StarTech.com PEX8S1050LP Manual

StarTech.com Ikke kategoriseret PEX8S1050LP

Læs gratis den danske manual til StarTech.com PEX8S1050LP (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 9 anmeldelser. Har du et spørgsmål om StarTech.com PEX8S1050LP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: December 17, 2019 12:04 PM

Product Diagram (PEX8S1050LP)

Component Function

S5 - S8: DB44 Pin

Connector to 4-Port

Breakout Cable

• Used to connect the DB44 to 4-Port DB9

Breakout Cable.

JP 5 - Power Over

Serial Connector

• Used to set pin 9 on the DB9 connector (S1 -

S4) to RI (no power) or to DC power. The JP2

Aux Power Source Selector determines the

voltage 12 or 5.

• Default position is RI.

S1 - S4: DB44 Pin

Connector to 4-Port

Breakout Cable

• Used to connect the DB44 to 4-Port DB9

Breakout Cable.

4PCI Express Connector

• Used to connect the to PCI Express Card

the PCI Express expansion slot on the Host

Computer.

8-Port PCI Express Low Prole RS232 Serial Card | 16C1050 UART

5JP1: PME

• Used to enable or disable the wake from sleep

setting.

• Default position is disable.

6JP4: Mode

• Used for factory testing.

• For normal use the jumper must be set to CEN.

JP6: S5 - S8

Power Over Serial

Connectors

• Used to enable or disable power over serial for

S5 - S8 connectors.

JP2: AUX Power

Source Selector

• Used to select the DC power source for Pin 9 on

the DB9 connector.

• Power supplied by Internal 12V:

motherboard’s PCI Express Slot.

• Power supplied by J3 Power External 12V:

Connector.

• Power supplied by J3 Power External 5V:

Connector.

J3 Aux. Power

Connector

• Used to connect an external power source to

the .Serial Card

Requirements

For the latest requirements, please visit www.startech.com/PEX8S1050LP

Installation

WARNING! PCI Express cards can be severely damaged by static electricity. Be sure

that you are properly grounded before touching the .Serial Card

1. Turn O the Host Computer.

2. Remove the chassis cover from the .Host Computer

3. Locate a , using a (sold separately) remove the PCI Express Slot Screwdriver Screw

used to secure the and set the aside. PCI Express Slot Cover Screw

4. Align the on the with a . While PCI Express Connector Serial Card PCI Express Slot

applying pressure evenly across the top edge of the , insert the Serial Card Serial

Card PCI Express Slot Serial Cardinto the , ensuring that the is properly aligned

with the rear panel slot.

5. Using a and the removed in step 3, secure the to Screwdriver Screw Serial Card

the motherboard and rear chassis. Secure the additional serial port provided by the

daughter board (smaller circuit board) to an adjacent rear bracket.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a lifetime warranty.

For further information on product warranty terms and conditions, please refer to .www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT: startech.com/it

JP: startech.com/jp

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

DB44 Pin Assignment

Port 1 Port 2 Port 3 Port 4

42 DCD1 39 DCD2 35 DCD3 31 DCD4

14 RXD1 10 RXD2 6 RXD3 2 RXD4

13 TXD1 9 TXD2 5 TXD3 1 TXD4

29 DTR1 25 DTR2 21 DTR3 17 DTR4

44 GND 41 GND 37 GND 33 GND

30 DSR1 26 DSR2 22 DSR3 18 DSR4

15 RTS1 11 RTS2 7 RTS3 3 RTS4

28 CTS1 24 CTS2 20 CTS3 16 CTS4

43 RI 1 40 RI 2 36 RI 3 32 RI 4

6. Place the chassis cover back on the .Host Computer

7. Connect the to the on the 4-Port Breakout Cables DB44 Pin Connectors Serial

Card.

8. Power on the . When the has been rebooted, the Host Computer Host Computer

operating system will detect that the has been installed.Serial Card

Installing the Drivers

1. Using a web browser, navigate to .www.startech.com/PEX8S1050LP

2. On the Product page, click the tab located in the middle of the screen.Support

3. In the section, click on the driver link that corresponds with Drivers and Downloads

the operating system running on the host laptop.

Note: if there is only one driver listed click the driver and select the operating system

once the le is downloaded.

4. Click the driver folder will open listing the compatible operting systems.Open,

5. Click the folder for the version of operating system that you are running.

6. Click the (windows) or (macOS) le.Setup.exe Install.pkg

7. Follow the on-screen prompts to complete the installation.

Produkt Specifikationer

Mærke:	StarTech.com
Kategori:	Ikke kategoriseret
Model:	PEX8S1050LP
Bredde:	22 mm
Dybde:	145 mm
Højde:	60 mm
Vægt:	116 g
Brugervejledning:	Ja
Produktfarve:	Gul
Pakkevægt:	750 g
Pakkedybde:	290 mm
Pakkebredde:	190 mm
Pakkehøjde:	70 mm
Opbevaringstemperatur (T-T):	-20 - 85 °C
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Driftstemperatur (T-T):	0 - 55 °C
Antal:	1
Kabler inkluderet:	Seriel
Certificering:	CE, FCC, TAA
Harmoniseret systemkode (HS):	84733020
Bæredygtighedscertifikater:	RoHS
Understøttede Linux-operativsystemer:	Ja
Hovedkassen højde (udvendigt):	315 mm
Hovedkassens længde (udvendigt):	510 mm
Hovedkassens bredde (udvendigt):	400 mm
Værtsgrænseflade:	PCIe
Intern:	Ja
Produkter pr. hovedkasse (udvendigt):	14 stk
Understøttede operativsystemer til servere:	Windows Server 2003, Windows Server 2008 R2, Windows Server 2012, Windows Server 2016, Windows Server 2019
Monteringsbeslag inkluderet:	Ja
Flowkontrol support:	Ja
Seriel grænsefladetype:	RS-232
Antal serielle porte:	8
Baud hastighed:	926.1 Kbit/s
Data-bits:	5, 6,7, 8
Stop bits:	1, 1.5, 2
Output-grænseflade:	Seriel
Udvidelseskort formfaktor:	Fuld højde/ lav profil
Chipsæt:	ASMEDIA - ASM1083, SYSTEMBASE - SB16C1058PCI
FIFO (først ind, først ud):	256 B
Flow Control type:	RTS/CTS, XON/XOFF
Paritetsbit:	Even, N,Odd