StarTech.com I51G-ETHERNET-SWITCH Manual

StarTech.com Ikke kategoriseret I51G-ETHERNET-SWITCH

Læs gratis den danske manual til StarTech.com I51G-ETHERNET-SWITCH (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 53 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 27 anmeldelser. Har du et spørgsmål om StarTech.com I51G-ETHERNET-SWITCH, eller vil du spørge andre brugere om produktet?

Side 1/2
For additional self-service support options and community forums, please visit: www.StarTech.com/support
Revision: October 3, 2024
Quick-Start Guide
Product ID
I51G-ETHERNET-SWITCH
Feature Function
1
Connector
Connect the Gigabit Ethernet Industrial Unmanaged
Switch DC Power Sourceto a
Requires an input voltage of 9-60V DC
A t is availableGrounding Poin
2DIP Switches
or the (BSP) Enable Disable Broadcast Storm Protection
and (QoS) featuresQuality of Service
3Power LED
Indicates if the unit is receiving power
Solid Green: Power
O: No Power
4
RJ45 Ethernet
Ports
Connects the unit and to the Network Devices Local
Network Ethernet Cablesvia
Supports 10/100/1000Mbps
5
Link/Activity LED
Indicators
Solid Green: Active link
Flashing Green: Activity
6
Mounting Holes
(Not Shown)
Located at the back of the unit
Use to attach the or the Mounting Ear Kit DIN Rail Bracket
5-Port Gigabit Ethernet Industrial Unmanaged Switch - DIN Rail Mountable
Package Contents
Gigabit Switch x 1
3-Pin Terminal Block x 1
DIN Rail Mounting Kit x 1
Mounting Ear Kit x 1
Quick-Start Guide x 1
Requirements
For the latest manuals, product information, technical specications, and declarations of
conformance, please visit: www.StarTech.com/I51G-ETHERNET-SWITCH
Phillips head screwdriver
Terminal block DC power supply: 9-60V DC
Installation
DIP Switches
DIP Switch ON OFF
1 - BSP
Broadcast Storm Protection (BSP) limits the rate of
broadcast trac after a 2,000 packet per second
threshold is exceeded, additional packets outside of
this threshold are dropped
Disables BSP
(Default)
2 - QoS
Quality of Service (QoS) prioritizes tagged trac
(IEEE 802.1Q) to ensure that important data is
transmitted eciently with minimal delay, even
during periods of high network congestion
Disables QoS
(Default)
1. Adjust the according to the needs of the setup.DIP Switches
Note: A power cycle is required after changing the DIP Switch settings for the changes to
take eect.
2. Connect a to the . Recommended power DC Power Source Terminal Block Connector
9-60V DC.
Warning!
Verify the correct polarity before supplying power to prevent equipment damage.
Ensure that the unit is properly grounded to ensure safe operation.
3. Plug in an between (Uplink) and the .Ethernet Cable Port 5 Local Network
4. Connect as needed to the remaining using Network Devices RJ45 Ethernet ports
Ethernet Cables.
*Product may vary from image
1
6
4
5
2
3


Produkt Specifikationer

Mærke: StarTech.com
Kategori: Ikke kategoriseret
Model: I51G-ETHERNET-SWITCH

Har du brug for hjælp?

Hvis du har brug for hjælp til StarTech.com I51G-ETHERNET-SWITCH stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret StarTech.com Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JET

JET JAT-450 Manual

4 December 2025
JET

JET JCT-3643 Manual

4 December 2025
Draper

Draper 34570 Manual

4 December 2025
Advantech

Advantech ADAM-4051 Manual

4 December 2025
SPT

SPT SU-1054 Manual

4 December 2025
ELO

ELO E119034 Manual

4 December 2025
ELO

ELO E432771 Manual

4 December 2025