StarTech.com ET1000SM40LC Manual

StarTech.com Ikke kategoriseret ET1000SM40LC

Læs gratis den danske manual til StarTech.com ET1000SM40LC (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11 anmeldelser. Har du et spørgsmål om StarTech.com ET1000SM40LC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1 x ET1000SM40LC media converter•

1 x Power Adapter•

1 x Installation Guide•

1000Base network infrastructure•

Single Mode ﬁber cable•

Connect the ﬁber network cable to the LC connector on 1.

the ﬁber media converter. Using UTP Ethernet cable,

connect the cable to the RJ45 jack.

Set the Auto/Force switch on the media converter, to 2.

turn auto negotiate on or off. If set to Force, set the

Duplex switch (full/half) according to the speciﬁcations

of your networking equipment.

The following example illustrates the connection 3.

scheme when connecting from a 1000Base-TX port of

a hub/switch to a 1000Base-SX/LX port of another hub/

switch, through the ﬁber media converter:

The following example illustrates the connection 4.

scheme when connecting from a 1000Base-TX port on

a hub/switch to a 1000BASE-TX Network Interface Card

(NIC) in a computer through the ﬁber media converter:

Full/ Half:

The Fiber and UTP Duplex will be conﬁgured in Full

duplex or Half duplex.

This switch includes an “Auto Reset” function so the *

power-reset is not necessary when any modiﬁcation is

made here.

LBT:

Loop-back test and get remote side status :

(OFF = Not Active, ON = Active).

If the local side loop-back test is active, then LEDs *

(except PWR) will all blink rapidly and refresh to display

the remote side status.

LLF:

Link Loss Forwarding (OFF = Not active, On = Active)

Auto/Force:

Auto negotiate duplex mode, or force Full/Half via DIP

switches.

LED Name Status Description

PWR Power

ON Unit is powered

OFF Unit is not powered

Blink LBT mode enabled

Full Duplex Mode ON Fiber side Full Duplex Mode

OFF Half Duplex Mode

FX Fiber Link

ON Fiber link is detected

OFF Fiber link is not detected

Blink Fiber activity

LBT

Loop-back

Test/Get CPE

status

Blink Mode enabled

OFF Mode disabled

LLF Link Loss

Forwarding

ON Mode enabled

OFF Mode disabled

TX Ethernet Link

ON UTP link is detected

OFF UTP link is not detected

Blink UTP activity

Warranty Information

This product is backed by a one year warranty.

In addition, StarTech.com warrants its products against defects in materials

and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with

equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising

from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ofﬁcers, directors, employees or agents) for any damages (whether direct

or indirect, special, punitive, incidental, consequential, or otherwise), loss of proﬁts, loss of business, or any pecuniary loss, arising out of or related to the use of

the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws

apply, the limitations or exclusions contained in this statement may not apply to you.

Connectors

1 x RJ45 Ethernet

1 x LC Fiber

1x DC power connector

Fiber Type Single Mode

Maximum Distance 40 km

Duplex Modes Full/Half duplex Ethernet modes

Protocol Standards IEEE802.3 1000Base-TX,

IEEE802.3z 1000Base-SX/LX

Power Adapter 12VDC, 1A, center positive

Operating Temperature 0 - 50o C

Humidity 10-90% (non-condensing)

Dimensions 122.0 mm x 85.0 mm x 20.0 mm

Weight 340 g

This ﬁber media converter incorporates a Fiber Loop-

back Testing feature which allows the system to conﬁrm

whether or not the ﬁber or Ethernet circuit loop is

complete. The local-side unit will send out a detect

message which includes both command and test-pattern

data to the remote-side unit and request for an answer.

When the remote-side unit receives the message, it will

attempt to recognize the command.

After the remote-side unit recognizes the command

message, it will deliver the received test-pattern data

back to the local-side unit, completing the circuit loop, and

enabling the rack mount unit to easily monitor the remote

side unit(s). The remote side status message includes

the ﬁber-side link and duplex status, the UTP-side link,

duplex, speed, power, transmission and ﬁber failure

status.

Please note that while Loop-back testing is in process,

the ﬁber side transmission will be halted. If the local-side

cannot access the remote-side while in Loop-back Testing

mode, only the power LED will ﬂash (rapidly):

This ﬁber media converter incorporates a Fiber Link

Forwarding feature that allows indirect sensing of a

Fiber Link Loss via the 1000 Base-TX UTP connection.

Whenever the media device detects a Link Loss on

the Receive ﬁber (Fiber Link OFF), it disables its UTP

transmitter so that a Link Loss condition will be sensed

on the receive UTP port (as depicted in the following

diagram). The Link Loss can then be easily monitored and

reported at the remote UTP port’s host equipment.

This feature has no effect on the media converter’s

UTP Link LED, which continues to function normally,

independent of the state of the Fiber Link LED and the

UTP transmitter. This feature is enabled by default.

DIP Switches RJ45 port Fiber port

LED

Indicators

Produkt Specifikationer

Mærke:	StarTech.com
Kategori:	Ikke kategoriseret
Model:	ET1000SM40LC
Vægt:	690 g
Pakkevægt:	670 g
Dimensioner (BxDxH):	400 x 490 x 260 mm
Forbindelsesteknologi:	Ledningsført
Fuld duplex:	Ja
I/O-porte:	2x Fiber Optic LC F\n1x RJ45 F