

..................................

2-w ay, ceiling speaker with metal back can

Frequency range

...........................

65 Hz to 20 kHz,

Power handling

..............................

60 Watts RMS

Nominal sensitivity......................

88 dB, 1W@1m

Nominal coverage angle

..............

110° conical coverage

Nominal impedance ....................

8 ohms

Transformer taps

....................

70V:: 30W, 15W, 7.5W, 3.8W, 1.9W, 8 ohms

100: null, 30W, 15W, 7.5W, 3.8W, 8 ohms

Woofer ...........................................

6.5" (165 mm) polypropylene cone

with moisture resistant coating

Tweeter..........................................

3/4" (19 mm) silk dome

Overload protection.......................

Full range power limiter with the 8 ohm direct

input only, protecting the tweeter, woofer, and

crossover.

Temperature/humidity .................

Storage:

-40 to +158 °F (-40 to +70 °C) /

10% to 90%, noncondensing

Operating: +32 to +122 °F (0 to +50 °C) /

10% to 90%, noncondensing

Listings ........................................

UL1480

Compliances ................................

Warranty .......................................

1 years parts and labor

NOTE: All nominal level are at ±10%.

NOTE: Specifications are subject to change without notice.

Parallel Hookup Wiring Diagram

Apply 4 pieces of black putty

(supplied),equally spaced 90°

apart, to the upper inside

edge of the grille.

Conduit

Enlarged to

Show Detail

Cover

4-pole Captive

Screw Connector

From

Power

Amplifier

Trace template.

To Speaker

THRU

7.5

●

1.9

3.8

70V

7.5

100V

3.8

Take the cutout template from the packaging box and

punch out along the larger perforated circle. Place

the cutout template against the bottom of the ceiling and

trace the inside of it. Carefully cut out the ceiling material

along the circle.

120 Watts PEAK

SP6NXCTUL

Power Amplifier

Speaker 1 Speaker 2 Speaker 3

To Speakers

Ceiling Speaker

SP6NXCTUL

Produkt Specifikationer

Mærke:	Speco Technologies
Kategori:	Højttaler
Model:	SP6NXCTUL
Dybde:	196.85 mm
Produktfarve:	Black, White
Udgangseffekt (RMS):	120 W
Husmateriale:	Metal
Anbefalet brug:	Universel
Frekvensområde:	60 - 20000 Hz
Impedens:	8 ohm (Ω)
Forbindelsesteknologi:	Ledningsført
Lyd-output kanaler:	2.0 kanaler
Højttaler, placering:	I væggen/i loftet
Diameter:	260.35 mm
Antal drivere:	1
Diskanthøjttaler:	Ja
Sensitivitet:	87 dB
Magnet-type:	Ferrit
Diskant diameter:	0.75 "
Bashøjttaler:	Ja
Forstærker:	Indbygget
Woofer diameter (britisk mål):	6.5 "
Egnet til udendørs brug:	Ja
Antal Euroblock input stikforbindelser:	1