StarTech.com IMC1GSFP30W Manual

StarTech.com Ikke kategoriseret IMC1GSFP30W

Læs gratis den danske manual til StarTech.com IMC1GSFP30W (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8 anmeldelser. Har du et spørgsmål om StarTech.com IMC1GSFP30W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: April 26, 2023

Product Diagram (IMC1GSFP30W)

Component Function

1DIP Switches

DIP Switch Position Function

DIP 1 (Left Side)

100 Mbps

installations

Down

1000 Mbps

installations

DIP 2 (Right Side)

Link Fault

Pass Through

enabled

Down

Link Fault

Pass Through

disabled

(default

setting)

Power Input

Port

• Connect a Power Source

• DC power range is from 48V to 56V

Note: Ensure the input voltage is always within this range.

Industrial RJ45 to Open SFP Mini PoE Media Converter - 1000 Mbps (1G) - 30W

LED

Indicators

LED Type Status Indication

PWR

On Power detected

O Power not detected

LK/Act

On SFP detected

Flashing

Fiber data is transmitting

and receiving

4RJ45 Port

• Connect a UTP/STP Cat 5e (or higher) Network Cable

LED

Type

Status Indication

LNK

On Network connection is detected

Flashing

Network data is transmitting and

receiving

POE

Power Source Equipment (PSE) is

activated and is Powered Device (PD)

detected

Flashing not detectedPD

5SFP Slot • Insert a 100/1000Base-X SFP Transceiver Module

Requirements

For the latest requirements, please visit .www.startech.com/IMC1GSFP30W

• Network Equipment (e.g. Router, Network Switch) x 1

• MSA-Compliant 100/1000Base-X SFP Transceiver Module x 1

• RJ45 Terminated UTP/STP Cat 5e (or better) Network Cable x 1

• Terminated Fiber Optic Cable (dependent on the chosen SFP Module) x 1

• Industrial DC Power Supply Unit or Universal Power Adapter with Type N

(OD: 5.5 mm, ID: 2.5 mm) Barrel Connector x 1

• Flat Head Screwdriver x 1

• (Optional - for mounting) Phillips Head Screwdriver x 1

• (Optional - for mounting) Screws x 2

Installation

Connecting the Media Converter

1. Insert an (sold separately) into the MSA-Compliant SFP Transceiver Module SFP

Slot Media Converter.on the

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (A)/NMB-3(A)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two

conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

This product is backed by a two-year warranty.

For further information on product warranty terms and conditions, please refer to .www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or

agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots,

loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the

product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the

limitations or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT: startech.com/it

JP: startech.com/jp

StarTech.com Ltd.

45 Artisans Crescent

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Road

Brackmills,

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

4490 South Hamilton

Road

Groveport, Ohio

43125

U.S.A.

StarTech.com Ltd.

Siriusdreef 17-27

2132 WT Hoofddorp

The Netherlands

Power Adapter Terminal Block to Barrel Power Connector Adapter to the .

Mounting the Media Converter

Wall Mounting

1. Align the holes in the with the holes in the back of the Wall Mount Brackets Media

Converter.

2. Insert two through the and into the Phillips Head Screws Wall Mount Brackets

Media Converter.

3. Tighten the using a (sold Phillips Head Screws Phillips Head Screwdriver

separately).

Note: Be careful not to over-tighten the .Screws

4. Insert two (sold separately) through the and into the Screws Wall Mount Brackets

Mounting Surface.

5. Tighten the using the appropriate .Screws Screwdriver

DIN Rail Mounting

1. Align the holes in the with the holes in the back of the DIN Rail Bracket Media

Converter.

2. Insert three through the and into the Phillips Head Screws DIN Rail Bracket Media

Converter.

3. Tighten the using a .Phillips Head Screws Phillips Head Screwdriver

Note: Be careful not to over-tighten the .Screws

4. Hang the top of the (the section with the two metal clips) onto a DIN Rail Bracket

Top Hat DIN Rail style .

5. Press the down and forward to lock the bottom section onto the DIN Rail Bracket

DIN Rail.

2. Remove the from the .Dust Cover SFP Module

3. Connect a (sold separately) to the on the Fiber Optic Cable Fiber Optic Port SFP

Module Fiber-Network Device and to the .

4. Connect a (sold separately) to the on the Network Cable RJ45 Port Media

Converter Network Equipment. and to the

Powering the Media Converter

Connecting and installing the 3-pin Terminal Block must be completed by a licensed

Electrician.

Notes: Make sure that you turn o the power source before connecting the power wire

to the Terminal Block.

Do Not exceed the recommend power source voltage as it may result in personal or

product damage.

Connect the (not included) to the . Industrial DC Power Supply Unit Terminal Block

• Connect the to Positive Wire V+

• Connect the to Negative Wire V-

• Connect the to Neutral Wire Ground

• Secure the by tightening the in the with a Wires Screws Terminal Block Flat Head

Screwdriver

--or--

Connect a from a Type N (OD: 5.5 mm, ID: 2.5 mm) Barrel Connector Universal

Produkt Specifikationer

Mærke:	StarTech.com
Kategori:	Ikke kategoriseret
Model:	IMC1GSFP30W
Kode for international beskyttelse (IP):	IP30
Bredde:	36 mm
Dybde:	59 mm
Højde:	49 mm
Vægt:	80 g
Produktfarve:	Sort
Pakkevægt:	204.9 g
Pakkedybde:	105 mm
Pakkebredde:	155 mm
Pakkehøjde:	64 mm
Opbevaringstemperatur (T-T):	-40 - 85 °C
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	-40 - 75 °C
Husmateriale:	Aluminium
Hurtig installationsvejledning:	Ja
Forbindelsesteknologi:	Ledningsført
Certificering:	CE, FCC
Netværksstandarder:	IEEE 802.3, IEEE 802.3u, IEEE 802.3z
Harmoniseret systemkode (HS):	85176990
Bæredygtighedscertifikater:	RoHS
Indgangsspænding:	48 - 56 V
Hovedkassen højde (udvendigt):	225 mm
Hovedkassens længde (udvendigt):	345 mm
Hovedkassens bredde (udvendigt):	355 mm
Intern:	Ingen
Maksimal dataoverførselshastighed:	1000 Mbit/s
Fiber optisk strømstik:	SFP
Maksimal overførselsafstand:	100 m
Bølgelængde:	- nm
Produkter pr. hovedkasse (udvendigt):	20 stk
Strøm over Ethernet (PoE):	Ja
Gennemsnitstid mellem fejl (MTBF):	500000 t
Strømstiktype:	Type N
Total Power over Ethernet (PoE):	30 W
Flowkontrol support:	Ja
Jumbo Frames support:	Ja
Jumbo rammer:	16000
Bufferstørrelse:	512 KB
DIN-skinne montering:	Ja
Fiberkanal porte:	1
Fibertilstandsstruktur:	Multi-mode, Single-mode
Duplex system:	Fuld