StarTech.com PEX2S953 Manual

StarTech.com Ikke kategoriseret PEX2S953

Læs gratis den danske manual til StarTech.com PEX2S953 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om StarTech.com PEX2S953, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: November 27, 2019 1:15 PM

Product Diagram (PEX2S953)

Port Function

1Serial Ports • Connect up to two Serial Devices

2Stand-os • Attach the to the Bracket PCI Express Serial Card

• Secure the to the Serial Cables Serial Ports

3Bracket • Attach the to the PCI Express Serial Card Computer

4PCI Express Bus

Connector

• Connect the to the PCI Express Serial Card

Computer Motherboard

5Jumper • Congure the individual power Serial Connector

settings

6LP4 Power Connector • Used to connect an LP4 Power Source

2-Port PCI Express Serial Card with 16950 UART

Requirements

For the latest requirements please visit

www.startech.com/PEX2S953.

• PCIe Slot

• Needle-Nose Pliers

• (Optional) LP4 Power Source

Installation

WARNING! PCI Express Serial Cards can be severely damaged by static

electricity. Make sure that you are properly grounded before you open the

Computer Case PCI Express Serial Card or touch the . You should wear an

Anti-Static Strap Anti-Static when you install any computer component. If an

Strap isn’t available, discharge any built-up static electricity by touching a large

Grounded Metal Surface PCI Express Serial for several seconds. Only handle the

Card by its edges and don’t touch the gold connectors.

Jumper Conguration

Note: This is specially designed to allow for power output PCI Express Serial Card

from the ninth pin of the for that support power Serial Connector(s) Serial Devices

over serial. conguration is a requirement when connecting Jumper Serial Devices

that require power through a .Serial Connector

The can be moved into one of three dierent positions in order to set the Jumper

power output voltage for the . The default setting for the Serial Connector Jumpers

is , no power. The must be connected after conguring theRI LP4 Power Connector

Jumper 5V 12V Jumper to or of power. To congure the , complete the following:

1. Ensure the isComputer’s Power O.

2. Determine the power setting that is required for .Port One

3. Locate the for and carefully lift the straight up and o of Jumper Port One Jumper

the .PCI Express Serial Card

Notes: The Jumper for Port 1 is labeled as J1 on the Printed Circuit Board.

Always hold the Card by the edges.

4. Position the over the set of that correspond with the desired Jumper Pins Serial

Connector Power Setting Jumper. See to determine where the Figure 1 should be

positioned.

5. Push the straight down and into place.Jumper

Note: Push the all the way into position for proper contact. Jumper

2 2

Produkt Specifikationer

Mærke:	StarTech.com
Kategori:	Ikke kategoriseret
Model:	PEX2S953
Bredde:	63 mm
Dybde:	75 mm
Højde:	15 mm
Vægt:	56 g
Produktfarve:	Grøn
Pakkevægt:	136 g
Pakkedybde:	142 mm
Pakkebredde:	170 mm
Pakkehøjde:	30 mm
Opbevaringstemperatur (T-T):	-20 - 100 °C
Relativ luftfugtighed ved drift (H-H):	5 - 85 %
Driftstemperatur (T-T):	-10 - 80 °C
Antal:	1
Hurtig installationsvejledning:	Ja
Harmoniseret systemkode (HS):	84733020
Bæredygtighedscertifikater:	CE, RoHS
Understøttede Linux-operativsystemer:	Ja
Hovedkassen højde (udvendigt):	306 mm
Hovedkassens længde (udvendigt):	345 mm
Hovedkassens bredde (udvendigt):	685 mm
Værtsgrænseflade:	PCIe
Intern:	Ja
Produkter pr. hovedkasse (udvendigt):	75 stk
Overholdelse af bæredygtighed:	Ja
Gennemsnitstid mellem fejl (MTBF):	222366 t
Understøttede operativsystemer til servere:	Windows Server 2003, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Seriel grænsefladetype:	RS-232
Antal serielle porte:	2
Baud hastighed:	921.6 Kbit/s
Data-bits:	5, 6,7, 8,9
Stop bits:	1, 1.5, 2
Output-grænseflade:	Seriel
Udvidelseskort standard:	PCIe 1.1
Chipsæt:	Asix AX99100
FIFO (først ind, først ud):	256 B
Flow Control type:	N, RTS/CTS, XON/XOFF
Paritetsbit:	Even, Mark, N,Odd, Space