StarTech.com ET90110SM30 Manual

StarTech.com Ikke kategoriseret ET90110SM30

Læs gratis den danske manual til StarTech.com ET90110SM30 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 22 anmeldelser. Har du et spørgsmål om StarTech.com ET90110SM30, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Introduction

Thank you for purchasing a StarTech.com Single-Mode Media

Converter. This product offers a cost-effective method of bridging

two Ethernet networks using single-mode fiber optic cable, at dis-

tances up to 30km (~19 miles).

Features

• Simple installation and use

• Supports full or half-duplex operating modes

• Supports loop-back testing

Before You Begin

System Requirements

• Fiber Cable

• 10Base-T; Cat 3, 4 or 5 or 100Base-Tx, Cat 5 or 6 cable

• Power source

Contents (per unit)

• Media Converter (1)

• 12V DC Power Adapter (1)

• Instruction manual (1)

Basic Setup

1. Connect the fiber interface cable to the Unit. Using UTP cable,

connect the ethernet connection to the RJ45 jack.

2. Set the switch (full/half) according to the specifications of Duplex

your equipment.

Media Converter Connections

The following example illustrates the connection scheme when

connecting from a 10Base-T/100Base-TX port of one hub to a

100Base-FX port of another hub, through the fiber converter:

The following example illustrates the connection scheme when con-

necting from a 10Base-T/100Base-TX port of one hub to a 10Base-

T/100BASE-TX Network Interface Card (NIC) in a computer through

the fiber converter:

Front Panel DIP Switch Settings

1. Full/ Half:

The Fiber and UTP Duplex will be configured in Full-duplex or Half-

duplex. *This switch includes an “Auto Reset” function so the

power-reset is not necessary when any modification is made

here.

2. NORM / LBT - Loop-back test :

(NORM = Not Active, LBT ON = Active) If the local sidePlease note:

loop-back test is active, then LEDs (except PWR) will all blink

rapidly and refresh to display the remote side status.

10/100 Single Mode Media Converter (SC – 30km)

ET90110SM30 LED Function State Status

PWR Power Indicator

Off

Blinking

Converter has power

Converter has no power

LB testing & Get CPE status function enabled

Fiber

Full Mode display On

Off

Fiber side Full Duplex mode

Half-duplex mode

Link Fiber link

Off

Blinking

The fiber link is ok

No link, or the link is faulty

Receiving data on the fiber

100 Link Speed On

Off

100Mbps Link Speed

10Mbps Link Speed

Full Mode display On

Off

Ethernet side Full Duplex mode

Half Duplex mode

LAN

Link Ethernet Link

Off

Blinking

The UTP link is ok

No link, or the link is faulty

Receiving data on Ethernet

LED Indicators

The following diagram and chart outline the meaning of each LED

located on the media converter(s):

Fiber Connection

Fiber Cable

100BASE-TX

UTP Connection

RJ-45 to HUB

connection

Fiber Transceiver

connection

Fiber Cable

100BASE-TX

UTP Connection

FULL

LBT ON

HALF

Fiber Full

PWR

100

Full

Link

LAN Link

Cont’d on reverse

NORM

Produkt Specifikationer

Mærke:	StarTech.com
Kategori:	Ikke kategoriseret
Model:	ET90110SM30
Vægt:	340 g
Pakkevægt:	920 g
Dimensioner (BxDxH):	20 x 122 x 85.6 mm
Forbindelsesteknologi:	Ledningsført
Maksimal dataoverførselshastighed:	100 Mbit/s
Fuld duplex:	Ja
I/O-porte:	1 - RJ45\n2 - SC