StarTech.com PEX4S953 Manual

StarTech.com Ikke kategoriseret PEX4S953

Læs gratis den danske manual til StarTech.com PEX4S953 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om StarTech.com PEX4S953, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: October 31, 2019

Product Diagram (PEX4S953 and PEX4S953LP)

Port Function

1Break-out Cable Port

• Connect the to connect 4-Port DB9 Break-out Cable

up to 4 Serial Devices

2Stand-os

• Attach the to the Bracket PCI Express Serial Card

• Secure the to the 4-Port DB9 Break-out Cable

Break-out Cable Port

3Bracket • Attach the to the PCI Express Serial Card Computer

PCI Express Bus

Connector

• Connect the to the PCI Express Serial Card

Computer Motherboard

5Jumpers

• Congure the individual power Serial Connector

settings

6LP4 Power Connector • Used to connect an LP4 Power Source

4-Port PCI Express RS232 Serial Card - 16950 UART

Requirements

For the latest requirements please visit:

www.startech.com/PEX4S953 www.startech.com/PEX4S953LP. - or -

• PCIe Slot

• Needle-Nose Pliers

• (Optional) LP4 Power Source

Installation

WARNING!

PCI Express Serial Cards can be severely damaged by static electricity. Make sure

that you are properly grounded before you open the or touch the Computer Case

PCI Express Serial Card Anti-Static Strap . You should wear an when you install

any computer component. If an isn’t available, discharge any Anti-Static Strap

built-up static electricity by touching a large for several Grounded Metal Surface

seconds. Only handle the by its edges and don’t touch PCI Express Serial Card

the gold connectors.

Jumper Conguration

Note: This is specially designed to allow for power output PCI Express Serial Card

from the ninth pin of the for that support power Serial Connector(s) Serial Devices

over serial. conguration is a requirement when connecting Jumper Serial Devices

that require power through a .Serial Connector

The can be moved into one of three dierent positions in order to set the Jumper

power output voltage for the . The default setting for the Serial Connector Jumpers

is , no power. The must be connected after conguring theRI LP4 Power Connector

Jumper 5V 12V Jumper to or of power. To congure the , complete the following:

1. Ensure the isComputer Power O.

2. Locate the for and carefully remove the . Lift the Jumper Port One Jumper Jumper

straight up and o of the .PCI Express Serial Card

Notes: The is located on the right hand side, labeled as on the Jumper Port 1

. Printed Circuit Board

Always hold the by the edges.Card

3. Determine the power setting that is required for .Port One

4. Position the over the set of that correspond with the desired Jumper Pins Serial

Connector Power Setting Jumper. See to determine where the Figure 1 should be

positioned.

Produkt Specifikationer

Mærke:	StarTech.com
Kategori:	Ikke kategoriseret
Model:	PEX4S953
Bredde:	63 mm
Dybde:	75 mm
Højde:	15 mm
Vægt:	50 g
Produktfarve:	Grøn
Pakkevægt:	371 g
Pakkedybde:	210 mm
Pakkebredde:	150 mm
Pakkehøjde:	50 mm
Opbevaringstemperatur (T-T):	-20 - 100 °C
Relativ luftfugtighed ved drift (H-H):	5 - 85 %
Driftstemperatur (T-T):	-10 - 80 °C
Antal:	1
Hurtig installationsvejledning:	Ja
Kabler inkluderet:	Seriel
Certificering:	CE, FCC, Microsoft WHQL
Harmoniseret systemkode (HS):	84733020
Bæredygtighedscertifikater:	RoHS
Understøttede Linux-operativsystemer:	Ja
Hovedkassen højde (udvendigt):	240 mm
Hovedkassens længde (udvendigt):	480 mm
Hovedkassens bredde (udvendigt):	340 mm
Værtsgrænseflade:	PCIe
Intern:	Ja
Produkter pr. hovedkasse (udvendigt):	16 stk
Gennemsnitstid mellem fejl (MTBF):	214358 t
Understøttede operativsystemer til servere:	Windows Server 2003, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Monteringsbeslag inkluderet:	Ja
Seriel grænsefladetype:	RS-232
Antal serielle porte:	4
Baud hastighed:	921.6 Kbit/s
Data-bits:	5, 6,7, 8,9
Stop bits:	1, 1.5, 2
Output-grænseflade:	Seriel
Udvidelseskort formfaktor:	Fuld højde/ lav profil
Chipsæt:	Asix AX99100
FIFO (først ind, først ud):	256 B
Flow Control type:	N, RTS/CTS, XON/XOFF
Paritetsbit:	Even, Mark, N,Odd, Space