StarTech.com ET90110WDM2 Manual

StarTech.com Ikke kategoriseret ET90110WDM2

Læs gratis den danske manual til StarTech.com ET90110WDM2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 6 anmeldelser. Har du et spørgsmål om StarTech.com ET90110WDM2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Instruction Manual

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

I T: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

P T: Guia do usuário - pt.startech.com

Manual Revision: 06/17/2016

For the most up-to-date information, please visit: www.startech.com

Packaging Contents

• Fiber Media Converter (2 x for ET90110WDM2)

• Universal Power Adapter (2 x for ET90110WDM2)

• Power Adapter Plugs (2 Sets of NA/EU/UK/AU for

ET90110WDM2)

• Grounding Screw

• Instruction Manual

ET90110WDM2 / ET90110SM302

10/100 Mbps Ethernet to Single Mode SC WDM Fiber Media Converter Kit - 20km/30km

System Requirements

• 10BASE-T or 100Base-TX compatible Ethernet network equipment

• RJ45 terminated UTP Cat5 or better Ethernet cable

• 100BASE-FX compatible ber optic network equipment

• SC terminated single mode 9/125 micron (μm) ber optic cable

• Available AC electrical outlet

Installation

1. Make sure the DIP switches are set appropriately for your network

conguration (see “DIP Switch Settings“ section for details).

2. Setup the media converters at each of their respective end

point locations.

3. Connect the ber optic network cable from one media

converter to the other media converter.

4. Connect a UTP Ethernet cable, from a computer/switch to the

RJ45 jack on the media converters at each end point.

5. Connect the included power adapters to the media converters.

6. The following example illustrates the connection scheme

when connecting from a 100BASE-TX Ethernet port on a

hub/switch to a 100BASE-TX Ethernet Network Interface

Card (NIC) in a computer through the ber media converter:

DC Power connector

Ground Point (optional)

Rear View

ET90110WDM2 - Front View

RJ45 Ethernet

connector

SC ber

connector

DIP Switches

LED indicators Card Release

Thumbscrew

RJ45 Ethernet

connector

SC Duplex ber

connector

DIP Switches

LED indicators Card Release

Thumbscrew

ET90110SM302 - Front View

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they

occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual

applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks,

registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and

access our comprehensive selection of online tools, documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two year warranty.

In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be

returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages

arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,

consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not

allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

LED Status

LED Name Status Description

PWR Power

ON Unit is powered

OFF Unit is not powered

FEF Far End Fault

ON Link Fault on far end device

OFF No Link Faults

LNK

(FX)

Fiber Link

ON Fiber link is detected