StarTech.com ET90110WDM Manual

StarTech.com Ikke kategoriseret ET90110WDM

Læs gratis den danske manual til StarTech.com ET90110WDM (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om StarTech.com ET90110WDM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Introduction

Thank you for purchasing a StarTech.com Single-Mode WDM Media

Converter. This product allows you to bridge two Ethernet networks

using fiber cable, and offers Wave Division Multiplexing, which allows

the use of a single fiber cable for both sending and receiving data

(Tx/Rx), reducing the amount of cable required.

Features

• Simple installation and use

• WDM (Wave Division Multiplexing) allows the use

of a single fiber cable for both sending and

receiving data

• LED indicators display single-mode, multi-mode

and power status of the converter

• Supports link-loss-forwarding function, loop-back test, remote

monitor status

Before You Begin

System Requirements

• Fiber Cable

• 10Base-T; Cat 3, 4 or 5

100Base-Tx, Cat 5 or 6 cable

• Power source

Contents (per unit)

• Media Converter (1)

• 12V Power Adapter (1)

• Instruction manual (1)

Basic Setup

1. Connect the fiber interface cable to the A-Unit. Using UTP cable,

connect the ethernet connection to the RJ45 jack.

2. Set the Fx switch (marked according to the specifications FIBER

of your fiber side equipment. The switch has two positions, HALF

(Half Duplex) and (FullDuplex). A Full Duplex setting will be FULL

indicated by anLED (see LED Indicators).

Media Converter Connections

The following example illustrates the connection scheme when con-

necting from a 10/100Base-TX port of one hub to a 100Base-FX port

of another hub, through the fiber converter:

The following example illustrates the connection scheme when con-

necting from a 10/100Base-TX port of one hub to a 100BASE-TX

Network Interface Card (NIC) in a computer through the fiber

converter:

Front Panel DIP Switch Settings

1. Full/ Half:

The Fiber Duplex will be configured in Full-duplex or Half-duplex

2. Loop-back test and get remote side status :

(NORM = Not Active, LBT ON = Active)

Please note: If the local side loop-back test is active, then LEDs

(except PWR) will all blink rapidly and refresh to display the remote

side status.

10/100 Mbps Single Mode WDM Media Converter

ET90110WDM (ET90110WDMA + ET90110WDMB)

Revised:7 June 2006 (A)

Support, Warranty Information, and Regulatory Compliance Statement

If you ever need help with your product, visit www.startech.com/support and access our com-

prehensive selection of online tools, documentation, and downloads. This product is backed by a

one-year warranty. In addition, StarTech.com warrants its products against defects in materials

and workmanship for the periods noted, following the initial date of purchase. During this period,

the products may be returned for repair, or replacement with equivalent products at our discre-

tion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products

from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability: In no event shall the liability of StarTech.com Ltd. and StarTech.com USA

LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect,

special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any

pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for

the product. Some states do not allow the exclusion or limitation of incidental or consequential

damages. If such laws apply, the limitations or exclusions contained in this statement may not

apply to you.

FCC Compliance Statement: This equipment has been tested and found to comply with the lim-

its for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected.

• Consult the dealer or an experienced radio/TV technician for help.

Use RJ-45 jack to HUB

connection

Fiber Cable

10/100BASE-TX

UTP Connection

Fiber

Transceiver

connection

PWR

Fiber Full

Fiber Link

LAN 100

LAN Full

LAN Link

LED Function State Status

PWR Power Indicator

Off

Converter has power

Converter has no power

Fiber Full Mode display

Off

Fiber side full duplex mode (200mbps)

Fiber side half-duplex mode

Fiber Link Fiber link

Off

Blinking

The fiber link is okay

No link, or the link is faulty

Receiving data on the fiber

LAN 100 Mode display

Off

UTP side is operating in 100Mbps mode

UTP side is operating in 10Mbps mode

LAN Full Mode display

Off

UTP side full duplex mode (200mbps)

UTP side half-duplex mode

LAN Link Ethernet Link

Off

Blinking

The UTP link is ok

No link, or the link is faulty

Receiving data on Ethernet

LED Indicators

The following diagram and chart outline the meaning of each LED

located on the media converter(s):

NORM

FULL

FIBER

LBT ON

HALF

Wavelength Tx: 1310 nm / Rx: 1550 nm

BER

<10

-10

Sensitivity -32dBm

Outpout Power -18 dBm (A), -15dBm (B)

Power Margin 14 dB (A), 17dB (B)

Return Loss -14dBm

Supported Cable Type 9/125µm Single Mode (SC Connector)

Ethernet Network Interface 10/100 Mbits/sec. (via auto-negotiation)

Switching Mechanism Store and Forward

Additional Features

Link-loss forwarding, loop-back test, remote

monitor status

Network Standards

Compliance

IEEE 802.3 10Base-T,

802.3u100Base-TX, 100Base-FX

MTBF 38000 hours (minimum)

Cable Length 20 KM (max) using single mode fiber optic cable

Product Dimensions (LxWxH)

122mm x 85mm x 20mm (4.8 x 3.3 x 0.9 in.)

Product Weight 0.65 lb (295 g)

Data Transfer Rate (max.) 100 Mbits/sec (Full and Half duplex supported)

Certifications (regulatory etc.) FCC, CE (Class A)

Power Adapter DC 12V, 1A, Center Pos.

General Specifications

Produkt Specifikationer

Mærke:	StarTech.com
Kategori:	Ikke kategoriseret
Model:	ET90110WDM
Vægt:	950 g
Pakkevægt:	1100 g
Dimensioner (BxDxH):	400 x 490 x 260 mm
Effektkrav:	12VDC, 1A
Grænseflade:	Ethernet
Maksimal dataoverførselshastighed:	100 Mbit/s
Bølgelængde:	1310 nm
Stik:	1 - Fiber Optic SC & 1 - RJ-45
Overholdelse af branchestandarder:	IEEE 802.3 10Base-T, 802.3u 100Base-TX, 100Base-FX