StarTech.com M2E1BRU31C Manual

StarTech.com Ekstern harddisk M2E1BRU31C

Læs gratis den danske manual til StarTech.com M2E1BRU31C (2 sider) i kategorien Ekstern harddisk. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 17 anmeldelser. Har du et spørgsmål om StarTech.com M2E1BRU31C, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: December 18, 2019 6:37 PM

Product Diagram (M2E1BRU31C)

Exterior

Component Function

1 Power LED

• Solid: Indicates that the Enclosure is receiving

power.

• Flashing: Indicates that the Drive activity.

2 USB-C Port

• Used to connect the Enclosure to the Host

Computer.

Interior

Component Function

3 Drive-Bay Screws x 4

• Used to secure the Drive Bay Cover in the

Enclosure.

4 Drive Connector • Used to connect the Drive to the Enclosure.

USB 3.2 Gen 2 Type C IP67 Rugged NVMe Enclosure

Adjustable Drive

Length Holes

• Used to accommodate dierent drive lengths.

Drive-Mount Screw/

Nut

• Used to secure the Drive to the Enclosure.

Requirements

For the latest requirements and full manual, please visit www.startech.com/

M2E1BRU31C

Installation

Warning! Drives should be handled carefully, especially when they’re transported. If

you’re not careful with your drives, you may lose data as a result.

Installing an 80 mm Drive

1. Using the Torx Screwdriver (included), remove the Drive-Cover Screws (x 4) from

the bottom of the Enclosure and remove the Cover Plate.

2. Place the Drive next to the Drive Tray and align the screw groove on the Drive with

the Adjustable Drive Length Holes on the Drive Tray.

3. Use the Torx Screwdriver and to remove the Drive-Mount Screw from the

Enclosure.

4. Gently slide the connector on the Drive (on a 30-degree angle) into the Drive

Connector on the Enclosure.

Note: The connector on your drive is keyed so that it only ts one way.

5. Lightly push the Drive down into position on the circuit board.

6. Insert the Drive-Mount Screw through the screw groove on the Drive and into the

Drive-Mount Screw Hole on the Enclosure.

7. Using the Torx Screwdriver tighten the Drive-Mount Screw, being careful not to

over-tighten.

8. Place the Cover Plate back onto the bottom on the Enclosure. Make sure that the

Cover Plate is properly aligned with the top of the Enculosure creating a tight seal

and that nothing is obstructing the Cover Plate, in order to provide a water and

dust resistance seal.

9. Insert the Drive-Cover Screws back into the four corner on the bottom of the

Enclosure.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a two-year warranty.

For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: fr.startech.com

DE: de.startech.com

ES: es.startech.com

NL: nl.startech.com

IT: it.startech.com

JP: jp.startech.com

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

9. Use the Torx Screwdriver to tighten the Drive-Tray Screws.

10. Remove the backing from the Adhesive Strips and position them overtop of

the Drive-Cover Screws (two secrews per Adhesive Strip) on the bottom of the

Enclosure, sealing the Drive-Cover Screws.

Connecting a Drive to a Computer

When the Enclosure is connected to the Host Computer the OS will automatically

install the necessary software.

Note: The Enclosure does not require an external power supply, as it receives enough

power through the USB port that it is connected to. However, not all USB ports may be

able to provide enough power to power the Enclosure.

• Connect a USB-C Cable to the USB-C Port on the Enclosure and to a USB port on

the Host Computer.

Disconnecting a Drive

Warning! If you remove the drive before you receive the notication that it’s safe to

do so, you could experience lost or corrupted data.

If the Host Computer’s OS is Windows, complete the following steps:

1. On the Notication tray, click the Safely Remove Hardware and Eject Media icon.

2. Click the storage device that you want to remove.

3. When the message appears indicating that it’s safe to remove the device,

disconnect the drive.

If the Host Computer’s OS is macOS, complete the following steps:

1. Close any windows that list the contents of the drive.

2. On your desktop, click and drag the USB Storage icon onto the Trash Can icon on

your desktop.

3. Wait 5 seconds, then disconnect the drive.

10. Use the Torx Screwdriver to tighten the Drive-Tray Screws.

11. Remove the backing from the Adhesive Strips and position them overtop of

the Drive-Cover Screws (two secrews per Adhesive Strip) on the bottom of the

Enclosure, sealing the Drive-Cover Screws.

Installing a 42 mm or 60 mm Drive

1. Using the Torx Screwdriver (included), remove the Drive-Cover Screws (x 4) from

the bottom of the Enclosure and remove the Cover Plate.

2. Place the Drive next to the Drive Tray and align the screw groove on the Drive with

the Adjustable Drive Length Holes on the Drive Tray.

3. Insert the Stando into the correct Adjustable Drive Length Hole (60 or 42)

according to the length of the Drive.

4. Gently slide the connector on the Drive (on a 30-degree angle) into the Drive

Connector on the Enclosure.

Note: The connector on your drive is keyed so that it only ts one way.

5. Lightly push the Drive down into position on the circuit board.

6. Insert the Drive-Mount Screw through the screw groove on the Drive and into the

Stando.

7. Place the Cover Plate back onto the bottom on the Enclosure. Make sure that the

Cover Plate is properly aligned with the top of the Enculosure creating a tight seal

and that nothing is obstructing the Cover Plate, in order to provide a water and dust

resistance seal.

8. Insert the Drive-Cover Screws back into the four corner on the bottom of the

Enclosure.

Produkt Specifikationer

Mærke:	StarTech.com
Kategori:	Ekstern harddisk
Model:	M2E1BRU31C

Har du brug for hjælp?

Hvis du har brug for hjælp til StarTech.com M2E1BRU31C stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ekstern harddisk StarTech.com Manualer

StarTech.com S251BMU313 Manual

2 September 2024

StarTech.com M2E1BRU31C Manual

2 September 2024

StarTech.com S352BU313R Manual

30 August 2024

StarTech.com SM22BU31C3R Manual

30 August 2024

StarTech.com S251BRU33 Manual

30 August 2024

StarTech.com S2510BPU337 Manual

30 August 2024

StarTech.com S251BU31315 Manual

30 August 2024

StarTech.com SMS2BU31C3R Manual

30 August 2024

StarTech.com IDE2SAT2 Manual

21 August 2024

StarTech.com BRACKET25X2 Manual

20 August 2024

Ekstern harddisk Manualer

Nyeste Ekstern harddisk Manualer

Elecom ELP-CED005UBK Manual

17 September 2025

InLine 00031M Manual

16 September 2025

GRAUGEAR G-2502-C-10G Manual

16 September 2025

SecureData SecureDrive BT Manual

10 September 2025

OWC ThunderBay Flex 8 Manual

4 September 2025

G-Technology G-RAID with Thunderbolt Manual

1 September 2025

G-Technology G-SPEED SHUTTLE XL with Thunderbolt 3 Manual

1 September 2025

G-Technology G-RAID with Thunderbolt 3 Manual

1 September 2025

G-Technology G-SPEED Shuttle with Thunderbolt 3 Manual

1 September 2025

G-Technology G-Drive Mobile USB Manual

1 September 2025