Steren MOC3011 Manual

Steren Ikke kategoriseret MOC3011

Læs gratis den danske manual til Steren MOC3011 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Steren MOC3011, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

(250 Volts Peak)

The MOC3010 Series consists of gallium arsenide infrared emitting diodes,

optically coupled to silicon bilateral switch and are designed for applications

requiring solate ria riggering ow–curren solate witching igh i d t c t , l t i d ac s , h

electrical isolation (to 7500 Vac peak), high detector standoff voltage, small

size, and low cost.

•

To order devices that are tested and marked per VDE 0884 requirements, the

sux ”V” must be included at end of part number. VDE 0884 is a test option.

Recommended for 115 Vac(rms) Applications:

•Solenoid/Valve Controls

•Lamp Ballasts

•Interfacing Microprocessors to 115 Vac Peripherals

•Motor Controls

•Static ac Power Switch

•Solid State Relays

•Incandescent Lamp Dimmers

MAXIMUM RATINGS (TA = 25 C unless otherwise noted)°

Rating Symbol Value Unit

INFRARED EMITTING DIODE

Reverse Voltage VR3 Volts

Forward Current — Continuous IF60 mA

Total Power Dissipation @ T

A = 25 C°

Negligible Power in Transistor

Derate above 25°C

PD100

1.33

mW/ C°

OUTPUT DRIVER

O–State Output Terminal Voltage VDRM 250 Volts

Peak Repetitive Surge Current

(PW = 1 ms, 120 pps)

ITSM 1 A

Total Power Dissipation @ T

A = 25 C°

Derate above 25°C

PD300

mW/ C°

TOTAL DEVICE

Isolation Surge Voltage(1)

(Peak ac Voltage, 60 Hz, 1 Second Duration)

VISO 7500 Vac(pk)

Total Power Dissipation @ T

A = 25 C°

Derate above 25°C

PD330

4.4

mW/ C°

Junction Temperature Range T

J– 40 to +100 C°

Ambient Operating Temperature Range(2) TA– 40 to +85 C°

Storage Temperature Range

(2) T

stg – 40 to +150 C°

Soldering Temperature (10 s) T

L260 C°

1. Isolation surge voltage, VISO, is an internal device dielectric breakdown rating.

1. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common.

2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions.

Preferred devices are Motorola recommended choices for future use and best overall value.

GlobalOptoisolator is a trademark of Motorola, Inc.

Order this document

by MOC3010/D

SEMICONDUCTOR TECHNICAL DATA

GlobalOptoisolator฀

฀ Motorola, Inc. 1995

*Motorola Preferred Device

COUPLER SCHEMATIC

[IFT = 15 mA Max]

STANDARD THRU HOLE

CASE 730A–04

[IFT = 10 mA Max]

[IFT = 5 mA Max]

1. ANODE

2. CATHODE

3. NC

4. MAIN TERMINAL

5. SUBSTRATE

DO NOT CONNECT

6. MAIN TERMINAL

STYLE 6 PLASTIC

(Replaces MOC3009/D)

2 Motorola Optoelectronics Device Data

ELECTRICAL CHARACTERISTICS (TA = 25 C unless otherwise noted)°

Characteristic Symbol Min Typ Max Unit

INPUT LED

Reverse Leakage Current

(VR = 3 V)

IR— 0.05 100 Aµ

Forward Voltage

(IF = 10 mA)

VF— 1.15 1.5 Volts

OUTPUT DETECTOR (I

F = 0 unless otherwise noted)

Peak Blocking Current, Either Direction

(Rated VDRM(1))

IDRM — 10 100 nA

Peak On–State Voltage, Either Direction

(ITM = 100 mA Peak)

TM — 1.8 3 Volts

Critical Rate of Rise of Off–State Voltage (Figure 7, Note 2) dv/dt — 10 — V/ sµ

COUPLED

LED Trigger Current, Current Required to Latch Output

(Main Terminal Voltage = 3 V

(3)) MOC3010

MOC3011

MOC3012

—

Holding Current, Either Direction IH— 100 — Aµ

1. Test voltage must be applied within dv/dt rating.

2. This is static dv/dt. See Figure 7 for test circuit. Commutating dv/dt is a function of the load–driving thyristor(s) only.

3. All devices are guaranteed to trigger at an I

F value less than or equal to max I

FT. Therefore, recommended operating I

F lies between max

3. IFT (15 mA for MOC3010, 10 mA for MOC3011, 5 mA for MOC3012) and absolute max I

F (60 mA).

–800

TYPICAL ELECTRICAL CHARACTERISTICS

TA = 25 C°

Figure 1. LED Forward Voltage versus Forward Current

1.8

1.6

1.4

1.2

1 10 100 1000

IF, LED FORWARD CURRENT (mA)

VF, FORWARD VOLTAGE (VOLTS)

PULSE ONLY

PULSE OR DC

Figure 2. On–State Characteristics

–3

VTM, ON–STATE VOLTAGE (VOLTS)

–400

+400

+800

–2 –1 0 1 2 3

TM, ON-STATE CURRENT (mA)

TA = –40

Produkt Specifikationer

Mærke:	Steren
Kategori:	Ikke kategoriseret
Model:	MOC3011

Har du brug for hjælp?

Hvis du har brug for hjælp til Steren MOC3011 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Steren Manualer

Steren BOS-408 Manual

6 Juni 2024

Steren USB-MIDI Manual

6 Juni 2024

Steren 252-921 Manual

6 Juni 2024

Steren 500-900 Manual

6 Juni 2024

Steren USB-455 Manual

6 Juni 2024

Steren 200-385 Manual

6 Juni 2024

Steren STV-021 Manual

6 Juni 2024

Steren ANT-UHF 20 Manual

6 Juni 2024

Steren CDA-1P Manual

6 Juni 2024

Steren PIC-605 Manual

6 Juni 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Dormakaba Crane S1 Manual

19 Oktober 2025

Shape BP8000 Manual

19 Oktober 2025

Shape ALPKIT Manual

19 Oktober 2025

Shape COMPOFIC Manual

19 Oktober 2025

ResMed AirFit F10 Manual

18 Oktober 2025

Dormakaba Auditcon T52 Manual

18 Oktober 2025

Shape BP0008EVF Manual

18 Oktober 2025

ResMed Mirage Micro Manual

18 Oktober 2025

AstralPool Swimspa Compact Manual

18 Oktober 2025

ResMed Chin Restraint Manual

18 Oktober 2025