StarTech.com USB31CSAT3CB Manual

StarTech.com Ikke kategoriseret USB31CSAT3CB

Læs gratis den danske manual til StarTech.com USB31CSAT3CB (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om StarTech.com USB31CSAT3CB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Instruction manual

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

Manual Revision: 08/12/2015

For the latest information, technical specications, and support for

this product, please visit www.startech.com/USB31CSAT3CB.

Packaging contents

• 1 x USB 3.1 to SATA 2.5 in. HDD adapter cable with USB-C™ port

• 1 x instruction manual

System requirements

• USB-enabled computer system with an available USB Type-C™ port

• 2.5 in. SATA drive

Note: To obtain the maximum USB throughout, you must use a

computer with a USB 3.1 Gen 2 port.

System requirements are subject to change. For the latest

requirements, please visit www.startech.com/USB31CSAT3CB.

USB31CSAT3CB

USB 3.1 Gen 2 (10 Gbps) Adapter Cable for SATA Drives - with USB-C

*actual product may vary from photos

Product overview

USB-C connector

SATA connector for

2.5 in. HDD or SSD

Connect the adapter

Warning! Hard drives and storage enclosures should be handled

carefully, especially when they’re transported. If you’re not careful

with your drives, you may lose data as a result. Always handle

storage devices with caution. Make sure that you’re properly

grounded by wearing an anti-static strap when you install any

computer component. If an anti-static strap isn’t available, touch a

large grounded metal surface for several seconds to discharge any

built-up static electricity.

Note: The USB31CSAT3CB adapter cable only works with 2.5 in.

HDD (hard drives) and SSD (solid state drives), because 3.5 in. HDDs

and optical drives require 12V of power and the adapter cable only

provides 5V of power.

1. Connect the SATA connector on the adapter cable to the SATA

receptacle on your 2.5 in. HDD or SDD.

2. Connect the USB-C connector on the adapter cable to a USB port

on the host computer system.

After the adapter is connected to a computer, the necessary software

automatically installs and the drive is accessible as though it were

installed internally in the system.

Before you use the drive, you must format it according to your

operating system requirements. To format your newly attached drive

or to create partitions, consult the documentation that came with

your operating system at the time of purchase.

About powering the drive

The drive adapter doesn’t require an external power supply, as it

receives enough power from the USB bus that it’s connected to.

Initialize the drive

If your computer doesn’t automatically recognize the drive, you need

to initialize and format it to the operating system.

If you use a computer that’s running Windows® 2000, Windows® XP,

Windows Vista®, or Windows® 7, do the following:

1. Depending on the version of the OS that you’re running, do one

of the following:

• On your desktop, right-click .My Computer

• On your desktop, right-click .Computer

2. Click .Manage

3. On the Computer Management Disk Management screen, click .

4. A dialog window appears and asks you to initialize the hard drive.

Depending on the version of Windows that you’re running, you

have the option to create either an or a disk.MBR GPT

Note: GPT (GUID partition) is required for hard drives that are larger

than 2 TB, but GPT isn’t compatible with some earlier versions of

operating systems. Both earlier and later versions of operating

systems support MBR.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the

equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)

to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all

trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and

access our comprehensive selection of online tools, documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two-year warranty.

StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for

repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from

misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,

consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not

allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

5. Locate the disk that is labeled as . To conrm that the Unallocated

hard drive is the correct one, check the hard drive capacity.

6. Right-click the section of the window that says and Unallocated

click .New Partition

7. To initialize the drive in the format of your choice, complete the

on-screen instructions.

Disconnecting the drive

Disconnect the drive on a computer running a version

of Windows OS

1. In the task bar on your desktop, click the Safely remove Hardware

and Eject Media icon.

2. In the list that appears, click the device that you want to remove.