StarTech.com PEX1S953LP Manual

StarTech.com Ikke kategoriseret PEX1S953LP

Læs gratis den danske manual til StarTech.com PEX1S953LP (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om StarTech.com PEX1S953LP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: February 7, 2019 10:23 AM

Product Diagram (PEX1S953LP)

Port Function

1Serial Port • Used to connect a Serial Device

2Screws • Used to attach the Serial Port to the Bracket

• Used to secure a Serial Cable to the Serial Port

3Bracket • Used to attach the Card to your Computer

4PCI Express Bus

Connector

• Used to connect the PCI Express Serial Card to

your Computer’s Motherboard

5Jumper • Used to congure Serial Port power settings

6Printed Circuit Board • Components such as Jumpers are located on

this Board

7LP4 Power Connector • Used to connect a Power Source

1-Port PCI Express Serial Card with 16950 UART - Low-Prole

Requirements

• PCIe Slot

• Needle-Nose Pliers

For the latest requirements and full manual, please visit

www.startech.com/PEX1S953LP.

Installation

WARNING!

PCI Express Serial Cards can be severely damaged by static electricity. Make sure

that you are properly grounded before you open your or touch the Computer Case

PCI Express Serial Card Anti-Static Strap. You should wear an when you install any

computer component. If an isn’t available, discharge any built-up Anti-Static Strap

static electricity by touching a large for several seconds. Only Grounded Metal Surface

handle the by its edges and don’t touch the gold connectors.PCI Express Serial Card

Jumper Conguration

Note: Jumper Serial Devices conguration is a requirement when connecting that

require power through a . Serial Port

This can be moved into one of three dierent positions in order to set the Jumper

power output voltage for the . The default setting for the is , Serial Port Jumpers RI

which is the setting for no power. The can be moved to one of the other two Jumper

settings for or of power. To congure the , complete the following:5V 12V Jumper

1. Determine the power setting that is required for the .Serial Port

2. Locate the . The is labeled as on the .Jumper Jumper J1 Printed Circuit Board

3. Carefully remove the . Lift the straight up and o of the Jumper Jumper PCI Express

Serial Card.

Note: Always hold the by the edges.Card

4. Position the over the set of that correspond with the desired Jumper Pins Serial

Port Power Setting Jumper. See to determine where the Figure 1 should be

positioned.

5. Push the straight down and into place.Jumper

Note: Push the all the way into position for proper contact. Jumper

Produkt Specifikationer

Mærke:	StarTech.com
Kategori:	Ikke kategoriseret
Model:	PEX1S953LP
Bredde:	67 mm
Dybde:	98 mm
Højde:	150 mm
Vægt:	44 g
Brugervejledning:	Ja
Produktfarve:	Grøn
Pakkevægt:	112 g
Pakkedybde:	170 mm
Pakkebredde:	142 mm
Pakkehøjde:	30 mm
Opbevaringstemperatur (T-T):	-20 - 80 °C
Relativ luftfugtighed ved drift (H-H):	20 - 80 %
Driftstemperatur (T-T):	0 - 70 °C
Antal:	1
Harmoniseret systemkode (HS):	84733020
Bæredygtighedscertifikater:	CE, RoHS
Understøttede Linux-operativsystemer:	Ja
Hovedkassen højde (udvendigt):	315 mm
Hovedkassens længde (udvendigt):	685 mm
Hovedkassens bredde (udvendigt):	360 mm
Værtsgrænseflade:	PCIe
Intern:	Ja
Produkter pr. hovedkasse (udvendigt):	75 stk
Overholdelse af bæredygtighed:	Ja
Gennemsnitstid mellem fejl (MTBF):	277385 t
Understøttede operativsystemer til servere:	Windows Server 2003, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Monteringsbeslag inkluderet:	Ja
Flowkontrol support:	Ja
Seriel grænsefladetype:	RS-232
Antal serielle porte:	1
Baud hastighed:	921.4 Kbit/s
Data-bits:	5, 6,7, 8,9
Stop bits:	1, 1.5, 2
Perifere (Molex) strømstik (4-pin):	1
Output-grænseflade:	Seriel
Udvidelseskort standard:	PCIe 1.1
Chipsæt:	Asix AX99100
FIFO (først ind, først ud):	256 B
Flow Control type:	N, RTS/CTS, XON/XOFF
Paritetsbit:	Even, Mark, N,Odd, Space